![Fluke 700G [10/34] Hazard location information approvals](/img/pdf.png)
Fluke 700G [10/34] Hazard location information approvals
![Fluke 700G [10/34] Hazard location information approvals](/views2/1436161/page10/bga.png)
700G Series
Calibration Manual
2
Safety Information
A Warning identifies conditions and procedures that are dangerous to the user. A
Caution identifies conditions and procedures that can cause damage to the Product or
the equipment under test.
Warning
To prevent possible electrical shock, fire, or personal injury:
• Only assemble and operate high-pressure systems if you
know the correct safety procedures. High-pressure liquids
and gases are hazardous and the energy from them can be
released without warning.
• Use the Product only as specified, or the protection supplied by
the Product can be compromised.
• The battery door must be closed and locked before you operate
the Product.
• Replace the batteries when the low battery indicator () shows to
prevent incorrect measurements.
• Do not use the Product if it is damaged.
• Disable the Product if it is damaged.
• Read all safety information before you use the Product.
Caution
To prevent possible damage to Product or to equipment under
test:
• If the display reads “OL” the range limit is exceeded and the
pressure source must immediately be removed.
• Do not exceed the maximum torque allowed. Maximum torque
allowed is 13,5 Nm = 10 ft lb.
Hazard Location Information/Approvals
Ex-Hazardous Areas
An Ex-hazardous area as used in this manual refers to an area made hazardous by the
potential presence of flammable or explosive vapors. These areas are also referred to as
hazardous locations, see NFPA 70 Article 500.
® LR110460
Class I, Div. 2, Groups A-D
II 3 G Ex nA IIB T6
KEMA 06ATEX0014 X
Ta=–10 °C... +55 °C
Содержание
- G series 1
- G series calibration manual 1
- Warranty 2
- Table of contents 3
- List of tables 5
- List of figures 7
- How to contact fluke 9
- Introduction 9
- Hazard location information approvals 10
- Safety information 10
- Warning 10
- If the product is exposed to overpressure or sudden physical shock such as being dropped examine it for any damage that can cause a safety concern if necessary return the product for evaluation to fluke refer to the how to contact fluke section 11
- Misuse 11
- Pressure gauge 11
- Special conditions for safe use 11
- Symbols 11
- Symbols used on the product and in this manual are explained in table 1 11
- To prevent possible fire or personal injury the product is intended for installation only in locations providing adequate protection against the entry of solid foreign objects or water capable of impairing safety 11
- Warning 11
- Accuracy 700g ranges 12
- Accuracy 700rg ranges 12
- Available input ranges 12
- Environmental 12
- Media compatibility 12
- Specifications 12
- Mechanical specifications 13
- Calibration manual 14
- G series 14
- Ranges and resolution 14
- Caution for safe operation and maintenance of the product repair the product before use if the battery leaks remove batteries to prevent battery leakage and damage to the product if it is not used for an extended period be sure that the battery polarity is correct to prevent battery leakage have an approved technician repair the product 15
- Caution to prevent possible damage to the product do not use solvents or abrasive cleansers 15
- Clean the product with a soft cloth dampened with water or water and weak soap 15
- How to clean the product 15
- Maintenance 15
- Pressure gauge 15
- How to change the batteries 16
- Warning 16
- How to verify pressure 17
- Performance verification tests 17
- Required equipment 17
- G series 18
- Pressure gauge 19
- G series 20
- Pressure gauge 21
- G series 22
- Pressure gauge 23
- Calibration adjustment 24
- Connections 24
- Enter 2 point adjust mode 24
- Test equipment 24
- Full adjust 25
- Procedure example 25
- Pressure gauge 27
- Bits per second 9600 28
- Data bits 8 28
- Flow control none 28
- G series 28
- Local echo on 28
- Parity none 28
- Serial interface 28
- Stop bits 1 28
- Use terminal communication software on a pc to set up terminal communication an rs 232 to usb cable is necessary this cable comes with 700g track software use these terminal parameters 28
- List of commands 29
- Pressure gauge 29
- Table 5 shows the commands that the product uses to communicate send these commands from the pc to set up the product or to take a measurement 29
- G series 30
- Parameter units 30
- The product can be set to show the measurement units in table 6 30
- A list of error codes are in table 7 31
- Error codes 31
- Pressure gauge 31
- G series 32
- Replacement parts and accessories 32
- Table 8 lists the customer replaceable parts replacement parts can be ordered from fluke corporation and its approved representatives use the part number when you order the replacement part or accessory see the how to contact fluke section 32
- Pressure gauge 33
Похожие устройства
- Fluke 700G Приложение к Руководству по эксплуатации
- Fluke 700G Premium Pressure Accessory Kit _ Краткий справочник
- Fluke 700G Руководство по эксплуатации
- Fluke 700G TRACK _ Руководство по эксплуатации
- Fluke 750P00 Положение об энергозависимости памяти
- Fluke 750P00 Приложение к Инструкции
- Fluke 750P00 Инструкция
- Fluke 750P01 Положение об энергозависимости памяти
- Fluke 750P01 Приложение к Инструкции
- Fluke 750P01 Инструкция
- Fluke 750P02 Положение об энергозависимости памяти
- Fluke 750P02 Приложение к Инструкции
- Fluke 750P02 Инструкция
- Fluke 750P03 Положение об энергозависимости памяти
- Fluke 750P03 Приложение к Инструкции
- Fluke 750P03 Инструкция
- Fluke 750P04 Положение об энергозависимости памяти
- Fluke 750P04 Приложение к Инструкции
- Fluke 750P04 Инструкция
- Fluke 750P22 Положение об энергозависимости памяти