![Airwell MQL 15 [16/40] English](/img/pdf.png)
Airwell MQL 15 [16/40] English
![Airwell MQH 10T [16/40] English](/views2/1409105/page16/bg10.png)
4.7 Power supply
Before carrying out any operations on the
electrical system, make sure that the unit is
deenergised.
It is important that the appliance is ground-
ed.
The company in charge of the installation
shall conform to the standards applicable to
outdoor electrical connections.
Itelco-Clima may not be held liable for any damage
and/or injury caused by failure to comply with these
precautions.
The unit conforms to EN 60204-1.
The following connections shall be provided:
h
A link for the power supply and the earth connec-
tion
h
The electrical distribution system shall meet the
power absorbed by the appliance.
h
The disconnecting and magnetothermal switches
must be sized to control the starting current of the
unit.
h
The power supply lines and the insulation devices
must be designed in such a way that every line in-
dependent.
h
It is recommended to install differential switches,
to prevent any damage caused by phase drops.
h
The fans and compressors are supplied through
contactors controlled from the control panel.
h
Each motor is provided with an internal safety
thermal device and external fuses.
h
The power supply cables must be inserted into
dedicated openings on the front of the unit, and
the will enter the electrical board through holes
drilled on the bottom of the board.
Page 15
English
Installation
4.8 Electrical connections
The unit must be installed on site according to the
Machinery Directive (98/37/EC), the Low Voltage Di-
rective (73/23/EC), the Electromagnetic Interference
Directive (89/336/EC) and the usual procedures and
standards applicable in the place of installation. The
unit must not be operated if its installation has not
been carried out according to the instructions provid-
ed in this manual.
The power supply lines must consist of insulated cop-
per conductors, dimensioned for the maximum ab-
sorbed current.
Connection to terminals must be performed accord-
ing to the diagram of connections provided in this
manual and according to the wiring diagram which
accompanies the unit.
Before connecting the power supply lines,
check that the available voltage value does
not exceed the range specified in the Elec-
tric Data (Chapter 8).
For 3-phase systems, check also that the unbalance
between the phases does not exceed 2%. To perform
this check, measure the differences between the volt-
age of each phase couple and their mean value dur-
ing operation. The maximum % value of these differ-
ences (unbalance) must not exceed 2% of the mean
voltage. If the unbalance is unacceptable, contact
the Energy Distributor to solve this problem.
Supplying the unit through a line whose un-
balance exceeds the permissible value will
automatically void the warranty.
It’s recommended to check the correct se-
quence of the three supply phases R-S-T- be-
fore the unit start up.
Manuale MQL-MQH 10.6.2005 12:26 Pagina 15
Содержание
- Mql mqh 4 17 1
- Dismantling demolition and scrapping 2
- English 2
- Foreword 2
- General description 2
- Installation 2
- Maintenance 2
- Minichiller control 2
- Safety 2
- Spare parts 2
- Start up 2
- Table of contents 2
- Technical data 2
- Transport lifting and positioning 2
- Troubleshooting 2
- An introduction to the manual 3
- Emergency stop normal stop 3
- Foreword 3
- Introduction 3
- Warranty 3
- Definitions 4
- English 4
- Foreword 4
- Safety 4
- Access to the unit 5
- General precautions 5
- Precautions against residual risks 5
- Safety 5
- English 6
- Precautions during maintenance operations 6
- Safety 6
- Aus outlet 7
- Ein inlet 7
- Entrée entrata 7
- Safety 7
- Safety labels 7
- Sortie uscita 7
- English 8
- Safety 8
- Safety regulations 8
- Safety 9
- English 10
- Safety 10
- Anchoring 11
- Inspection 11
- Storage 11
- Transport lifting and positioning 11
- Unit handling 11
- English 12
- Installation 12
- Installation advices 12
- Fixing dimensions 13
- Installation 13
- Maintenance access 13
- English 14
- Installation 14
- Safety differential pressure switch 14
- Water connections 14
- Water piping 14
- Draining the defrosting waste water for heat pump unit only 15
- Hydraulic connection 15
- If the terminal unit is on a lower level than the mql mqh water chiller make sure the water pressure in the chiller is at least 0 bar 15
- Installation 15
- Page 14 15
- Pressure drop in tubes and accessories 15
- Principle diagram of water circuit 15
- Tabella n 2 15
- Table n 1 15
- The grey area shows pressure drop in mm of water gauge m and the velocity in m s recommended for various flows and diameters intermediate values are determined through interpo lation values outside the grey area correspond to exces sive pressure drops and should be avoided table n 2 shows the equivalent length pipe with the same diameter of a few common accessories for this type of installation 15
- The heat pump units must be installed in positions where the defrosting water cannot create any dam age 15
- The mql mqh are to be connected with the termi nal units such as fan coil units cassettes or wall mounted units each terminal unit connected with the mql mqh water chiller and provided with its own control is therefore completely independent of the chiller see diagram of principle on the left 15
- The water inlet outlet fittings shall conform to the in structions provided by the plates affixed neat the connection points 15
- To determine the appropriated pipe section see table n 1 which shows the values of pressure drop for various water flows and the diameter of stan dard copper pipes for hydraulic installations 15
- When heat pump units work in heating mode dur ing defrosting cycles they may discharge water from the base 15
- Electrical connections 16
- English 16
- Installation 16
- Power supply 16
- Preliminary check 17
- Start up 17
- Checking the operation 18
- Delivery to the customer 18
- English 18
- Start up 18
- Before start up 19
- Control system 19
- Minichiller control 19
- Operating instructions 19
- Starting and using the unit 19
- Alarms table 20
- An anomalous noise in the compressor 20
- Control system 20
- English 20
- Failure diagnostics 20
- If the unit is powered by 3 phase current it is essential that the compressor turns in the correct direction the direction of rotation of scroll compressors is fixed the direction of rotation is wrong when while the unit is working you can feel 20
- If you exchange the connections of two out of three phases the compressor inverts the direc tion of rotation and these phenomena disappear suddenly 20
- In case of summer winter switching through re mote contact the unit will operate in cool ing mode when this contact is closed and in heating mode when it is open 20
- Meaning possible cause corrective action 20
- The lack of the correct differential between dis charge pressure and suction pressure i e if the discharge pressure is just above the suc tion pressure 20
- General description 21
- General specifications 21
- Introduction 21
- Air exchanger 22
- Compressors 22
- Coolant circuit 22
- English 22
- General description 22
- Water exchanger 22
- General description 23
- Outline refrigerator mqh hp 4 8 23
- Outline refrigerator mql 10 17 23
- Page 22 23
- English 24
- General description 24
- Outline refrigerator mqh 10 17 24
- Page 23 24
- Page 24 25
- Technical data 25
- English 26
- Page 25 26
- Technical data 26
- Page 26 27
- Technical data 27
- English 28
- Page 27 28
- Technical data 28
- Electrical data compressors 29
- Page 28 29
- Technical data 29
- Unit electrical data 29
- English 30
- Fans electrical data 30
- Page 29 30
- Technical data 30
- Mql mqh 10 17 31
- Mql mqh 4 8 31
- Overall dimensions 31
- Page 30 31
- Technical data 31
- Clearences 32
- English 32
- Technical data 32
- General requirements 33
- Maintenance 33
- Planned maintenance 33
- Compressor 34
- Condenser 34
- Dehydrating filter 34
- English 34
- Maintenance 34
- Refrigerant charge 34
- Evaporator 35
- Maintenance 35
- Thermostatic expansion valve only mql mqh 4 8 35
- English 36
- Troubleshooting 36
- Troubleshooting 37
- English 38
- Oil for compressors 38
- Spare part list 38
- Spare parts 38
- Wiring diagrams 38
- Dismantling demolition and scrapping 39
- Generalities 39
Похожие устройства
- Airwell MQL 15 Техническое описание
- Airwell MQL 15 Инструкция по монтажу
- Airwell MQL17 Инструкция по эксплуатации
- Airwell MQL17 Техническое описание
- Airwell MQL17 Инструкция по монтажу
- Airwell MQH 4 Инструкция по эксплуатации
- Airwell MQH 4 Техническое описание
- Airwell MQH 4 Инструкция по монтажу
- Airwell MQH 6 Инструкция по эксплуатации
- Airwell MQH 6 Техническое описание
- Airwell MQH 6 Инструкция по монтажу
- Airwell MQH 8M Инструкция по эксплуатации
- Airwell MQH 8M Техническое описание
- Airwell MQH 8M Инструкция по монтажу
- Airwell MQH 8Т Инструкция по эксплуатации
- Airwell MQH 8Т Техническое описание
- Airwell MQH 8Т Инструкция по монтажу
- Airwell MQH 10M Инструкция по эксплуатации
- Airwell MQH 10M Техническое описание
- Airwell MQH 10M Инструкция по монтажу