Vitek VT-1211 [6/10] Чистка

Vitek VT-1211 [6/10] Чистка
ВЕРТИКАЛЬНОЕ ОТПАРИВАНИЕ
F Повесьте одежду на плечики.
F Держите утюг вертикально на расстоянии 15F30 см от одежды.
Нажмите на кнопку подачи струи пара (3) несколько раз,
двигая утюгом вдоль того места, которое вы отпариваете.
F При отпаривании глубоких складок нажмите на кнопку
несколько раз.
СИСТЕМА ЗАЩИТЫ ОТ НАКИПИ
Специальный фильтр, расположенный внутри резервуара, уменьшает
жесткость воды и сдерживает отложение извести на подошве утюга.
Фильтр постоянный и не нуждается в замене.
СИСТЕМА “КАПЛЯСТОП”
Гарантирует защиту от протекания подошвы при глажении на низких
температурах: при понижении температуры специальный клапан
перекрывает канал подачи воды из резервуара в камеру
парообразования. Это позволяет гладить наиболее деликатные ткани
без риска испортить их или оставить пятна на одежде.
ЧИСТКА
Перед чисткой отключите утюг от сети и дайте ему остыть. Протрите
поверхность утюга влажной тканью, используя жидкое чистящее
средство (не используйте абразивные вещества). Избегайте резких
соприкосновений с металлическими предметами.
СПЕЦИФИКАЦИЯ
Питание 230 В ~ 50 Гц
Максимальная мощность 1600 Вт
СРОК СЛУЖБЫ УТЮГА НЕ МЕНЕЕ 3Х ЛЕТ
РУССКИЙ
15
F Open the lid 2.
F Raise the tip of the iron to help the water enter the opening without overF
flowing.
F Slowly pour the water into the reservoir using the special measure 13
and taking care not to go over the maximum level (about 270 ml) indicatF
ed by "MAX" on the reservoir.
F Close the lid 0.
Selecting the temperature.
F Put the iron in a vertical position.
F Put the plug in the socket.
F Adjust the thermostat 0 according to the international symbol on the
garment label. The plate temperature control light 0 indicates that the
iron is heating up. Wait until the plate temperature control light goes off
before ironing.
Warning: during ironing, the plate temperature control light 6 comes on
at intervals, indicating that the selected temperature is maintained. If you
lower the thermostat temperature after ironing at a high temperature, do
not start ironing until the plate temperature control light comes on again.
Selecting the steam.
The quantity of steam is regulated by the steam selector 0. Move the
steam selector to a position between minimum and maximum depending
on the quantity of steam required and the temperature selected.
Warning: the Iron gives off steam continuously only if you hold the iron
horizontally. You can stop the continuous steam by placing the iron in a
vertical position or by moving the steam selector to "O". As indicated on
the thermostat knob 0 and in the initial table, you can only use steam at
the highest temperatures. If the selected temperature is too low, water
may drip onto the plate.
Selecting Supersteam and steam when ironing vertically.
Press the superFsteam button 0 to generate a powerful burst of steam
that can penetrate the fabrics and smooth the most difficult and tough
ENGLISH
6
1211.qxd 03.07.03 16:50 Page 12

Содержание

Скачать