Hitachi G12SR4-NS — essential Safety Warnings for Grinding and Cutting Operations [3/144]
![Hitachi G12SR4-NS [3/144] Safety warnings specific for grinding and abrasive cutting off operations](/views2/1366210/page3/bg3.png)
3
English
SAFETY WARNINGS COMMON FOR
GRINDING OR ABRASIVE CUTTING-
OFF OPERATIONS
a) This power tool is intended to function as a
grinder or cut-off tool. Read all safety warnings,
instructions, illustrations and specifi cations
provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
b) Operations such as sanding, wire brushing or
polishing are not recommended to be performed
with this power tool.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
c)
Do not use accessories which are not specifi cally
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
d)
The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can
break and fl y apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted
by fl anges, the arbour hole of accessory must fi t
the locating diameter of the fl ange.
Accessories that do not match the mounting hardware of
the power tool will run out of balance, vibrate excessively
and may cause loss of control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
h)
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping fl ying
debris generated by various operations. The dust mask
or respirator must be capable of fi ltrating particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a broken accessory may
fl y away and cause injury beyond immediate area of
operation.
j)
Hold the power tool by insulated gripping surfaces
only, when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and could
give the operator an electric shock.
k) Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning accessory.
l) Never lay the power tool down until the accessory
has come to a complete stop.
The spinning accessory may grab the surface and pull
the power tool out of your control.
m)
Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
o)
Do not operate the power tool near fl ammable materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED
WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the accessory’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing
the wheel to climb out or kick out. The wheel may either jump
toward or away from the operator, depending on direction of
the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a)
Maintain a fi rm grip on the power tool and position your
body and arm to allow you to resist kickback forces.
Always use auxiliary handle, if provided, for maximum
control over kickback or torque reaction during start-up.
The operator can control torque reactions or kickback
forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power
tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to the
wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback and loss of control.
SAFETY WARNINGS SPECIFIC FOR
GRINDING AND ABRASIVE CUTTING-
OFF OPERATIONS
a) Use only wheel types that are recommended for
your power tool and the specifi c guard designed
for the selected wheel.
Wheels for which the power tool was not designed
cannot be adequately guarded and are unsafe.
b) The grinding surface of centre depressed wheels
must be mounted below the plane of the guard lip.
An improperly mounted wheel that projects through the
plane of the guard lip cannot be adequately protected.
0000Book_G10SR4.indb 30000Book_G10SR4.indb 3 2016/01/29 19:00:042016/01/29 19:00:04
Содержание
- G 10sr p.1
- G 13sr4 p.1
- G 12sr p.1
- Kezelési utasítás návod k obsluze kullanım talimatları instrucţiuni de utilizare navodila za rokovanje pokyny na manipuláciu инструкция за експлоатация uputstvo za rukovanje upute za rukovanje iнструкції щодо поводження з пристроєм инструкция по эксплуатации p.1
- Handling instructions bedienungsanleitung mode d emploi istruzioni per l uso gebruiksaanwijzing instrucciones de manejo instruções de uso bruksanvisning brugsanvisning bruksanvisning käyttöohjeet οδηγίες χειρισμού instrukcja obsługi p.1
- General power tool safety warnings p.2
- English p.2
- Safety warnings specific for grinding and abrasive cutting off operations p.3
- Safety warnings common for grinding or abrasive cutting off operations p.3
- Kickback and related warnings p.3
- English p.3
- General safety instructions for grinders p.4
- English p.4
- Additional safety warnings specific for abrasive cutting off operations p.4
- Additional safety warnings p.4
- Standard accessories p.5
- Specifications p.5
- Mounting and operation p.5
- Maintenance and inspection p.5
- English p.5
- Applications p.5
- Symbols p.5
- English p.6
- Deutsch p.7
- Allgemeine sicherheitshinweise für elektrogeräte p.7
- Für schleif und trennschleifarbeiten geltende sicherheitshinweise p.8
- Deutsch p.8
- Weitere sicherheitshinweise zu trennschleifarbeiten p.9
- Rückschlag und dazu gehörige sicherheitshinweise p.9
- Deutsch p.9
- Besondere sicherheitshinweise für schleif bzw trennschleifarbeiten p.9
- Zusätzliche sicherheitswarnungen p.10
- Deutsch p.10
- Allgemeine sicherheitshinweise für schleifgeräte p.10
- Montage und betrieb p.11
- Deutsch p.11
- Anwendungsgebiete p.11
- Wartung und inspektion p.11
- Technische daten p.11
- Symbole p.11
- Standardzubehör p.11
- Deutsch p.12
- Français p.13
- Avertissements de sécurité généraux pour l outil p.13
- Français p.14
- Avertissements de sécurité courants pour les opérations de meulage ou de découpage par abrasion p.14
- Recul et avertissements connexes p.15
- Français p.15
- Avertissements de sécurité propres aux opérations de meulage et de découpage par abrasion p.15
- Avertissements de sécurité propres aux opérations de découpage par abrasion p.15
- Français p.16
- Consignes de sécurité générales pour les meuleuses p.16
- Avertissements de sécurité supplémentaires p.16
- Symboles p.16
- Installation et fonctionnement p.17
- Français p.17
- Entretien et vérification p.17
- Caractéristiques p.17
- Applications p.17
- Accessoires standard p.17
- Français p.18
- Italiano p.19
- Avvertimenti generali di sicurezza sugli utensili elettrici p.19
- Italiano p.20
- E il diametro esterno e lo spessore del vostro accessorio devono rientrare entro la capacità nominale dell utensile elettrico p.20
- Avvertimenti di sicurezza comuni per le operazioni di smerigliatura o di taglio abrasivo p.20
- Istruzioni di sicurezza generali per smerigliatrici p.21
- Avvertimenti di sicurezza specifici per le operazioni di smerigliatura e di taglio abrasivo p.21
- Avvertimenti di sicurezza aggiuntivi specifici per le operazioni di taglio abrasivo p.21
- Rinculo e relative avvertenze p.21
- Italiano p.21
- Simboli p.22
- Precauzioni di sicurezza aggiuntive p.22
- Italiano p.22
- Montaggio e operazione p.23
- Manutenzione ed ispezione p.23
- Italiano p.23
- Caratteristiche p.23
- Applicazioni p.23
- Accessori standard p.23
- Italiano p.24
- Nederlands p.25
- Algemene veiligheidswaarschuwingen voor elektrisch gereedschap p.25
- Veiligheidswaarschuwingen voor slijpen en doorslijpen p.26
- Nederlands p.26
- Terugslag en daarmee verband houdende waarschuwingen p.27
- Specifieke veiligheidswaarschuwingen voor slijpen en doorslijpen p.27
- Nederlands p.27
- Aanvullende specifieke veiligheidswaarschuwingen voor doorslijpen p.27
- Symbolen p.28
- Nederlands p.28
- Algemene veiligheidsinstructies voor slijpmachines p.28
- Aanvullende veiligheidswaarschuwingen p.28
- Toepassingen p.29
- Technische gegevens p.29
- Standaard toebehoren p.29
- Onderhoud en inspectie p.29
- Nederlands p.29
- Montage en gebruik p.29
- Nederlands p.30
- Advertencias de seguridad general de la herramienta eléctrica p.31
- Español p.31
- Español p.32
- Advertencias comunes de seguridad para las operaciones de molido o corte abrasivo p.32
- Retroceso y advertencias relacionadas p.33
- Español p.33
- Advertencias de seguridad específicas para las operaciones de molido y corte abrasivo p.33
- Advertencias de seguridad adicionales específicas para las operaciones de corte abrasivo p.33
- Símbolos p.34
- Instrucciones de seguridad generales para amoladoras p.34
- Español p.34
- Advertencias de seguridad adicionales p.34
- Mantenimiento e inspección p.35
- Especificaciones p.35
- Español p.35
- Aplicación p.35
- Accessorios estándar p.35
- Montaje y funcionamiento p.35
- Español p.36
- Português p.37
- Avisos gerais de segurança para a ferramenta elétrica p.37
- Recuo e avisos relacionados p.38
- Português p.38
- Avisos de segurança comuns para operações de retificação ou corte abrasivo p.38
- Português p.39
- Instruções de segurança gerais para rebarbadoras p.39
- Avisos de segurança específicos para operações de retificação ou corte abrasivo p.39
- Avisos de segurança adicionais específicos para operações de corte abrasivo p.39
- Português p.40
- Especificações p.40
- Avisos de segurança adicionais p.40
- Aplicações p.40
- Acessórios padrão p.40
- Símbolos p.40
- Português p.41
- Montagem e utilização p.41
- Manutenção e inspeção p.41
- Svenska p.42
- Allmänna säkerhetsvarningar för elektriska verktyg p.42
- Säkerhetsvarningar vanliga för slipnings eller slipande kapningsarbeten p.43
- Svenska p.43
- Kast och tillhörande varningar p.43
- Ytterligare säkerhetsvarningar för slipande kapningsarbeten p.44
- Ytterligare säkerhetsvarningar p.44
- Säkerhetsvarningar speciella för slipnings och slipande kapningsarbeten p.44
- Svenska p.44
- Allmänna säkerhetsinstruktioner för vinkelslipar p.44
- Montering och användning p.45
- Användningsområden p.45
- Underhåll och inspektion p.45
- Tekniska data p.45
- Symboler p.45
- Svenska p.45
- Standardtillbehör p.45
- Svenska p.46
- Generelle sikkerhedsadvarsler for elektrisk værktøj p.47
- Tilbageslag og relaterede advarsler p.48
- Generelle sikkerhedsadvarsler for slibning eller slibende afskæringsfunktioner p.48
- Særlige sikkerhedsforskrifter for slibning og slibende afskæringsfunktioner p.49
- Generelle sikkerhedsforskrifter for vinkelslibere p.49
- Ekstra sikkerhedsforskrifter for slibende afskæringsfunktioner p.49
- Specifikationer p.50
- Montering og anvendelse p.50
- Ekstra sikkerhedsadvarsler p.50
- Anvendelse p.50
- Symboler p.50
- Standardtilbehør p.50
- Vedligeholdelse og eftersyn p.51
- Generelle sikkerhetsforholdsregler for elektroverktøy p.52
- Tilbakeslag og relaterte advarsler p.53
- Sikkerhetsinstrukser for vanlig sliping og kutt operasjoner p.53
- Sikkerhetsinstrukser spesifikt for sliping og kutt operasjoner p.54
- Generelle sikkerhetsinstruksjoner for slipemaskiner p.54
- Flere sikkerhetsadvarsler p.54
- Ekstra sikkerhetsinstrukser spesifikt for kutt operasjoner p.54
- Vedlikehold og inspeksjon p.55
- Symboler p.55
- Standard tilbehør p.55
- Spesifikasjoner p.55
- Montering og bruk p.55
- Anvendelse p.55
- Yleiset sähkötyökalun turvallisuutta koskevat varoitukset p.57
- Turvallisuutta koskevia varoituksia hiontaa ja katkaisuhiontaa varten p.58
- Takapotku ja siihen liittyvät varoitukset p.58
- Yleisiä hiomakoneen käyttöä koskevia turvaohjeita p.59
- Turvallisuutta koskevia varoituksia erityisesti hiontaa ja katkaisuhiontaa varten p.59
- Lisää turvallisuutta koskevia varoituksia katkaisuhiontaa varten p.59
- Lisää turvallisuutta koskevia varoituksia p.59
- Tekniset tiedot p.60
- Symbolit p.60
- Sovellukset p.60
- Perusvarusteet p.60
- Kiinnittäminen ja käyttö p.60
- Huolto ja tarkastus p.60
- Ελληνικά p.62
- Γενικεσ προειδοποιησεισ ασφαλειασ του ηλεκτρικου εργαλειου p.62
- Ελληνικά p.63
- Κοινεσ προειδοποιησεισ ασφαλειασ για λειανση η εργασιεσ κοπησ p.63
- Προσθετεσ ειδικεσ προειδοποιησεισ ασφαλειασ για εργασίεσ λειανσησ η κοπησ p.64
- Οπισθια κινηση και σχετικεσ προειδοποιησεισ p.64
- Ελληνικά p.64
- Ειδικεσ προειδοποιησεισ ασφαλειασ για εργασιεσ λειανσησ η κοπησ p.64
- Προσθετεσ προειδοποιησεισ ασφαλειασ p.65
- Ελληνικά p.65
- Γενικεσ οδηγιεσ ασφαλειασ για τροχουσ p.65
- Τεχνικα χαρακτηριστικα p.66
- Συντηρηση και ελεγχοσ p.66
- Συμβολα p.66
- Στερεωση και λειτουργια p.66
- Εφαρμογεσ p.66
- Ελληνικά p.66
- Βασικα εξαρτηματα p.66
- Ελληνικά p.67
- Polski p.68
- Ogólne wskazówki bezpieczeństwa dotyczące elektronarzędzi p.68
- Polski p.69
- Ogólne wskazówki bezpieczeństwa dotyczące szlifowania i cięcia p.69
- Polski p.70
- Ogólne wskazówki bezpieczeństwa dotyczące cięcia p.70
- Odbicie i powiązane z nim ostrzeżenia p.70
- Dodatkowe wskazówki bezpieczeństwa dotyczące szlifowania i cięcia p.70
- Polski p.71
- Ogólne wskazówki bezpieczeństwa dotyczące szlifowania p.71
- Dodatkowe wskazówki bezpieczeństwa p.71
- Specyfikacje techniczne p.72
- Polski p.72
- Montaż i praca p.72
- Konserwacja i kontrola p.72
- Akcesoria standardowe p.72
- Zastosowania p.72
- Symbole p.72
- Polski p.73
- Magyar p.74
- A szerszámgéppel kapcsolatos általános biztonsági figyelmeztetések p.74
- Visszarúgás és erre vonatkozó figyelmeztetések p.75
- Magyar p.75
- Biztonsági figyelmeztetések csiszoló és vágó műveletekhez p.75
- Magyar p.76
- Csiszolókra vonatkozó általános biztonsági utasítások p.76
- A daraboló műveletekre vonatkozó kiegészítő biztonsági figyelmeztetések p.76
- A csiszolási és darabolási műveletekre vonatkozó biztonsági figyelmeztetések p.76
- Szabványos kiegészítők p.77
- Műszaki adatok p.77
- Magyar p.77
- Alkalmazási területek p.77
- További biztonsági figyelmeztetések p.77
- Szimbólumok p.77
- Összeszerelés és használat p.78
- Magyar p.78
- Karbantartás és ellenőrzés p.78
- Čeština p.79
- Obecná bezpečnostní varování týkající se bezpečnosti elektrického nánářadí p.79
- Čeština p.80
- Upozornění na zpětný ráz p.80
- Bezpečnostní varování společné pro broušení a abrazivní řezání p.80
- Čeština p.81
- Všeobecné bezpečnostní pokyny pro brusky p.81
- Doplňující bezpečnostní varování pro řezání p.81
- Bezpečnostní varování pro broušení a řezání p.81
- Montáž a provoz p.82
- Další bezpečnostní varování p.82
- Čeština p.82
- Symboly p.82
- Standardní příslušenství p.82
- Specifikace p.82
- Použití p.82
- Čeština p.83
- Údržba a kontrola p.83
- Türkçe p.84
- Genel elektri kli alet güvenli k uyarilari p.84
- Türkçe p.85
- Taşlama veya aşindirarak kesme i şlemleri i çi n genel güvenli k uyarilari p.85
- Geri tepme ve i lgi li uyarilar p.85
- Türkçe p.86
- Taşlama ve aşindirarak kesme i şlemleri i çi n özel güvenli k uyarilari p.86
- Kalipçi taşlamalar i çi n genel güvenli k tali matlari p.86
- Aşindirarak kesme i şlemleri i çi n özel i lave güvenli k uyarilari p.86
- Uygulamalar p.87
- Türkçe p.87
- Tekni k özelli kler p.87
- Standart aksesuarlar p.87
- Semboller p.87
- Montaj ve çaliştirma p.87
- I lave güvenli k uyarilari p.87
- Türkçe p.88
- Bakim ve muayene p.88
- Română p.89
- Avertismente generale privind siguranţa sculelor electrice p.89
- Română p.90
- Reculul și avertismentele aferente p.90
- Avertismente de siguranţă generale pentru operaţiunile de șlefuire sau tăiere abrazivă p.90
- Avertismente suplimentare de siguranţă specifice pentru operaţiunile tăiere abrazivă p.91
- Avertismente de siguranţă specifice pentru operaţiunile de șlefuire și tăiere abrazivă p.91
- Română p.91
- Instrucţiuni generale de siguranţă pentru polizoare p.91
- Specificaţii p.92
- Simboluri p.92
- Română p.92
- Avertismente suplimentare privind siguranţa p.92
- Asamblare și operare p.92
- Aplicaţii p.92
- Accesorii standard p.92
- Întreţinere și verificare p.93
- Română p.93
- Splošna varnostna navodila za električna orodja p.94
- Slovenščina p.94
- Varnostna opozorila značilna za brušenje ali rezanje p.95
- Slovenščina p.95
- Povratni udarec in ustrezna opozorila p.95
- Varnostna opozorila za brušenje in rezanje p.96
- Splošna varnostna navodila za brusilnike p.96
- Slovenščina p.96
- Dodatna varnostna opozorila za rezanje p.96
- Dodatna varnostna opozorila p.96
- Vzdrževanje in pregledovanje p.97
- Uporaba p.97
- Standardna pribor p.97
- Specifikacije p.97
- Slovenščina p.97
- Simboli p.97
- Namestitev in delovanje p.97
- Slovenščina p.98
- Všeobecné bezpečnostné výstrahy pre elektrické náradie p.99
- Slovenčina p.99
- Bezpečnostné výstrahy spoločné pre činnosti brúsenia a rozbrusovania p.100
- Spätný náraz a príslušné varovania p.100
- Slovenčina p.100
- Všeobecné bezpečnostné pokyny pre brúsky p.101
- Slovenčina p.101
- Dodatočné bezpečnostné výstrahy charakteristické pre činnosti brúsenia a rozbrusovania p.101
- Bezpečnostné výstrahy charakteristické pre činnosti brúsenia a rozbrusovania p.101
- Štandardné príslušenstvo p.102
- Ďalšie bezpečnostné varovania p.102
- Technické parametre p.102
- Symboly p.102
- Slovenčina p.102
- Použitie p.102
- Údržba a kontrola p.103
- Slovenčina p.103
- Montáž a obsluha p.103
- Български p.104
- Общи мерки за безопасност при използване на електрически инструменти p.104
- Предупреждения за безопасност общи за операции включващи шлифоване или абразивно рязане p.105
- Български p.105
- Предупреждения за откат и свързани с това опасности p.106
- Предупреждения за безопасност специфични за операции включващи шлифоване или абразивно рязане p.106
- Допълнителни предупреждения за безопасност специфични за операции включващи абразивно рязане p.106
- Български p.106
- Общи инструкции за безопасност за шлайфмашини p.107
- Допълнителни предупреждения за безопасност p.107
- Български p.107
- Спецификации p.108
- Символи p.108
- Приложения p.108
- Поддръжка и инспекция p.108
- Монтаж и експлоатация p.108
- Български p.108
- Стандартни аксесоари p.108
- Български p.109
- Srpski p.110
- Opšta bezbednosna upozorenja za električni alat p.110
- Srpski p.111
- Povratni udar i slična upozorenja p.111
- Bezbednosna upozorenja za postupke brušenja ili abrazivnog sečenja p.111
- Srpski p.112
- Opšta bezbednosna uputstva za brusilice p.112
- Dodatna bezbednosna upozorenja specifična za postupke abrazivnog sečenja p.112
- Bezbednosna upozorenja specifična za postupke brušenja i abrazivnog sečenja p.112
- Specifikacije p.113
- Primene p.113
- Oznake p.113
- Montaža i upotreba p.113
- Dodatna bezbednosna upozorenja p.113
- Standardni pribor p.113
- Srpski p.113
- Srpski p.114
- Održavanje i provera p.114
- Općenita sigurnosna upozorenja za električne alate p.115
- Hrvatski p.115
- Sigurnosna upozorenja za sve operacije brušenja ili abrazivnog rezanja p.116
- Povratni udar i povezana upozorenja p.116
- Hrvatski p.116
- Sigurnosna upozorenja specifična za operacije brušenja i abrazivnog rezanja p.117
- Opće sigurnosne upute za brusilice p.117
- Hrvatski p.117
- Dodatna sigurnosna upozorenja specifična za operacije abrazivnog rezanja p.117
- Dodatna sigurnosna upozorenja p.117
- Montaža i rad p.118
- Hrvatski p.118
- Vrste primjene p.118
- Standardna oprema p.118
- Specifikacije p.118
- Simboli p.118
- Održavanje i inspekcija p.118
- Hrvatski p.119
- Українська p.120
- Загальні інструкції безпеки електричного інструменту p.120
- Українська p.121
- Загальні попередження про обережність для проведення шліфувальних робіт або відрізання p.121
- Українська p.122
- Заходи безпеки під час шліфування і абразивного обрізування p.122
- Додаткові заходи безпеки спеціально для абразивного різання p.122
- Віддача і пов язані з нею небезпеки p.122
- Загальні інструкції безпеки для шліфувальної машини p.123
- Додаткові правила безпеки p.123
- Українська p.123
- Символи p.123
- Установка та експлуатація p.124
- Українська p.124
- Технічні характеристики p.124
- Технічне обслуговування і перевірка p.124
- Стандартні аксесуари p.124
- Області застосування p.124
- Українська p.125
- Русский p.126
- Общие правила безопасности при работе с электроинструментом p.126
- Русский p.127
- Общие предупреждения об осторожности для проведения шлифовальных работ или отрезания p.127
- Русский p.128
- Отдача и другие похожие предупреждения p.128
- Особые меры предосторожности для режущих работ и абразивной отрезки p.128
- Русский p.129
- Общие инструкции по технике безопасности для шлифовальных машин p.129
- Дополнительные особые меры предосторожности для абразивной отрезки p.129
- Стандартные принадлежности p.130
- Символы p.130
- Русский p.130
- Дополнительные указания по обеспечению безопасности p.130
- Установка и эксплуатация p.131
- Техническое обслуживание и осмотр p.131
- Технические характеристики p.131
- Русский p.131
- Назначение p.131
- Русский p.132
- Garantni sertifikat p.139
- Certificado de garantía p.139
- Garantisertifikat p.139
- Certificado de garantia p.139
- Гаранционен сертификат p.139
- Garantieschein p.139
- Book_g10sr4 indb 139 0000book_g10sr4 indb 139 2016 01 29 19 00 10 2016 01 29 19 00 10 p.139
- Гарантійний сертифікат p.139
- Garantiebewijs p.139
- Гарантийный сертификат p.139
- Garanticertifikat p.139
- Garantibevis p.139
- Πιστοποιητικο εγγυησησ p.139
- Garanti serti fi kasi p.139
- Záručný lista p.139
- Garancijsko potrdilo p.139
- Záruční list p.139
- Garancia bizonylat p.139
- Takuutodistus p.139
- Français suomi slovenčina p.139
- Svenska türkçe русский p.139
- Español magyar hrvatski p.139
- Português čeština український p.139
- Nederlands polski srpski p.139
- English dansk română p.139
- Jamstveni certifikat p.139
- Deutsch norsk slovenščina p.139
- Italiano ελληνικά български p.139
- Certificato di garanzia p.139
- Gwarancja p.139
- Certificat de garanţie p.139
- Guarantee certificate p.139
- Certificat de garantie p.139
- Hitachi power tools belgium n v s a p.141
- Hitachi fercad power tools italia s p a p.141
- Hitachi power tools österreich gmbh p.141
- Hitachi power tools u k ltd p.141
- Hitachi power tools sweden ab p.141
- Hitachi power tools romania s r l p.141
- Hitachi power tools polska sp z o o p.141
- Hitachi power tools norway as p.141
- Hitachi power tools netherlands b v moscow branch p.141
- Hitachi power tools netherlands b v p.141
- Hitachi power tools lberica s a p.141
- Hitachi power tools hungary kft p.141
- Hitachi power tools france s a s p.141
- Hitachi power tools finland oy p.141
- Hitachi power tools europe gmbh p.141
- Hitachi power tools denmark a s p.141
- Hitachi power tools czech s r o p.141
- Deutsch español p.142
- Representative offi ce in europe hitachi power tools europe gmbh siemensring 34 47877 willich 1 f r germany p.142
- M harada executive offi cer p.142
- John de loughry european standard manager p.142
- Italiano svenska p.142
- Hitachi koki europe ltd clonshaugh business technology park dublin 17 lreland p.142
- Head offi ce in japan hitachi koki co ltd shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan p.142
- Français português p.142
- English nederlands p.142
- Suomi čeština p.143
- Representative offi ce in europe hitachi power tools europe gmbh siemensring 34 47877 willich 1 f r germany p.143
- Norsk magyar p.143
- M harada executive offi cer p.143
- John de loughry european standard manager p.143
- Hitachi koki europe ltd clonshaugh business technology park dublin 17 lreland p.143
- Head offi ce in japan hitachi koki co ltd shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan p.143
- Dansk polski p.143
- Ελληνικά türkçe p.143
- Български русский p.144
- Slovenščina hrvatski p.144
- Slovenčina український p.144
- Română srpski p.144
- Representative offi ce in europe hitachi power tools europe gmbh siemensring 34 47877 willich 1 f r germany p.144
- M harada executive offi cer p.144
- John de loughry european standard manager p.144
- Hitachi koki europe ltd clonshaugh business technology park dublin 17 lreland p.144
- Head offi ce in japan hitachi koki co ltd shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan p.144
- Code no c99714073 na printed in china p.144
Похожие устройства
-
Hitachi G23SW-NPИнструкция по эксплуатации -
Hitachi G13SN-NUИнструкция по эксплуатации -
Hitachi G23SR-NSИнструкция по эксплуатации -
Hitachi G13SD-NSИнструкция по эксплуатации -
Hitachi G13SS-NUИнструкция по эксплуатации -
Hitachi G18ST-NUИнструкция по эксплуатации -
Hitachi G23MRU-NBИнструкция по эксплуатации -
Hitachi G12SW-NSИнструкция по эксплуатации -
Hitachi G23ST-NUИнструкция по эксплуатации -
Hitachi G18ST-NSИнструкция по эксплуатации -
Hitachi G23SRU-NSИнструкция по эксплуатации -
Hitachi G13YD-LAИнструкция по эксплуатации
Learn crucial safety warnings for using grinding and cutting tools. Follow these guidelines to prevent injuries and ensure safe operation of power tools.