![Gigabyte GA-790XT-USB3 (rev.1) [49/112] Onboard lan boot rom](/img/pdf.png)
Gigabyte GA-790XT-USB3 (rev.1) [49/112] Onboard lan boot rom
![Gigabyte GA-790XT-USB3 (rev.1) [49/112] Onboard lan boot rom](/views2/1045466/page49/bg31.png)
- 49 - BIOS Setup
AHCI Congures the SATA controller to AHCI mode. Advanced Host Controller Interface
(AHCI) is an interface specication that allows the storage driver to enable advanced
Serial ATA features such as Native Command Queuing and hot plug. (Default)
RAID Enables RAID for the SATA controller.
Onboard LAN Function
Enables or disables the onboard LAN function. (Default: Enabled)
If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to
Disabled.
Onboard LAN Boot ROM
Allows you to decide whether to activate the boot ROM integrated with the onboard LAN chip.
(Default: Disabled)
This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LAN
cable. This feature will detect cabling issue and report the approximate distance to the fault or short. Refer to
the following information for diagnosing your LAN cable:
When No LAN Cable Is Attached...
If no LAN cable is attached to the motherboard, the Status elds of all four pairs of wires will show Open
and the Length elds show 0m, as shown in the gure above.
When LAN Cable Is Functioning Normally...
If no cable problem is detected on the LAN cable connected to a Gigabit hub or a 10/100 Mbps hub, the
following message will appear:
Start detecting at Port.....
Link Detected --> 100Mbps
Cable Length= 30m
SMART LAN (LAN Cable Diagnostic Function)
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
SMART LAN
Start detecting at Port.....
Part1-2 Status = Open / Length = 0m
Part3-6 Status = Open / Length = 0m
Part4-5 Status = Open / Length = 0m
Part7-8 Status = Open / Length = 0m
higf
: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Item Help
Menu Level
Link Detected Displays transmission speed.
Cable Length Displays the approximate length of the attached LAN cable.
Note: The Gigabit hub will only operate at a speed of 10/100 Mbps in MS-DOS mode; it will operate at a
normal speed of 10/100/1000 Mbps in Windows mode or when the LAN Boot ROM is activated.
Содержание
- Ga 790xt usb3 1
- User s manual 1
- 2009 giga byte technology co ltd all rights reserved the trademarks mentioned in this manual are legally registered to their respective owners 3
- Copyright 3
- Disclaimer 3
- Documentation classifications 3
- Example 3
- For product related information check on our website at http www gigabyte com tw 3
- Identifying your motherboard revision 3
- In order to assist in the use of this product gigabyte provides the following types of documentations 3
- Information in this manual is protected by copyright laws and is the property of gigabyte changes to the specifications and features in this manual may be made by gigabyte with out prior notice no part of this manual may be reproduced copied translated transmitted or published in any form or by any means without gigabyte s prior written permission 3
- The revision number on your motherboard looks like this rev x x for example rev 1 means the revision of the motherboard is 1 check your motherboard revision before updating motherboard bios drivers or when looking for technical information 3
- Box contents optional items ga 790xt usb3 motherboard layout block diagram 4
- Chapter 1 hardware installation 4
- Chapter 2 bios setup 3 4
- Table of contents 4
- Chapter 3 drivers installation 9 5
- Chapter 4 unique features 3 5
- Chapter 5 appendix 5 5
- Box contents 6
- Optional items 6
- Ga 790xt usb3 7
- Ga 790xt usb3 motherboard layout 7
- Block diagram 8
- 1 installation precautions 9
- Chapter 1 hardware installation 9
- 2 product specifications 10
- 3 1 installing the cpu 13
- 3 installing the cpu and cpu cooler 13
- 3 2 installing the cpu cooler 15
- 4 1 dual channel memory configuration 16
- 4 installing the memory 16
- 4 2 installing a memory 17
- 5 installing an expansion card 18
- 6 setup of the ati crossfire 19
- 6 setup of the ati crossfirex configuration 19
- A system requirements 19
- B connecting the graphics cards 19
- C configuring the graphics card driver 19
- Configuration 19
- 7 back panel connectors 20
- Coaxial s pdif out connector 20
- Esata 3gb s port 20
- Ieee 1394a port 20
- Optical s pdif out connector 20
- Ps 2 keyboard and ps 2 mouse port 20
- Rj 45 lan port 20
- Usb 2 1 port 20
- Usb 3 2 port 20
- Center subwoofer speaker out jack orange 21
- Line in jack blue 21
- Line out jack green 21
- Mic in jack pink 21
- Rear speaker out jack black 21
- Side speaker out jack gray 21
- 8 internal connectors 22
- 2 atx_12v_2x4 atx 2x4 12v power connector and 2x12 main power connector 23
- 23 hardware installation 23
- Connectors when using a power supply providing a 2x4 12v and a 2x12 power connector remove the protective covers from the 12v power connector and the main power connector on the motherboard do not insert the power supply cables into pins under the protective covers when using a power supply providing a 2x2 12v and a 2x10 power connector 23
- High power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system 23
- The power connectors are compatible with power supplies with 2x2 12v and 2x10 power 23
- To meet expansion requirements it is recommended that a power supply that can withstand 23
- With the use of the power connector the power supply can supply enough stable power to all the com ponents on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation the 12v power con nector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start 23
- 4 5 cpu_fan sys_fan1 sys_fan2 pwr_fan fan headers 24
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from over 24
- Fdd floppy disk drive connector 24
- Hardware installation 24 24
- Headers 24
- Heating overheating may result in damage to the cpu or the system may hang 24
- The motherboard has a 4 pin cpu fan header cpu_fan a 3 pin sys_fan2 and a 4 pin sys_ fan1 system fan headers and a 3 pin power fan header pwr_fan most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the motherboard supports cpu fan speed control which requires the use of a cpu fan with fan speed control design for optimum heat dissipation it is recom mended that a system fan be installed inside the chassis 24
- These fan headers are not configuration jumper blocks do not place a jumper cap on the 24
- This connector is used to connect a floppy disk drive the types of floppy disk drives supported are 360 kb 720 kb 1 mb 1 4 mb and 2 8 mb before connecting a floppy disk drive be sure to locate pin 1 of the connector and the floppy disk drive cable the pin 1 of the cable is typically designated by a stripe of different color for purchasing the optional floppy disk drive cable please contact the local dealer 24
- Ide ide connector 25
- Sata2_0 1 2 3 4 5 sata 3gb s connectors controlled by amd sb750 25
- F_panel front panel header 26
- 27 hardware installation 27
- Audio signals will be present on both of the front and back panel audio connections simultane 27
- Cd_in cd in connector 27
- F_audio front panel audio header 27
- Front panel audio module refer to the instructions on how to activate ac 97 functionality via the audio software in chapter 5 configuring 2 4 5 7 channel audio 27
- Instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer 27
- Ously if you want to mute the back panel audio only supported when using an hd front panel audio module refer to chapter 5 configuring 2 4 5 7 channel audio 27
- Some chassis provide a front panel audio module that has separated connectors on each wire 27
- The front panel audio header supports hd audio by default if your chassis provides an ac 97 27
- The front panel audio header supports intel high definition audio hd and ac 97 audio you may connect your chassis front panel audio module to this header make sure the wire assignments of the module con nector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it 27
- You may connect the audio cable that came with your optical drive to the header 27
- Spdif_in s pdif in header 28
- Spdif_out s pdif out header 28
- 29 hardware installation 29
- Cord from the power outlet to prevent damage to the usb bracket 29
- Do not plug the ieee 1394 bracket 2x5 pin cable into the usb header prior to installing the usb bracket be sure to turn off your computer and unplug the power 29
- Do not plug the usb bracket cable into the ieee 1394a header prior to installing the ieee 1394a bracket be sure to turn off your computer and unplug the 29
- F_1394 ieee 1394a header 29
- F_usb1 f_usb2 usb headers 29
- Power cord from the power outlet to prevent damage to the ieee 1394a bracket 29
- The header conforms to ieee 1394a specification the ieee 1394a header can provide one ieee 1394a port via an optional ieee 1394a bracket for purchasing the optional ieee 1394a bracket please con tact the local dealer 29
- The headers conform to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer 29
- Then attach the other end of the cable to the ieee 1394a device ensure that the cable is se curely connected 29
- To connect an ieee 1394a device attach one end of the device cable to your computer and 29
- After clearing the cmos values and before turning on your computer be sure to remove the 30
- After system restart go to bios setup to load factory defaults select load optimized de 30
- Always turn off your computer and unplug the power cord from the power outlet before clear 30
- Clr_cmos clearing cmos jumper 30
- Com serial port header 30
- Faults or manually configure the bios settings refer to chapter 2 bios setup for bios configurations 30
- Hardware installation 30 30
- Ing the cmos values 30
- Jumper cap from the jumper failure to do so may cause damage to the motherboard 30
- The com header can provide one serial port via an optional com port cable for purchasing the op tional com port cable please contact the local dealer 30
- Use this jumper to clear the cmos values e g date information and bios configurations and reset the cmos values to factory defaults to clear the cmos values place a jumper cap on the two pins to temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few seconds 30
- Bat battery 31
- Chapter 2 bios setup 33
- 1 startup screen 34
- A the logo screen default 34
- B the post screen 34
- Bios setup 34 34
- Bios setup q flash 34
- Boot menu 34
- Post screen 34
- Q flash 34
- Sata mode message sata is found running at ide mode 34
- The following screens may appear when the computer boots 34
- Xpress recovery2 34
- 2 the main menu 35
- Bios setup program function keys 35
- Sample bios version f1a 35
- Advanced bios features 36
- Exit without saving 36
- Integrated peripherals 36
- Keys for the main menu only 36
- Load fail safe defaults 36
- Load optimized defaults 36
- Mb intelligent tweaker m i t 36
- Pc health status 36
- Power management setup 36
- Save exit setup 36
- Set supervisor password 36
- Set user password 36
- Standard cmos features 36
- 3 mb intelligent tweaker m i t 37
- 37 bios setup 37
- Dent on your overall system configurations incorrectly doing overclock overvoltage may result in damage to cpu chipset or memory and reduce the useful life of these components this page is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results inadequately altering the settings may result in system s failure to boot if this occurs clear the cmos values and reset the board to default values 37
- System voltage control item to auto to optimize the system voltage settings 37
- When the system voltage optimized item blinks in red it is recommended that you set the 37
- Whether the system will work stably with the overclock overvoltage settings you made is depen 37
- Advanced clock calibration 38
- Cpu core 38
- Cpu core control 38
- Ec firmware selection 38
- Value all cores 38
- Value core 0 value core 1 value core 2 value core 3 38
- Cpu clock ratio 39
- Cpu core 39
- Cpu frequency mhz 39
- Cpu host clock control 39
- Cpu northbridge freq 39
- Ht link frequency 39
- Ht link width 39
- Memory clock 39
- Pcie clock mhz 39
- Set memory clock 39
- Allows you to set memory control mode 40
- Bios setup 40 40
- Cpu host clock control cpu frequency mhz set memory clock memory clock 40
- Dcts mode 40
- Ddr3 timing items 40
- Dram configuration 40
- Ganged ganged sets memory control mode to single dual channel 40
- Manual allows all ddr3 timing items below to be configurable 40
- Options are auto default manual options are auto default manual 40
- The settings under the four items above are synchronous to those under the same items on the mb in telligent tweaker m i t main menu 40
- Unganged unganged sets memory control mode to two single channel default 40
- Addr cmd drive strength 41
- Cas latency 41
- Data drive strength 41
- Dqs drive strength 41
- Memclk drive strength 41
- Minimum ras active time 41
- Precharge time 41
- Procodt ohms 41
- Ras to cas r w delay 41
- Ras to ras delay 41
- Row cycle time 41
- Row precharge time 41
- T 2t command timing 41
- Trfc0 for dimm1 41
- Trfc1 for dimm3 41
- Trfc2 for dimm2 41
- Trfc3 for dimm4 41
- Twtr command delay 41
- Write recovery time 41
- Bank interleaving 42
- Channel interleave 42
- Cke drive strength 42
- Cpu pll voltage control 42
- Cs odt drive strength 42
- Ddr vtt voltage control 42
- Dram voltage control 42
- Nb voltage control 42
- Sb ht voltage control 42
- System voltage control 42
- Cpu nb vid control 43
- Cpu voltage control 43
- Nb pcie pll voltage control 43
- Normal cpu vcore 43
- 4 standard cmos features 44
- Access mode access mode sets the hard drive access mode options are auto default chs lba large 44
- Access mode access mode sets the hard drive access mode options are auto default large 44
- Auto lets the bios automatically detect ide sata devices during the post default 44
- Bios setup 44 44
- Configure your ide sata devices by using one of the two methods below configure your ide sata devices by using one of the two methods below 44
- Date mm dd yy 44
- Extended ide drive extended ide drive 44
- Ide auto detection 44
- Ide channel 0 1 master slave 44
- Ide channel 0 1 master slave ide channel 0 1 master slave 44
- Ide channel 2 3 master slave 44
- Ide hdd auto detection 44
- None if no ide sata devices are used set this item to none so the system will skip 44
- Sets the system date the date format is week read only month date and year select the desired field and use the up arrow or down arrow key to set the date 44
- Sets the system time for example 1 p m is 13 0 0 select the desired field and use the up arrow or down arrow key to set the time 44
- The detection of the device during the post for faster system startup the detection of the device during the post for faster system startup 44
- Time hh mm ss 44
- To autodetect the parameters of the ide sata device on this channel 44
- Drive a 45
- Floppy 3 mode support 45
- Halt on 45
- Memory 45
- 5 advanced bios features 46
- Amd c1e support 46
- Amd k8 cool quiet control 46
- Auto lets the amd cool n quiet driver dynamically adjust the cpu clock and vid to 46
- Bios setup 46 46
- Default disabled default disabled 46
- Disabled disabled disables this function 46
- Enables or disables the c1e cpu power saving function in system halt state when enabled the cpu core frequency and voltage will be reduced during system halt state to decrease power consumption default disabled 46
- First second third boot device 46
- Hard disk boot priority 46
- Password check 46
- Program program 46
- Reduce heat output from your computer and its power consumption default reduce heat output from your computer and its power consumption default 46
- Setup setup a password is only required for entering the bios setup program default 46
- Specifies whether a password is required every time the system boots or only when you enter bios setup after configuring this item set the password s under the set supervisor user password item in the bios main menu 46
- System system a password is required for booting the system and for entering the bios setup 46
- To accept options are floppy ls120 hard disk cdrom zip usb fdd usb zip usb cdrom usb hdd legacy lan disabled 46
- To exit this menu when finished 46
- Virtualization 46
- Virtualization allows a platform to run multiple operating systems and applications in independent parti tions with virtualization one computer system can function as multiple virtual systems 46
- Away mode 47
- Backup bios image to hdd 47
- Full screen logo show 47
- Hdd s m a r t capability 47
- Init display first 47
- 6 integrated peripherals 48
- Ahci ahci configures the sata controllers to ahci mode advanced host controller interface 48
- Ahci is an interface specification that allows the storage driver to enable advanced ahci is an interface specification that allows the storage driver to enable advanced 48
- As sata type the mode depends on the as sata type the mode depends on the onchip sata type settings 48
- Bios setup 48 48
- Configures the operating mode of the integrated sata2_0 sata2_3 controller 48
- Enable native ide mode if you wish to install operating systems that support native enable native ide mode if you wish to install operating systems that support native 48
- Enables or disables raid for the sata controller integrated in the jmicron jmb362 chip or configures the sata controller to ahci mode 48
- Enables or disables the integrated ide controller default enabled 48
- Enables or disables the integrated sata controller default enabled 48
- Enables or disables the sata controller integrated in the jmicron jmb362 chip default enabled 48
- Ide ide disables raid for the sata controller and configures the sata controller to ide 48
- Ide ide disables raid for the sata controller and configures the sata controller to pata 48
- Mode default mode default 48
- Mode mode 48
- Native ide native ide allows the sata controller to operate in native ide mode default 48
- Onboard esata controller jmicron jmb362 chip esata connectors on the back panel 48
- Onboard esata mode jmicron jmb362 chip esata connectors on the back panel 48
- Onchip ide channel 48
- Onchip sata controller 48
- Onchip sata port4 5 type amd sb750 sata2_4 sata2_5 connectors 48
- Onchip sata type amd sb750 sata2_0 sata2_3 connectors 48
- Raid raid enables raid for the sata controller 48
- Serial ata features such as native command queuing and hot plug serial ata features such as native command queuing and hot plug 48
- This option is configurable only when onchip sata type is set to raid or ahci configures the oper ating mode of the integrated sata2_4 sata2_5 connectors 48
- Onboard lan boot rom 49
- Onboard lan function 49
- Smart lan lan cable diagnostic function 49
- Legacy usb storage detect 50
- Onboard 1394 function 50
- Onboard audio function 50
- Onboard serial port 1 50
- Onboard usb 3 controller nec usb 3 controller 50
- Onchip usb controller 50
- Usb ehci controller 50
- Usb keyboard support 50
- Usb mouse support 50
- 51 bios setup 51
- 7 power management setup 51
- Acpi suspend type 51
- Allows the system to be awakened from acpi s3 sleep state by a wake up signal from the installed usb device default enabled 51
- Allows the system to be awakened from an acpi sleep state by a wake up signal from a modem that supports wake up function default disabled 51
- Button is pressed for less than 4 seconds the system will enter suspend mode button is pressed for less than 4 seconds the system will enter suspend mode 51
- Configures the way to turn off the computer in ms dos mode using the power button 51
- Delay 4 sec delay 4 sec press and hold the power button for 4 seconds to turn off the system if the power 51
- In s1 sleep state the system appears suspended and stays in a low power mode in s1 sleep state the system appears suspended and stays in a low power mode 51
- In s3 sleep state the system appears to be off and consumes less power than in in s3 sleep state the system appears to be off and consumes less power than in 51
- Instant off instant off press the power button and then the system will be turned off instantly default 51
- Its working state exactly where it was left off its working state exactly where it was left off 51
- Modem ring resume 51
- Note supported on windows 7 vista operating system only 51
- S1 pos s1 pos enables the system to enter the acpi s1 power on suspend sleep state 51
- S3 str s3 str enables the system to enter the acpi s3 suspend to ram sleep state default 51
- Soft off by power button 51
- Specifies the acpi sleep state when the system enters suspend 51
- The s1 state when signaled by a wake up device or event the system resumes to the s1 state when signaled by a wake up device or event the system resumes to 51
- The system can be resumed at any time the system can be resumed at any time 51
- Usb wake up from s3 51
- Ac back function 52
- Eup support 52
- Hpet suppor 52
- Kb power on password 52
- Pme event wake up 52
- Power on by alarm 52
- Power on by keyboard 52
- Power on by mouse 52
- 53 bios setup 53
- 8 pc health status 53
- Case opened 53
- Displays the detection status of the chassis intrusion detection device attached to the motherboard ci header if the system chassis cover is removed this field will show yes otherwise it will show no to clear the chassis intrusion status record set reset case open status to enabled save the settings to the cmos and then restart your system 53
- Enables or disables the cpu overheating protection function when enabled the cpu core voltage and ratio will be reduced when the cpu is overheated default enabled 53
- Hardware thermal control 53
- Keeps or clears the record of previous chassis intrusion status enabled clears the record of previous chassis intrusion status and the case opened field will show no at next boot default disabled 53
- Reset case open status 53
- Cpu smart fan control 54
- Cpu smart fan mode 54
- Cpu system power fan fail warning 54
- Cpu warning temperature 54
- Current cpu system power fan speed rpm 54
- Current system cpu temperature 54
- Current voltage v vcore ddr3 1 v 3 v 12v 54
- System smart fan control 54
- 10 load optimized defaults 55
- 55 bios setup 55
- 9 load fail safe defaults 55
- Key to load the optimal bios default settings the bios defaults settings help the system to operate in optimum state always load the optimized defaults after updating the bios or after clearing the cmos values 55
- Key to load the safest bios default settings in case system instability occurs you may try to load fail safe defaults which are the safest and most stable bios settings for the motherboard 55
- 11 set supervisor user password 56
- Again the message password disabled will appear indicating the password has been can celled 56
- Bios setup 56 56
- Supervisor password 56
- The bios setup program allows you to specify two separate passwords 56
- User password 56
- When a system password is set and the when a system password is set and the password check item in advanced bios features is set to setup you must enter the supervisor password for entering bios setup and making bios changes 56
- When the when the password check item is set to system you must enter the supervisor password or user password at system startup and when entering bios setup 56
- When the when the password check item is set to system you must enter the supervisor password or user password at system startup to continue system boot in bios setup you must enter the supervisor password if you wish to make changes to bios settings the user password only allows you to view the bios settings but not to make changes 56
- 12 save exit setup 57
- 13 exit without saving 57
- 57 bios setup 57
- To return to the bios setup main menu 57
- 1 installing chipset drivers 59
- Chapter 3 drivers installation 59
- 2 application software 60
- 3 technical manuals 60
- 4 contact 61
- 5 system 61
- 6 download center 62
- 1 xpress recovery2 63
- Before you begin 63
- Chapter 4 unique features 63
- Installation and configuration 63
- System requirements 63
- 2 1 updating the bios with the q flash utility 66
- 2 bios update utilities 66
- A before you begin 66
- 67 unique features 67
- B updating the bios 67
- Do not turn off or restart the system when the system is reading updating the bios do not remove the floppy disk usb flash drive or hard drive when the system is updat 67
- Ing the bios 67
- Key during the post to access q flash 67
- Make sure the bios update file matches your motherboard model 67
- Step 3 when the update process is complete press any key to return to the main menu 67
- The save main bios to drive option allows you to save the current bios file q flash only supports usb flash drive or hard drives using fat32 16 12 file system if the bios update file is saved to a hard drive in raid ahci mode or a hard drive attached to 67
- To begin the bios update the monitor will display the update process 67
- When updating the bios choose the location where the bios file is saved the following procedure as sumes that you save the bios file to a floppy disk 67
- To exit q flash and reboot the system as the system boots you should see the new bios version is present on the post screen 68
- To load bios defaults 68
- To load bios defaults system will re detect all peripheral devices after a bios update so we recommend that you reload bios defaults 68
- To save settings to cmos and exit bios setup the proce dure is complete after the system restarts 68
- Unique features 68 68
- 2 2 updating the bios with the bios utility 69
- A before you begin 69
- B using bios 69
- C after updating the bios 69
- 3 easytune 6 70
- Gigabyte s easytune 6 is a simple and easy to use interface that allows users to fine tune their system settings or do overclock overvoltage in windows environment the user friendly easytune 6 interface also includes tabbed pages for cpu and memory information letting users read their system related information without the need to install additional software 70
- Tab function 70
- Tabs information 70
- The easytune 6 interface 70
- Unique features 70 70
- 4 easy energy saver 71
- Meter mode button information table 71
- The easy energy saver interface a meter mode 71
- B total mode 72
- C stealth mode 72
- Total mode button information table 72
- 5 q share 73
- Directions for using q share 73
- Options descriptions 73
- 6 time repair 74
- Preference screen 74
- System restore 74
- 1 1 configuring the onboard sata controller 75
- 1 configuring sata hard drive s 75
- A installing sata hard drive s in your computer 75
- Before you begin 75
- Chapter 5 appendix 75
- To configure sata hard drive s follow the steps below 75
- Appendix 76 76
- B configuring sata controller mode in bios setup 76
- Figure 1 76
- Make sure to configure the sata controller mode correctly in system bios setup 76
- Step 2 save changes and exit bios setup 76
- The bios setup menus described in this section may differ from the exact settings for your moth erboard the actual bios setup menu options you will see shall depend on the motherboard you have and the bios version 76
- To enter bios setup during the post power on self test ensure onchip sata controller is enabled under integrated peripherals to enable raid for the sata2_0 1 2 3 connectors set onchip sata type to raid to enable raid for the sata2_4 5 connectors set onchip sata type to raid and set onchip sata port4 5 type to as sata type figure 1 76
- C configuring raid set in raid bios 77
- Appendix 78 78
- Figure 4 78
- Figure 5 78
- To enter the define ld menu window figure 4 the define ld selection from the main menu allows users to begin the process of manually defining the drive elements and raid levels for one or multiple disk arrays 78
- To enter the raid configuration menu figure 5 78
- 79 appendix 79
- After the creation is complete the screen will return to define ld menu where you will see the newly 79
- Again if you want to exit the raid bios utility 79
- Created array 79
- Disk array the total drv section will show the number of disks assigned 79
- Figure 6 79
- Figure 7 79
- Figure 8 79
- Keys to save the information the window below will appear 79
- Mum capacity 79
- To change the assignment option to y this action adds the drive to the 79
- To clear the mbr or press other keys to ignore this option then the window below 79
- To set the capacity of the raid array or press other keys to set the array to its maxi 79
- View drive assignments the view drive assignments option in the main menu displays whether the attached hard drives are as signed to a disk array or are unassigned under the assignment column drives are labeled with their as signed disk array or shown as free if unassigned 79
- Will appear 79
- Appendix 80 80
- Delete an array the delete array menu option allows for deletion of disk array assignments 80
- Deleting an existing disk array could result in loss of data record all array information including the array type the disk members and stripe block size in case you wish to undo a deletion 80
- Figure 9 80
- If you are sure to delete the array or other keys to abort 80
- In the main menu to enter the delete ld menu then highlight the array you 80
- The view ld definition menu will appear as shown in figure 9 showing which drives are assigned to 80
- To return to main menu 80
- 1 2 configuring jmicron jmb362 sata controller 81
- 81 appendix 81
- A installing sata hard drive s in your computer 81
- Attach one end of the sata signal cable to the rear of the sata hard drive and the other end to available sata port on the motherboard the jmicron jmb362 sata controller controls the esata ports on the back panel then connect the power connector from your power supply to the hard drive 81
- B configuring sata controller mode in bios setup 81
- Figure 1 81
- Make sure to configure the sata controller mode correctly in system bios setup 81
- Step 2 save changes and exit bios setup 81
- The bios setup menus described in this section may differ from the exact settings for your moth erboard the actual bios setup menu options you will see shall depend on the motherboard you have and the bios version 81
- To enter bios setup during the post power on self test make sure onboard esata controller under the integrated peripherals menu is enabled figure 1 to create raid set onboard esata mode to raid 81
- Appendix 82 82
- C configuring a raid array in raid bios 82
- Enter the raid bios setup utility to configure a raid array skip this step and proceed to the installation of windows operating system for a non raid configuration 82
- Figure 2 82
- Figure 3 82
- To enter the raid setup util ity 82
- To see detailed information about the selected hard drive 82
- 83 appendix 83
- Figure 4 83
- Figure 5 83
- On the create raid disk drive item then the create new raid screen appears figure 4 83
- Select raid mode under the level item use up or down arrow key to select raid 0 stripe raid 1 83
- Steps 1 enter array name under the name item enter an array name with 1 16 letters letters cannot be special 83
- The create new raid block displays all the items that need to be set for creating an array figure 5 83
- To move onto the next step 83
- 6 confirm creation after all of the items above are configured the selection bar automatically jumps to the 84
- Appendix 84 84
- Assign array disks after a raid mode is selected raid bios automatically assigns the two hard drives 84
- Figure 6 84
- Figure 7 84
- Installed as the raid drives 84
- Set block size raid 0 only under the block item use the up or down arrow key to select the stripe 84
- To abort 84
- 85 appendix 85
- A small window dis playing the array information will appear in the center of the screen figure 9 85
- Figure 8 85
- Figure 9 85
- When finished the new raid array will be displayed in the raid disk drive list block figure 8 85
- Appendix 86 86
- Figure 10 86
- Figure 11 86
- Now you may proceed to create the sata raid ahci driver diskette and the installation of the sata raid ahci driver and operating system 86
- Save and exit setup after configuring the raid array select the save and exit setup item in the main 86
- To cancel 86
- 1 3 making a sata raid ahci driver diskette 87
- Required for ahci and raid mode 87
- 1 4 installing the sata raid ahci driver and operating system 89
- A installing windows xp 89
- Appendix 90 90
- Figure 3 90
- To continue the driver installation after the driver installation you can pro ceed with the windows xp installation 90
- B installing windows vista 91
- Appendix 96 96
- For the jmicron jmb362 turn off your computer and replace the failed hard drive with a new one use either the raid setup utility or the gigabyte raid configurer utility in the operating system to perform the rebuild 96
- To start the raid rebuilding process the rebuilding progress is displayed at the bottom of the screen when done the status of the array will display as normal 96
- 2 1 configuring 2 4 5 7 channel audio 98
- 2 configuring audio input and output 98
- A configuring speakers 98
- B configuring sound effect 99
- C activating an ac 97 front panel audio module 99
- D muting the back panel audio for hd audio only 99
- 2 2 configuring s pdif in out 100
- A s pdif in 100
- B s pdif out 101
- 2 3 configuring microphone recording 102
- Enabling stereo mix 103
- 2 4 using the sound recorder 104
- A recording sound 104
- B playing the recorded sound 104
- 105 appendix 105
- 3 1 frequently asked questions 105
- 3 troubleshooting 105
- To read more faqs for your motherboard please go to the support downloads motherboard faq page on gigabyte s website 105
- 3 2 troubleshooting procedure 106
- Appendix 106 106
- If you encounter any troubles during system startup follow the troubleshooting procedure below to solve the problem 106
- 107 appendix 107
- If the procedure above is unable to solve your problem contact the place of purchase or local dealer for help or go to the support downloads technical service zone page to submit your question our customer service staff will reply you as soon as possible 107
- 4 regulatory statements 108
- Our commitment to preserving the environment 108
- Regulatory notices 108
- Restriction of hazardous substances rohs directive statement 108
- Waste electrical electronic equipment weee directive statement 108
- Weee symbol statement 108
- China restriction of hazardous substances table 109
- 111 appendix 111
- Contact us 111
- Appendix 112 112
- Gigabyte global service system 112
- To submit a technical or non technical sales market ing question please link to http ggts gigabyte com tw then select your language to enter the system 112
Похожие устройства
- Samsung RSH1K/J*** Инструкция по эксплуатации
- D-Link DSR-500 Инструкция по эксплуатации
- Sven Stream Light Cherry Инструкция по эксплуатации
- Nikon COOLPIX S2600 Black Инструкция по эксплуатации
- LG DS375 Инструкция по эксплуатации
- D-Link DVG-5402SP Инструкция по эксплуатации
- Gigabyte GA-790FXTA-UD5 (rev.1) Инструкция по эксплуатации
- Nikon COOLPIX S3300 Black Инструкция по эксплуатации
- D-Link DVG-7111S Инструкция по эксплуатации
- Gigabyte GA-785GMT-USB3 (rev1) Инструкция по эксплуатации
- Nikon COOLPIX S8200 Black Инструкция по эксплуатации
- D-Link DGL-4100 Инструкция по эксплуатации
- Vitek VT-1611 Инструкция по эксплуатации
- Sven MS-80 Black Инструкция по эксплуатации
- Gigabyte GA-770TA-UD3 (rev.1) Инструкция по эксплуатации
- Nikon COOLPIX P510 Black Инструкция по эксплуатации
- Bosch WLF20180OE Инструкция по эксплуатации
- Gigabyte GA-770T-USB3 (rev.1.3) Инструкция по эксплуатации
- Sven MS-915 дер. 2.1 Инструкция по эксплуатации
- D-Link DFL-1100 Инструкция по эксплуатации
Скачать
Случайные обсуждения