Timberk Cloud TAP FL150 SF (W) [5/24] Operation of the instrument
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Timberk Cloud TAP FL150 SF (W) [5/24] Operation of the instrument

Timberk Cloud TAP FL150 SF (W) [5/24] Operation of the instrument
www.timberk.com • electric air purifier
5
Power Control – To operate the TAP FL150 SF air purifier, press the ON/OFF
button to turn on the air purifier. Press the button again to turn the unit off.
Timer Control – The TAP FL150 SF air purifier can be programmed to turn off
after a preset amount of time. Press the «TIMER» button to program the timer.
Each press will add one hour up to a total of 24 hours. Keeping the button
pressed will automatically increase to 24 hours, 1 hour at a time, after that it
will turn back to off.
Fan Speed Control – The TAP FL150 SF has three different speeds of
cleaning, LOW, MED and HI. Press «SPEED» button to cycle the settings and
select the fan speed you desire. The speed state will be shown on the LED
display.
Clean Filter Indicator Light – The TAP FL150 SF Clean Filter Indicator Light
will turn on each time the filter needs to be cleaned. To reset the filter indicator,
press the TIMER and the ON/OFF buttons together for 3 seconds. The
CLEAN FILTER light will flash 3 times and then turn off completely, indicating
the unit has been reset.
Night Mode – If the UV light bar is too bright, press the «Night Mode» button
to turn off the UV light bar feature, and the lighted display. The ON/OFF
indicator, however, will remain lit. The night mode only turns off UV light bar not
the actual UV feature.
Reset Filter Control – Press down the «TIMER» and «ON/OFF» button for 3
seconds, the clean filter light will flash 3 times and then the clean filter light will
turn off, indicating the unit has been reset.
UV Control – Press the UV/VOC control button «UV/VOC» to turn on the UV
lamp to kill harmful airborne germs and reduce harmful VOC (volatile organic
compounds). Press it again to turn off the UV and VOC.
7. OPERATION OF THE INSTRUMENT
NOTE:
Always make sure the TAP FL150 SF is turned off and
unplugged before cleaning.
•Vacuuming will restore performance of the permanent
HEPA-type filter. However, the filter may appear stained.
This is normal and does not affect performance in any
way.
• Do not use water or any household cleaners or
detergents to clean the permanent HEPA-type filter.
• The inlet grill may be cleaned (after unit is turned off
and unplugged) with a vacuum or a slightly damp cloth.
1 2 3 4
Keep the TAP FL150 SF functioning properly by cleaning the permanent
HEPA-type filter every four weeks. More frequent cleaning will be necessary
if the unit is located in an area with a high level of airborne contaminants
(excessive amounts of smoke, pet dander, etc.).
8. CLEANING AND MAINTENANCE INSTRUMENT
Cleaning the permanent HEPA-type filter.
1. Release the inlet grill by pressing on the locking latch (see diagram of
Main Parts).
2. Remove the inlet grill from the unit as shown below.
3. Grasp the left and right frames of the permanent HEPA-type filter through
the indentations on the sides of the filter enclosure and remove the filter.
4. To clean the permanent HEPA-type filter, use the brush or crevice
attachment with a vacuum cleaner. Run the attachment along the inlet and
outlet side of the filter, cleaning between the crevices as much as possible.
Do not use water or any household cleaners or detergents to clean the
permanent HEPA-type filter.
5. Once the permanent HEPA-type filter has been cleaned and checked
for any possible damage, replace the filter back in the reverse direction
described here. Plug in the unit and hold down Timer + Power On button
for 3 seconds. The clean filter light will go off and your cleaning maintenance

Содержание

Похожие устройства

Скачать