Hitachi G23SR-NS [7/68] Safety warnings common for grinding or abrasive cutting off operations
![Hitachi G 23SRU [7/68] Safety warnings common for grinding or abrasive cutting off operations](/views2/1081392/page7/bg7.png)
6
English
SAFETY WARNINGS COMMON FOR
GRINDING OR ABRASIVE CUTTING-OFF
OPERATIONS
a) This power tool is intended to function as a grinder
or cut-off tool. Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
b) Operations such as sanding, wire brushing or
polishing are not recommended to be performed
with this power tool.
Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
c) Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Accessories running faster than their rated speed
can break and fly apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) The arbour size of wheels, flanges, backing pads
or any other accessory must properly fit the spindle
of the power tool.
Accessories with arbour holes that do not match
the mounting hardware of the power tool will run
out of balance, vibrate excessively and may cause
loss of control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute.
Damaged accessories will normally break apart
during this test time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping flying
debris generated by various operations. The dust
mask or respirator must be capable of filtrating particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a broken accessory
may fly away and cause injury beyond immediate
area of operation.
j) Hold power tool by insulated gripping surfaces only,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a”live” wire may make
exposed metal parts of the power tool “live” and
shock the operator.
k) Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the
spinning accessory.
l) Never lay the power tool down until the accessory
has come to a complete stop.
The spinning accessory may grab the surface and
pull the power tool out of your control.
m) Do not run the power tool while carrying it at your
side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your
body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal may
cause electrical hazards.
o) Do not operate the power tool near flammable
materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power
tool to be forced in the direction opposite of the accessory’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may
either jump toward or away from the operator, depending
on direction of the wheel’s movement at the point of
pinching. Abrasive wheels may also break under these
conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below.
a) Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up.
The operator can control torque reactions or kickback
forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power
tool will move if kickback occurs.
Kickback will propel the tool in direction opposite
to the wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
01Eng_G18SH2_EE 11/30/09, 18:496
Содержание
- ㅃ潶敲彇ㄸ午㉟䕅 p.1
- K l n m p.2
- 䵡牫彇ㄸ午㉟䕅 p.2
- Bceöàa ìaàeçaèúe cpeàcúça áaçëúê öîaá p.5
- Olvasson el minden biztonsági figyelmeztetést és minden utasítást a figyelmeztetések és utasítások be nem tartása áramütést tüzet és vagy súlyos sérülést eredményezhet p.5
- Mindig viseljen védőszemüveget p.5
- Jelölések p.5
- Φ ράτε πάντα τ ν κατάλληλ ε πλισµ για την πρ στασία των µατιών p.5
- Figyelem p.5
- Ì ôï p.5
- Dókkat p.5
- Zawsze nosić okulary ochronne p.5
- Daima koruyucu gözlük takın p.5
- Warnung p.5
- Cëïçoîê p.5
- Warning p.5
- Csak eu országok számára az elektromos kéziszerszámokat ne dobja a háztartási szemétbe a használt villamos és elektronikai készülékekről szóló 2002 96 ek irányelv és annak a nemzeti jogba való átültetése szerint az elhasznált elektromos kéziszerszámokat külön kell gyűjteni és környezetbarát módon újra kell hasznosítani p.5
- Vždy noste ochranu očí p.5
- Always wear eye protection tragen sie immer einen augenschutz p.5
- Upozornění p.5
- Symboly p.5
- Symbols p.5
- Symbole p.5
- Simgeler p.5
- Sadece ab ülkeleri için elektrikli el aletlerini evdeki çöp kutusuna atmayınız kullanılmıß elektrikli aletleri elektrik ve elektronikli eski cihazlar hakkındaki 2002 96 ec avrupa yönergelerine göre ve bu yönergeler ulusal hukuk kurallarına göre uyarlanarak ayrı olarak toplanmalı ve çevre ßartlarına uygun bir ßekilde tekrar deåerlendirmeye gönderilmelidir p.5
- Ostrzeżenie p.5
- 〱䕮束䜱㡓䠲彅 p.6
- General power tool safety warnings p.6
- English p.6
- Safety warnings common for grinding or abrasive cutting off operations p.7
- Kickback and related warnings p.7
- English p.7
- Safety warnings specific for grinding and abrasive cutting off operations p.8
- Precautions on using disc grinder p.8
- English p.8
- Additional safety warnings specific for abrasive cutting off operations p.8
- Standard accessories p.9
- Specifications p.9
- Prior to operation p.9
- English p.9
- Applications p.9
- Practical grinder application p.10
- Maintenance and inspection p.10
- English p.10
- Assembling and disassembling the depressed center wheel p.10
- Guarantee p.11
- English p.11
- 〲䝥牟䜱㡓䠲彅 p.12
- Deutsch p.12
- Allgemeine sicherheitshinweise für elektrogeräte p.12
- Für schleif und trennschleifarbeiten geltende sicherheitshinweise p.13
- Deutsch p.13
- Weitere sicherheitshinweise zu trennschleifarbeiten p.14
- Rückschlag und dazu gehörige sicherheitshinweise p.14
- Deutsch p.14
- Besondere sicherheitshinweise für schleif bzw trennschleifarbeiten p.14
- Vor inbetriebnahme p.15
- Technische daten p.15
- Standardzubehör p.15
- Deutsch p.15
- Anwendungsgebiete p.15
- Vorsichtsmassnahmen bei der benutzung des winkelschleifers p.15
- Praktische schleifarbeit p.16
- Deutsch p.16
- Wartung und inspektion p.17
- Garantie p.17
- Deutsch p.17
- Anbringen und abnehmen der schleifscheibe p.17
- Deutsch p.18
- 〳䝲敟䜱㡓䠲彅 p.19
- Π ƒ π π π º π ƒπ à ƒ π à p.19
- Ïïëóèî p.19
- Ƒ π π π º π π π ƒ ãπ ª ƒ ãà ƒπ π ª p.20
- Ïïëóèî p.20
- Ƒ π π π º π π π π ƒ ãπ ª ƒ ãà ƒπ π ª p.21
- Ƒ ƒ π π π º π π π π ƒ ãπ ª ƒ ãà ƒπ π ª p.21
- Ïïëóèî p.21
- Π ª π ã π ƒ π π π p.21
- Π ƒ ª p.22
- Ƒπ π àƒ π p.22
- Ƒ ºà π ª ƒ ø ムà π à π p.22
- Ïïëóèî p.22
- Ã π ã ƒ ƒπ π p.22
- º ƒª p.22
- Ƒ π º ƒª à π p.23
- Ïïëóèî p.23
- Ïïëóèî p.24
- À ƒª π à ƒª à ã ª øª à ƒπ ƒ ã à p.24
- À ƒ π ã p.24
- Ïïëóèî p.25
- 〴偯江䜱㡓䠲彅 p.26
- Polski p.26
- Ogólne wskazówki bezpieczeństwa dotyczące urządzeń elektrycznych p.26
- Polski p.27
- Ogólne wskazówki bezpieczeństwa dotyczące prac szlifierskich i cięcia p.27
- Wskazówki bezpieczeństwa dotyczące szlifowania i ścierania p.28
- Polski p.28
- Ostrzeżenia dotyczące odrzutu oraz podobnych zagrożeń p.28
- Dodatkowe wskazówki bezpieczeń stwa dotyczące prac związanych z przecinaniem p.28
- Środki ostrożności przy używaniu szlifierki tarczowej p.29
- Zastosowanie p.29
- Wyposażenie standardowe p.29
- Przed użyciem p.29
- Polski p.29
- Dane techniczne p.29
- Składanie i rozkładanie obniżonych tarcz śsrodkowych p.30
- Praktyczne zastosowanie szlifierki p.30
- Polski p.30
- Gwarancja p.31
- Polski p.31
- Konserwacja i inspekcja p.31
- 〵䡵湟䜱㡓䠲彅 p.32
- Szerszámgépekre vonatkozó általános biztonsági figyelmeztetések p.32
- Magyar p.32
- Magyar p.33
- Biztonsági figyelmeztetések csiszoló és vágó műveletekhez p.33
- Visszarúgás és az arra vonatkozó figyelmeztetések p.34
- Magyar p.34
- Kiegészítő biztonsági figyelmeztetések a daraboló műveletre vonatkozóan p.34
- Biztonsági figyelmeztetések csiszolásra és a darabolási folyamatra vonakozóan p.34
- A tárcsás kéziköszörű használatára vonatkozó óvintézkedések p.34
- Magyar p.35
- Az üzembehelyezés előtti tennivalók p.35
- Alkalmazások p.35
- A kéziköszörű gyakorlati kezelése p.35
- Műszaki adatok p.35
- Magyar p.36
- Ellenőrzés és karbantartás p.36
- A süllyesztett közepű tárcsa összeszerelése és szétszerelése p.36
- Magyar p.37
- Garancia p.37
- 䍺敟䜱㡓䠲彅 p.38
- Čeština p.38
- Obecná varování týkající se bezpečnosti el přístroje p.38
- Čeština p.39
- Kopnutí a s tím související varování p.39
- Bezpečnostní varování společná pro broušení a odřezávání p.39
- Čeština p.40
- Upozornění pro používání kotoučové brusky p.40
- Dodatečná bezpečnostní varování specifická pro řezání p.40
- Bezpečnostní varování specifická pro broušení a řezání p.40
- Čeština p.41
- Standardní příslušenství p.41
- Před použitím p.41
- Praktické použití brusky p.41
- Použití p.41
- Parametry p.41
- Čeština p.42
- Údržba a kontrola p.42
- Montáž a demontáž brusného kotouče p.42
- Čeština p.43
- Záruka p.43
- 呵牟䜱㡓䠲彅 p.44
- Türkçe p.44
- Genel elektrókló alet güvenlók uyarilari p.44
- Taílama veya aíindirarak kesme óílemleró óçón genel güvenlók uyarilari p.45
- Geró tepme ve ólgóló uyarilar p.45
- Türkçe p.45
- Türkçe p.46
- Taílama ve aíindirarak kesme óílemleró óçón özel güvenlók uyarilari p.46
- Dósk taílama aletónó kullanirken alinacak önlemler p.46
- Aíindirarak kesme óílemleró óçón özel ólave güvenlók uyarilari p.46
- Uygulamalar p.47
- Türkçe p.47
- Teknók özellókler p.47
- Standart aksesuarlar p.47
- Pratók taílama uygulamalari p.47
- Aletó kullanim öncesónde p.47
- Türkçe p.48
- Tek tarafi oyuk taílama dóskónón takilip çikarilmasi p.48
- Bakim ve ónceleme p.48
- Türkçe p.49
- Garantó p.49
- 〸創獟䜱㡓䠲彅 p.50
- Pyccíëè p.50
- Oåôàe èpabàãa åeâoèachoctà èpà paåote c ùãektpoàhctpìmehtom p.50
- Pyccíëè p.51
- Oåôàe èpeñyèpeüñehàü oå octopoühoctà ñãü èpobeñehàü òãàîobaãúhõx paåot àãà otpeâahàü p.51
- Pyccíëè p.52
- Otñaóa à ñpìéàe èoxoüàe èpeñìèpeüñehàü p.52
- Ocoåõe mepõ èpeñoctopoühoctà ñãü peüìôàx paåot à aåpaâàbhoâ otpeâkà p.52
- Pyccíëè p.53
- Ñoèoãhàteãúhõe ocoåõe mepõ èpeñoctopoühoctà ñãü aåpaâàbhoâ otpeâkà p.53
- Mepõ èpeñoctopoühoctà èpà ùkcèãìatañàà òãàîobaãúhoâ maòàhõ p.53
- Èoñéotobka k ùkcèãìatañàà p.54
- Texhàóeckàe xapaktepàctàkà p.54
- Pyccíëè p.54
- Oåãactú èpàmehehàü p.54
- Ctahñapthõe akceccìapõ p.54
- Ìctahobka à chütàe òãàîobaãúhoéo kpìéa c ìtoèãehhõm ñehtpom p.55
- Èpaktàóeckoe èpàmehehàe òãàîobaãúhoâ maòàhõ p.55
- Pyccíëè p.55
- Éapahtàü p.56
- Texhàóeckoe oåcãìüàbahàe à èpobepka p.56
- Pyccíëè p.56
- Pyccíëè p.57
- 〹䉡捫彇ㄸ午㉟䕅 p.58
- G18sh2 p.58
- G23sf2 p.59
- G18sru p.60
- G23sru p.61
- Hitachi power tools polska sp z o o p.67
- Hitachi power tools netherlands b v moscow branch p.67
- Hitachi power tools hungary kft p.67
- Hitachi power tools czech s r o p.67
- Hitachi power tools österreich gmbh p.67
- Hitachi power tools romania p.67
- Technical file at p.68
- Siemensring 34 47877 willich 1 f r germany p.68
- Shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan p.68
- Representative office in europe p.68
- K kato board director p.68
- Hitachi power tools europe gmbh p.68
- Hitachi koki europe ltd p.68
- Hitachi koki co ltd p.68
- Head office in japan p.68
- Code no c99107295 e printed in ireland p.68
- Clonshaugh business technology park dublin 17 lreland p.68
Похожие устройства
-
Hitachi G23SW-NPИнструкция по эксплуатации -
Hitachi G13SN-NUИнструкция по эксплуатации -
Hitachi G13SD-NSИнструкция по эксплуатации -
Hitachi G13SS-NUИнструкция по эксплуатации -
Hitachi G18ST-NUИнструкция по эксплуатации -
Hitachi G23MRU-NBИнструкция по эксплуатации -
Hitachi G12SW-NSИнструкция по эксплуатации -
Hitachi G23ST-NUИнструкция по эксплуатации -
Hitachi G18ST-NSИнструкция по эксплуатации -
Hitachi G23SRU-NSИнструкция по эксплуатации -
Hitachi G13YD-LAИнструкция по эксплуатации -
Hitachi G23UCY-NSИнструкция по эксплуатации