Toshiba MMD-AP0186BHP-E — установка внутреннего блока: пошаговое руководство и советы [8/28]
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Toshiba MMD-AP0186BHP-E — установка внутреннего блока: пошаговое руководство и советы [8/28]

Toshiba MMD-AP0186BHP-E [8/28] Installation of indoor unit
–7–
Installation of hanging bolt
• Consider the piping / wiring after the unit is hung to
determine the location of the indoor unit installation
and orientation.
• After the location of the indoor unit installation has
been determined, install hanging bolts.
• For the dimensions of the hanging bolt pitches, refer
to the external view.
• When a ceiling already exists, lay the drain pipe,
refrigerant pipe, control wires, and remote controller
wires to their connection locations before hanging
the indoor unit.
Procure hanging bolts washer and nuts for installing
the indoor unit (these are not supplied).
Installation of hanging bolt
Use M10 hanging bolts (4 pcs, locally procured).
Matching to the existing structure, set pitch according
to size in the unit external view as shown below.
Installation of indoor unit
Treatment of ceiling
The ceiling differs according to structure of building.
For details, consult your constructor or interior finish
contractor.
In the process after the ceiling board has been
removed, it is important to reinforce ceiling foundation
(frame) and to keep horizontal level of installed ceiling
correctly in order to prevent vibration of ceiling board.
• Attach the nuts and the M10 flat washers to the
hanging bolt.
• Put washers at up and down of the hanging bracket
of the indoor unit to hang down the indoor unit.
• Check that four sides are horizontal with a level
gauge. (Horizontal degree: Within 5 mm)
REQUIREMENT
• Hang the unit in a horizontal position.
When unit is hanged to slant, it may cause overflow of
drainage.
• Install the unit within the dimension according to the
figure below.
• Use level gauge to confirm whether the unit is hang
horizontally.
Hanging bolt M10 or W3/8 4 pieces
Nut M10 or W3/8 12 pieces
Washer M10 8 pieces
New concrete slab
Install the bolts with insert brackets or anchor bolts.
Steel flame structure
Use existing angles or install new support angles.
Existing concrete slab
Use a hole-in anchors, hole-in plugs, or a hole-in bolts.
Rubber
Anchor bolt
(Blade type
bracket)
(Slide type
bracket)
(Pipe hanging
anchor bolt)
Hanging bolt
Hanging bolt
Support angle
Nut
(W3/8 or M10)
M10 flat washer
M10 flat washer
Hanging bolt
(W3/8 or M10)
Nut
(W3/8 or M10)
0 to 5 mm
±5 mm
Set the air intake and air
discharge sides are within 5 mm
with each other.
Set the drain pipe connecting
port side within 5 mm lower
than opposite side.
Front view
Side view
Mounting filter rails and filters
1 Mount the filter rail so that the hooks fit into the corresponding holes.
(Note that the upper and lower filter rails are not identical.)
Changing from back air intake to under air intake
1 Remove the filters on back of unit.
2 Remove the suction board cover attached to the bottom, and screw it to the back of unit.
3 Mount the supplied rail to the bottom, then set the filter.
* The sizes of the left and right covers of SM80 class unit are not identical. As shown in the figure, re-mount the
covers left-right reversed by facing the hook part upwards.
2 Mount the filter stopper.
CAUTION
When mounting the rails, push them until the 3
latches click.
3 Slide and push the filters until it stop.
* Insert the filters into the direction which the
arrows, carved on the filters, show. (2 filters
are identical)
Filter stopper (accessory)
Lower filter rail
Square hole
Fit this hook into
the square hole.
Upper filter rail
13-EN 14-EN

Содержание

Похожие устройства

Узнайте, как правильно установить внутренний блок кондиционера. Пошаговые инструкции по монтажу, выбору крепежа и проверке уровня для надежной работы.

Скачать