Bort BWS-1000-R 98296631 [11/40] Kickback and related warnings
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Bort BWS-1000-R 98296631 [11/40] Kickback and related warnings

Bort BWS-1000-R 98296631 [11/40] Kickback and related warnings
11
• Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations dierent from
those intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualied repair person
using only identical replacement parts. This will ensure
that the safety of the power tool is maintained.
SAFETY WARNINGS FOR ANGLE GRINDER
• This power tool is intended to function as a grinder,
sander, wire brush or cut-o tool. Read all safety warn-
ings, instructions, illustrations and specications pro-
vided with this power tool. Failure to follow all instruc-
tions listed below may result in electric shock, re and/
or serious injury.
• Operations such as polishing are not recommended to
be performed with this power tool. Operations for which
the power tool was not designed may create a hazard
and cause personal injury.
• Do not use accessories which are not specically de-
signed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
• The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can
break and y apart.
• The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power
tool. Incorrectly sized accessories cannot be adequately
guarded or controlled.
• Threaded mounting of accessories must match the grind-
er spindle thread. For accessories mounted by anges,
the arbour hole of the accessory must t the locating
diameter of the ange. Accessories that do not match the
mounting hardware of the power tool will run out of bal-
ance, vibrate excessively and may cause loss of control.
• Do not use a damaged accessory. Before each use in-
spect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess wear,
wire brush for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or install an
undamaged accessory. After inspecting and installing an
accessory, position yourself and bystanders away from
the plane of the rotating accessory and run the power
tool at maximum no-load speed for one minute. Dam-
aged accessories will normally break apart during this
test time.
• Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing protec-
tors, gloves and shop apron capable of stopping small
abrasive or workpiece fragments. The eye protection
must be capable of stopping ying debris generated by
various operations. The dust mask or respirator must be
capable of ltrating particles generated by your opera-
tion. Prolonged exposure to high intensity noise may
cause hearing loss.
• Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a
broken accessory may y away and cause injury beyond
immediate area of operation.
• Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting acces-
sory may contact hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
• Position the cord clear of the spinning accessory. If you
lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning wheel.
• Never lay the power tool down until the accessory has
come to a complete stop. The spinning wheel may grab
the surface and pull the power tool out of your control.
• Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your body.
• Regularly clean the power tool’s air vents. The motor’s
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
• Do not operate the power tool near ammable materi-
als. Sparks could ignite these materials.
• Do not use accessories that require liquid coolants. Us-
ing water or other liquid coolants may result in electro-
cution or shock.
Kickback and related warnings
• Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other acces-
sory. Pinching or snagging causes rapid stalling of the
rotating accessory which in turn causes the uncontrolled
power tool to be forced in the direction opposite of
the accessory’s rotation at the point of the binding. For
example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is enter-
ing into the pinch point can dig into the surface of the
material causing the wheel to climb out or kick out. The
wheel may either jump toward or away from the opera-
tor, depending on direction of the wheel’s movement at
the point of pinching. Abrasive wheels may also break
under these conditions. Kickback is the result of power
tool misuse and/or incorrect operating procedures or
conditions and can be avoided by taking proper precau-
tions as given below.
• Maintain a rm grip on the power tool and position your
body and arm to allow you to resist kickback forces.
Always use auxiliary handle, if provided, for maximum
control over kickback or torque reaction during start-up.
The operator can control torque reactions or kickback
forces, if proper precautions are taken.
• Never place your hand near the rotating accessory. Ac-
cessory may kickback over your hand.
• Do not position your body in the area where power tool
will move if kickback occurs. Kickback will propel the
tool in direction opposite to the wheel’s movement at
the point of snagging.

Содержание

Похожие устройства

Скачать