Home
Главная
First
Машинка Для Стрижки Волос
5674-2
Инструкция по эксплуатации Страница: 2

First 5674-2 [2/4] English

HAIR CLIPPER

1. Lower blade

2. Upper blade

3. Blade moving lever

4. Power switch (0/I)

ACCESSORIES

1. Attachment 3mm

2. Attachment 6mm

3. Attachment 9 mm

4. Attachment 12mm

5. Comb

6. Hair scissors

7. Lubricating oil

8. Brush

IMPORTANT SAFETY MEASURES

• Read the instructions carefully before

using the hair clipper.

• Before switching on the unit, make sure

that voltage in your mains corresponds to

the voltage indicated on the unit.

• The unit is not intended for usage by

children or disabled persons.

• Never leave the operating unit unattended.

• Do not allow the children to use the unit as

a toy.

• Keep the unit out of reach of children.

• Use the unit only for the intended

purposes.

• Use only the attachment s and

accessories, supplied with the unit.

• Do not use the unit in places with high

humidity, while taking a bath or a shower.

Do not keep the unit near a bath or a sink,

lled with water. Do not immerse the unit

into water or other liquids; do not wash the

unit under tapping water.

• Do not touch the unit with wet hands.

• Do not try to take the unit if it fell into

water, immediately take the plug out of the

socket. Do not touch water.

• Do not use the hair clipper if the power

plug or the cord is damaged. Apply to the

authorized service center for replacement

of the power cord.

• Do not use the unit in places with high

temperature. Do not place the power cord

near hot surfaces.

• Switch off the unit and take the plug out

of the socket before replacement of the

attachments, cleaning the unit, storing the

unit.

• Never wind the power cord over the body

of the unit.

• Before using the unit make sure that the

blades are set properly, if there is a slant,

align them (refer to Aligning the blades

section).

• Always unplug the unit before placing it.

• Never use the unit if the comb attachment

is broken or damaged or if the blades are

damaged.

• If there are any damages in the unit apply

to the authorized service center.

• The unit is intended for household usage.

The unit is not intended for using on

animals.

ALIGNING THE BLADES

If the blades were removed for cleaning,

replacement, they need to be aligned.

Align the blades on the at and tighten the

fastening screws. The lower blade should

be projected forward, 1- 2 mm relatively the

upper blade. If you could not align the blades,

add several drops of oil (supplied) on the

blades, switch on the unit for several minutes

(30- 40 secк.), then switch off the unit and

take the plug out of the socket. Slightly loose

the fastening screws of the lower blade and

align the blades. After aligning the blades do

not forget to tighten the fastening screws of

the lower blades.

LUBRICATING OIL

To maintain the unit in a good condition, you

should lubricate the blades each time after

haircut. Do not use plant oil or oil, which

includes kerosene or other solvents. Solvents

are subjected to evaporation, and the

remaining thick oil can slow down the speed

of the blades.

In time solvents evaporate and thick oil

remains and will slow down the movement of

the blades.

For lubricating the blades use only the oil,

supplied with the unit.

BLADES MOVING LEVER

The blade moving lever is conveniently

located under the thumb (if you are a right-

hander). During cutting hair you can move

the blade, pressing the lever, adjusting

the length of the hair without usage of the

combs attachments. In the upper position of

the lever, haircut will be the shortest. In the

down position of the lever, the length of the

cut hair is the same as when using the comb

attachment 1 (3 mm). Changing the position

of the lever while cutting hair, you can select

the necessary length of the hair to cut.

If hair is pressed between the blades while

cutting hair, to release them you should move

the lever from the upper position to the down

position several times, it will help to release

the pressed hair, not removing the blades.

When the unit is switched on, move the lever

several times from the “short haircut” position

to the “long haircut” position, this way you can

remove cut-off hair from the blades.

If during cutting the unit pulls hair, it means

that the blades became dull, replace them

with new ones.

INSTRUCTION ON MODELING A HAIRCUT

Before cutting switch on the unit and make

sure that it operates without malfunction, the

blades run smoothly; if there is much oil on

the blades, remove it with a dry cloth.

During operation of the unit, constantly check

the power cord, do not allow its multiple over

twisting, regularly switch off the unit and

straighten the power cord.

The head of the person whose hair you are

cutting should be at the level of your eyes.

Cover the shoulders with a towel, comb the

hair.

Reminder

Cut one-pass small amount of hair, if

necessary return to the cut for additional

haircut.

The best results are achieved while operating

with dry, not wet hair.

START CUTTING

For the rst time it is better to leave longer

hair. With mastering the clipper you can

model different haircuts yourself.

COMB ATTACHMENTS

The length of hair depends on the attachment

used:

Comb attachment 1 hair length 3mm

Comb attachment 2 hair length 6mm

Comb attachment 3 hair length 9 mm

Comb attachment 4 hair length 12mm

To set the comb attachment, asset the upper

part of the attachment on the blade and

press it until the clamp is clipped. To remove

the comb, press the clamp and remove the

attachment.

To achieve even haircut move the clipper

along hair, do not move sharply, cut one-pass

small amount of hair, if necessary return to

the cut for additional haircut.

Remove cut hair from the blades of the unit.

Comb hair to nd out uneven strands.

Step 1

Set the comb attachment 1 (3 mm) or 2 (6

mm). Hold the unit in a way that the blades

are directed upwards. Hold the clipper with

its blades up. Start cutting in direction of hair

growth (Pic. 1). Slowly move the clipper up.

Cut hair from below back of the head and

near ears.

Step 2

Switch off the unit, set the attachment for

long hair 3 (9mm) or 4 (12 mm) and continue

cutting hair near the crown of the head

(pic.2).

Step 3 Cutting in the temple area

Switch off the unit, set the comb 1 (3 mm)

or 2 (6 mm) and cut hair in the temple area.

Then set the comb 3 (9 mm) or 4 (12 mm)

and continue cutting in the direction to the

crown of the head.

Step 4 Cutting in the frontal crown area

Using the comb 3 (9 mm) or 4 (12 mm), cut

hair from the crown towards the top against

the direction of hair growth (pic. 4). You can

cut hair against hair growth and along hair

growth, but bear it in mind that hair that is cut

against hair growth will be shorter than that

that is cut along hair growth.

Using the combs 1 (3 mm) and 2 (6 mm) for

very short haircut. To leave longer hair, use

the necessary comb 3 (9 mm) or 4 (12 mm).

To leave longer hair squeeze hair strands

ENGLISH

First 5674-2 [2/4] English

Содержание

Похожие устройства