Home
Главная
Makita
Сетевая эксцентриковая шлифовальная машина
BO5041K
Инструкция по эксплуатации Страница: 6

Makita BO5041K [6/40] Assembly

ASSEMBLY

CAUTION:

•

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

How to use the front grip

Fig.3

The front grip can be loosened and moved horizontally to

a desired working position. Once the front grip is in the

desired position, retighten before using.

Installing or removing the front grip

Fig.4

Open the grip base, and attach it to the sander in the

area of the Makita logo.

Fig.5

After closing the grip base, firmly tighten on the front grip

to the screw section of the grip base.

Fig.6

To remove, loosen and remove front grip, and then

remove grip base.

Installing or removing abrasive disc

Fig.7

To install the abrasive disc, first remove all dirt or foreign

matter from the pad. Then peel off the backing paper

from the abrasive disc and attach the abrasive disc to the

pad. Be careful to align the holes in the abrasive disc with

those in the pad.

CAUTION:

• If you peel off the abrasive disc from the pad, its

adhesion will become poor. Never attempt to stick it

onto the pad for further use.

Installing dust bag

Fig.8

Install the dust bag on the tool so that the Makita logo on

the dust bag will be upright (not upside down).

Emptying dust bag

Fig.9

When the dust bag is about half full, switch off and unplug

the tool. Remove the dust bag from the tool. Then remove

the dust nozzle from the dust bag after unlocking the dust

nozzle by turning it slightly counterclockwise. Empty the

dust bag by tapping it lightly.

Fig.10

After emptying the dust bag, install the dust nozzle on the

dust bag. Turn the dust nozzle slightly clockwise to lock it

in place. Then install the dust bag on the tool as

described in "Installing dust bag".

Installing paper dust bag

Fig.11

Place the paper dust bag on the paper dust bag holder

with its front side upward. Insert the front fixing cardboard

of the paper dust bag into the groove of the paper dust

bag holder.

Fig.12

Then press the upper part of the front fixing cardboard in

arrow direction to hook it onto the claws.

Fig.13

Fig.14

Insert the notch of the paper dust bag into the guide of

the paper dust bag holder. Then install the paper dust

bag holder set on the tool.

Installing paper filter bag

Fig.15

Make sure that the logo on the cardboard lip and the logo

on the dust box are on the same side, then install the

paper filter bag by fitting the cardbord lip in the groove of

each holding tab.

Fig.16

Make sure that the logo on the cardboard lip and the logo

on the dust nozzle are on the same side, then install the

dust nozzle on the dust box.

Removing dust box and paper filter bag

Fig.17

Remove the dust nozzle by pushing the two latches.

Fig.18

Remove the paper filter bag first by pinching the logo

side of its cardboard lip, then by pulling the cardboard lip

downwards to move it out of the holding tab of the dust

box.

OPERATION

CAUTION:

• Always use the front grip and firmly hold the tool by

front grip and switch handle during operations.

Sanding operation

Fig.19

CAUTION:

• Never run the tool without the abrasive disc. You

may seriously damage the pad.

• Never force the tool. Excessive pressure may

decrease the sanding efficiency, damage the

abrasive disc or shorten tool life.

• Using the tool with the pad edge contacting the

workpiece may damage the pad.

Hold the tool firmly. Turn the tool on and wait until it

attains full speed. Then gently place the tool on the

workpiece surface. Keep the pad flush with the

workpiece and apply slight pressure on the tool.

CAUTION:

The sanding pad rotates clockwise during the loaded

operation, but it may rotate counterclockwise during the

no-load operation.

Makita BO5041K [6/40] Assembly

Содержание

Похожие устройства