Home
Главная
Vitek
Мультиварки
VT-4209
Инструкция по эксплуатации Страница: 10

Vitek VT-4209 [10/72] English

ENGLISH

– Do not compact dry ingredients when putting them into the measuring cup (22).

– It is important to screen the flour before measuring in order to saturate it with

air, this provides the best baking quality. The heap should be removed with a

knife.

INGREDIENTS LOADING

– The following order of ingredients loading is recommended (unless otherwise is

specified in the recipe): liquids (water, milk, oil, whipped eggs, etc.). are poured

on the bottom of the baking form (2), dry ingredients are fed afterwards, yeast

powder is added last.

– See that flour does not become completely wet, put yeast in dry flour only. Yeast

should not come in contact with salt before kneading as salt reduces yeast

capacity.

– When using the delay function do not put perishable foods – for example, eggs,

fruit, milk – into the form (2).

Attention!

All recipes are non-regulatory as the required amount and proportions of the

ingredients may vary depending on local peculiarities of the food and altitude

above sea level.

PROBLEMS DURING BREAD BAKING

The dough rises too quickly Excessive quantity of yeast, flour or insufficient quantity of salt

The bread won’t rise

Not enough yeast

Old or inactive yeast

Yeast came in contact with liquid ingredients or salt before kneading

Wrong selection of flour sort, or flour is of poor quality

Not enough sugar

Soft water leads to more active yeast growth

Intensive dough rising, dough gets out of the baking form

Excessive quantity of yeast or flour

Excessive quantity of dough

Bread dropped in the middle

Yeast growth is poor because of high temperature the liquid or its excessive quantity

Excessive quantity of flour or lack of liquid

Dense crumb, clumps

Not enough yeast and sugar

Excessive quantity of fruit, whole grains, etc.

Flour of poor quality

Excessive liquid temperature leads to quick yeast growth and early dough dropping

No salt or not enough sugar

Lack of flour

Bread is slack-baked in the middle

Using much liquid and liquid ingredients (for example, yoghurt)

Excessive quantity of liquid ingredients

Coarse crumb

No salt

Water is too hot

Excessive quantity of dough

Bread surface is slack-baked

Excessive quantity of flour (especially when you are making wheat bread)

Excessive quantity of yeast or lack of salt

Excessive quantity of sugar

Other sweet ingredients besides sugar are used

Crumb of cut bread pieces is grainy and non-uniform You have not cooled the bread down before cutting (excessive moisture did not have time to evaporate)

ADDITIONAL FUNCTIONS

Memory

– In case of emergency power cutoff during the operation process the memory

function with the duration of up to 7 minutes is activated.

– If the power supply is restored within 7 minutes unit will continue to perform the

pre-set program from the moment it has been stopped at.

– If there is no power for more than 7 minutes it is necessary to load the ingredients

again and program the unit.

CLEANING AND CARE

– At the end of operation, switch the unit off, unplug the power cord from the mains

socket and disconnect the power cord from the connector (16), located on the

multi-cooker body (5).

– Wait till the unit cools down.

– Clean the unit body (5) and lid (9) with a slightly damp cloth, and then wipe dry.

– Wash all removable parts with warm water and a neutral detergent.

Note: - If the paddle (4) can not be removed from the axle, fill the form (2) with

warm water and wait for about 30 minutes.

– Dry removable parts thoroughly, after that you can install them in the process

chamber.

– Do not immerse the unit body, power cord and cord plug into water and other

liquids.

STORAGE

– Before storage clean the bread maker and wait till it is completely dry.

– Keep the unit in a dry cool place out of reach of children and disabled persons.

TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

Symbols «E01» appeared on the display,

accompanied by repeated sound signals

The unit has not cooled down after the previous

baking cycle

Unplug the unit, take the form out, let the unit cool down at

room temperature

Symbols «Еrr» on the display, accompanied by

repeated sound signals

Improper placement of the baking form (2)

Switch the unit off, open the lid, place the baking form and

turn it clockwise until it is fixed.

VT-4209_A4_NEV.indd 10 18.11.2013 9:42:54

Vitek VT-4209 [10/72] English

Содержание

Похожие устройства