Rovus ULTRA SMART CORDLESS IRON Инструкция по эксплуатации онлайн [5/80] 282967

Rovus ULTRA SMART CORDLESS IRON Инструкция по эксплуатации онлайн [5/80] 282967
5
TEMPERATURE CONTROL SETTING
•
This is an original and innovative steam iron. The soleplate is always in a state of constant temperature, therefore there is no need classifying the clothing. Suitable for all the fabrics such as silk,
synthetic ber, wool, cotton and linen.
SETTING THE TEMPERATURE
•
Insert the plug in the wall socket and position the iron upright.
•
The desired temperature has been reached when the indicator light has turned o. The indicator light (13) will turn on and o from time to time, indicating that the selected temperature is
being maintained.
SPRAYING
This function can be used any time and it does not aect the ironing temperature.
•
Fill water into the iron as described above
•
Aim the nozzle towards the garment.
•
Press the spray button (12).
STEAM IRONING
The pilot light is on once the iron is plugged into the socket. After indicator light is o, rstly make sure there is water in the water tank and then press the steam button (5). When the steam comes
out of the soleplate, the steam ironing function is realized.
Notice: Do not press the steam button as soon as lling the tank with water. Please wait for heating until the indicator light (13) is o and then press steam button (5) – steam will penetrate through
soleplate.
NOTE: If this procedure is not fully followed water might start dripping from the bottom. If this happens, release the button immediately and heat until indicator light (13) turns o. If the soleplate is
dry enough, the iron can be normally used again. The concrete procedures are as follows:
•
Fill water into the iron as described.
•
Position the iron upright.
•
Connect the iron to a suitable power supply outlet.
•
After indicator light (13) turns o, the iron is ready for use.
•
Hold the steam button (5), and the steam comes out from the soleplate.
Notice: With conventional steam ironing, water may leak from the soleplate if too low temperature has been selected. Once it happens, release the button immediately and heat until indicator light
turns o. If the soleplate is dry enough, the iron can be normally used again. The steam (when used cordless) lasts for 25 to 40 seconds.
BURST OF STEAM
The iron has the powerful burst of steam function. This function provides an extra amount of steam to remove stubborn wrinkles, suitable for fabrics like cotton, linen and jeans. Press burst of steam
button to iron in either horizontal or vertical orientation.
•
Fill the iron with water as described above.
•
Turn on the iron and heat for two minutes.
•
The indicator light turns o when temperature is reached.
•
The iron is ready for use.
•
Press the burst button (5) once.
•
Steam will penetrate into the garment removing the wrinkles.
•
Wait three seconds before pressing the burst button again when there are stubborn wrinkles.
DRY IRONING
•
Connect the iron to a suitable power supply.
•
Make sure not to press the steam button (12).
•
After indicator light (13) turns o, the iron is ready for use.
•
Dry ironing should allow 4 minutes to 6 minutes of use.
ANTI-SCALE SYSTEM
Your iron contains an anti-scale cartridge to reduce scale deposits.
This considerably prolongs the operational life of your iron.
The anti-scale cartridge is an integral part of the water tank and doesn’t need replacement.
SELF-CLEAN FUNCTION
1. The iron has the self-clean function in order to remove impurities and scale deposits.
2. Make sure not to press steam button.
3. Add water up to the MAX” level.
4. Connect the iron into the power supply.
5. Pull out of the plug when the indicator light (13) turns o. Lift the self-cleaning switch by pulling the button backwards - large amounts of steam and water will be discharged from the soleplate,
along with impurities and scale deposits.
6. Push back down the self-cleaning button as soon as all water in the tank has run out.
7. You can repeat the same procedure if needed.
HOW TO OPERATE
Device needs approximately 50-70 seconds for the initial heating up (indicator light will turn o). Following re-heating needs 25-35 seconds.
There are two options of using the iron:
•
Wireless – the locking switch (1) should be positioned in the position.
•
With wire – the locking switch (1) should be positioned in the position.
NOTE: Always pour out any remaining water from the iron after usage.
CARE AND CLEANING
1. Disconnect the iron from power supply and let the iron completely cool down.
2. Deposits and other residues on the sole plate can be removed with a cloth soaked in a vinegar/water solution.
3. The casing may the wiped with a damp cloth and then polished with a dry one.
4. Never use any abrasives to clean the sole plate.
5. Keep the sole plate smooth; avoid contact with metal objects.
STORAGE
•
Disconnect the iron from the power supply.
•
Pour any remaining water out of the water tank.

Содержание

Похожие устройства