Timberk AC TIM 09H PG3 [5/10] Русский

Содержание

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIH llllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllll llllllllllllllll РУССКИЙ 2 In the cooling mode one hour after the sleep mode is set the temperature automatically increases by 1 C In two hours the temperature will increase by 2 C and the established mode is maintained for the rest of the time In the heating mode when SLEEP function is activated the temperature is on the contrary decreased by 2 C in 2 hours 3 When power supply is turned off the sleep mode is automatically switched off 4 When the unit is turned off settings of the sleep mode are automatically turned off The portable air conditioner is equipped with a protective circuit featuring a 3 minute compressor activation delay It means that it takes 3 5 minutes for the compressor to activate after the unit is switched on or dehumidification mode is switched to any other mode 9 Signaling E4 signal is shown on the display at the maximum water level To resume operation remove the rubber plug of the drainage hose at the device s base to drain water at first After water is drained start the unit It will go to the normal operating mode Remote control only for AC TIM 9H P3 AC TIM 12H P3 AC TIM 12H P3 tlmberk 1 FUNC mode selection button SET You can select three functions with this button cooling heating and dehumidification 2 Room temperature setting button TEMP The set temperature is raised by 1 C after a single press on up button and is lowered by 1 C after a single press on down button 16 www timberk ru household air conditioner 3 POWER button pressing this button you can switch on or off the unit 4 SLEEP button after pressing this button the fan sets to low speed 1 Press SLEEP button set the sleep mode Press the button again to cancel the sleep mode 2 In the cooling mode one hour after the sleep mode is set the temperature automatically increases by 1 C In two hours the temperature will increase by 2 C and the established mode is maintained for the rest of the time In the heating mode when SLEEP function is activated the temperature is on the contrary decreased by2 Cin 2 hours 3 When power supply is turned off the sleep mode is automatically switched off 4 When the unit is turned off settings of the sleep mode are automatically turned off 5 Timer button ONTIMER The ON timer is used to automatically switch on the unit upon expiration of the settime 1 Press TIMER button when the unit is OFF to set the desired time 2 After the set time expires the unit will be automatically switched on 3 Press ON OFF button before the set time expires Time setting will be canceled and the unit will be switched on OFF TIMER The OFF timer is used to automatically switch off the unit upon expiration of the set time 1 Press TIMER button when the unit is ON to set the desired time 2 After the set time expires the unit will be automatically switched off 3 Press ON OFF button before the set time expires Time setting will be canceled and the unit will be switched off 6 Automatic fan speed button automatic ventilation mode 7 High speed button Highfan speed 8 Medium speed button Medium fan speed 9 Low speed button Lowfan speed Установка шланга для выброса воздуха рис 5 1 Перед эксплуатацией прибора снимите съемную крышку и достаньте шланг для выброса воздуха после чего установите его в отверстие 2 Поверните шланг вывода воздуха в направлении указанном стрелкой 1 и выньте его из съемной решетки 3 Поверните шланг вывода воздуха в направлении указанном стрелкой 2 и присоедините его к съемной решетке Установка шланга в режимах охлаждение обогрев рис 6 Для включения кондиционера на обогрев необходимо установить шланг на сторону из которой выходит холодный воздух Для включения кондиционера на охлаждение необходимо установить шланг на сторону из которой выходиттеплый воздух Для перевода устройства в необходимый режим охлаждение обогрев Отсоедините съёмную решетку и шланг вывода воздуха как показано стрелкой на Рис 6 А после чего поменяйте их местами В и присоедините к устройству Окончательная конструкция изображена на Рис 6 С Рис 6 5 У ПРАВЛЕНИЕ МОБИЛЬНЫМ КОНДИЦИОНЕРОМ Панель управления для моделей ACTIM 5Н РЗ ACTIM 7Н РЗ рис 7 1 Переключатель режимов работы Влево вправо Выключение центральное положение ручки COOL HEAT режим работы на охлаждение обогрев низкая скорость COOL HEAT i режим работы на охлаждение обогрев высокая скорость FAN SPEED режим работы на вентиляции низкая скорость FAN SPEED режим работы на вентиляции высокая скорость 2 FULL Индикатор заполненности бака конденсатом Если загорается данный индикатор значит емкость для сбора конденсата полна Необходимо выключить прибор и слить конденсат открутив заглушку на трубке 11 рис 4 после чего его опять можно включить 3 POWER индикатор работы кондиционера www timberk ru бытовой кондиционер 5

Скачать