![D-Link DGS-1210-12TS/ME [178/519] Config syslog host](/img/pdf.png)
D-Link DGS-1210-12TS/ME [178/519] Config syslog host
![D-Link DGS-1210-12TS/ME [178/519] Config syslog host](/views2/1459131/page178/bgb2.png)
DGS-1210 Metro Ethernet Managed Switch CLI Reference Guide
160
enable
Command: create syslog host 1 ipaddress 1.1.2.1 severity all state enable
Success.
DGS-1210-28MP/ME:5#
config syslog host
Purpose To configure the syslog protocol to send system log data to a remote
host.
Syntax
config syslog host [all | <index 1-4>] {severity [informational |
warning | all] | facility [local0 | local1 | local2 | local3 | local4 |
local5 | local6 | local7] | state [enable | disable] | udp_port [ 514 |
<udp_port_number 6000-65535>] | ipaddress [<ipaddr> |
<ipv6addr>]}
Description
The config syslog host command configures the syslog protocol to
send system log information to a remote host.
Parameters
all − Specifies that the command applies to all hosts.
<index 1-4> − Specifies that the command applies
to an index of
hosts. There are four available indices, numbered 1 to 4.
severity − The message s
everity level indicator. These are
DGScribed in the following table (
Bold font indicates that the
corresponding severity level is currently supported on the Switch):
Numerical Severity
Code
0 Emergency: system is unusable
1 Alert: action must be taken immediately
2 Critical: critical conditions
3 Error: error conditions
4 Warning: warning conditions
5 Notice: normal but significant condition
6 Informational: informational messages
7 Debug: debug-level messages
informational − Specifies that informational messages are to be sent
to the remote host. This corresponds to number 6 from the list
above.
warning − Specifies that warning messages are to
be sent to the
remote host. This corresponds to number 4 from the list above.
all − Specifies that all message are to be sent to the remote host.
facility − Some of the operating system daemons and processes
have been assigned Facility values. Proces
ses and daemons that
have not been explicitly assigned a Facility may use any of the ‘local
use’ facilities or they may use the ‘user-level’
Facility. Those
Facilities that have been DGSignated are shown in the following:
Bold font indicates the facility v
alues that the Switch currently
supports.
Содержание
- Cli reference guide 1
- Dgs 1210 me series 1
- Table of contents 2
- Introduction 19
- Using the console cli 21
- Command syntax 24
- Square brackets 24
- Vertical bar 24
- Braces 25
- Line editing key usage 25
- Multiple page display control keys 25
- Basic switch commands 26
- Command parameter 26
- Command parameter 27
- Enable password encryption 27
- Create account 28
- Disable password encryption 28
- Config account 29
- Delete account 30
- Reset account 30
- Show account 30
- Show session 31
- Show switch 31
- Show environment 32
- Enable jumbo_frame 33
- Show device_status 33
- Disable jumbo_frame 34
- Show jumbo_frame 34
- Show serial_port 34
- Config serial_port 35
- Config bootrom password 36
- Disable clipaging 36
- Enable clipaging 36
- Disable web 37
- Enable web 37
- Disable autoconfig 38
- Enable autoconfig 38
- Config autoconfig 39
- Show autoconfig 39
- Reboot 40
- Logout 42
- Reload config config_id 42
- Traceroute 45
- Show cpu port 46
- Traceroute6 46
- Reset cpu port 47
- Disable telnet 48
- Enable telnet 48
- Telnet 48
- Config time_range 49
- Show time_range 49
- Show tech support 50
- Clear tech support 52
- Command parameter 53
- Dhcp autoimage commands 53
- Disable autoimage 53
- Enable autoimage 53
- Show autoimage 54
- Command parameter 55
- Disable smtp 55
- Enable smtp 55
- Smtp server commands 55
- Config smtp 56
- Show smtp 56
- Smtp sent_testmsg 57
- Command parameter 59
- Config command_prompt 59
- Modify banner and prompt commands 59
- Config greeting_message 60
- Show greeting_message 61
- Command parameter 62
- Disable ddp 62
- Dlink discover protocol commands 62
- Enable ddp 62
- Config ddp report state 63
- Config ddp report timer 63
- Config ddp ports 64
- Show ddp 64
- Command parameter 66
- Config ports 66
- Switch port commands 66
- Config ports 67
- Show ports 68
- Show ports 69
- Delete ports 70
- Command parameter 71
- Disable loopdetect 71
- Enable loopdetect 71
- Loopback detection commands 71
- Config loopdetect mode 72
- Config loopdetect ports 72
- Config loopdetect 73
- Show loopdetect 73
- Command parameter 75
- Config dos_prevention dos_type 75
- Dos prevention commands 75
- Show dos_prevention 76
- Disable dos_prevention trap_log 77
- Enable dos_prevention trap_log 77
- Command parameter 78
- Config pppoe circuit_id_insertion state 78
- Pppoe circuit id insertion commands 78
- Config pppoe circuit_id_insertion ports 79
- Show pppoe circuit_id_insertion 79
- Show pppoe circuit_id_insertion ports 80
- Command parameter 81
- Dhcp server screening commands 81
- Command parameter 82
- Config filter dhcp_server 82
- Config filter dhcp_server log 83
- Show filter dhcp_server 83
- Show dhcp_server screening 84
- Config filter dhcpv6_server log 85
- Config filter dhcpv6_server ports 85
- Create filter dhcpv6_server permit_entry 85
- Delete filter dhcpv6_server permit_entry 86
- Show filter dhcpv6_server 86
- Config filter icmpv6_ra_all_node log 87
- Config filter icmpv6_ra_all_node ports 87
- Create filter icmpv6_ra_all_node permit_server 88
- Delete filter icmpv6_ra_all_node permit_server 88
- Show filter icmpv6_ra_all_node 89
- Command parameter 90
- Ip mac port binding commands 90
- Command parameter 91
- Create address_binding ip_mac 91
- Config address_binding ip_mac log 92
- Config address_binding ip_mac ports 92
- Config address_binding auto_scan 93
- Config address_binding auto_scan ipv6address 93
- Show address_binding ip_mac log 93
- Delete address_binding 94
- Show address_binding 95
- Disable address_binding dhcp_snoop 96
- Enable address_binding dhcp_snoop 96
- Show address_binding auto_scan list 96
- Config address_binding dhcp_snoop max_entry ports 97
- Show address_binding dhcp_snoop 97
- Disable address_binding dhcp_pd_snoop 98
- Enable address_binding dhcp_pd_snoop 98
- Config address_binding vlan 99
- Show address_binding dhcp_pd_snoop 99
- Disable address_binding roaming 100
- Enable address_binding roaming 100
- Show address_binding roaming 100
- Clear address_binding dhcp_snoop binding_entry ports 101
- Command parameter 102
- Network management snmp commands 102
- Command parameter 103
- Command parameter 104
- Command parameter 105
- Create snmp user 105
- Delete snmp user 106
- Create snmp view 107
- Show snmp user 107
- Delete snmp view 108
- Show snmp view 108
- Create snmp community 109
- Delete snmp all_community 110
- Delete snmp community 110
- Show snmp community 110
- Config snmp engineid 111
- Show snmp engineid 111
- Disable community_encryption 112
- Enable community_encryption 112
- Create snmp group 113
- Show community_encryption 113
- Delete snmp group 114
- Show snmp global state 115
- Show snmp groups 115
- Create snmp host 116
- Delete snmp host 117
- Show snmp host 117
- Create snmp v6host 118
- Delete snmp v6host 119
- Show snmp v6host 119
- Disable trusted_host 120
- Enable trusted_host 120
- Create trusted_host 121
- Delete trusted_host 122
- Show trusted_host 122
- Disable snmp traps 123
- Enable snmp traps 123
- Disable snmp authenticate_traps 124
- Enable snmp authenticate_traps 124
- Show snmp traps 124
- Disable snmp linkchange_traps 125
- Enable snmp linkchange_traps 125
- Config snmp linkchange_traps ports 126
- Show snmp traps linkchange_traps 126
- Config snmp system_contact 127
- Config snmp system_location 127
- Config snmp system_name 128
- Config snmp warmstart_traps 128
- Config snmp coldstart_traps 129
- Disable snmp 129
- Enable snmp 129
- Disable snmp dhcp_ screening traps 130
- Enable snmp dhcp_ screening traps 130
- Disable snmp dhcpv6_ screening traps 131
- Enable snmp dhcpv6_ screening traps 131
- Enable snmp icmpv6_ra_all_node traps 131
- Disable snmp icmpv6_ra_all_node traps 132
- Disable snmp impb_violation traps 132
- Enable snmp impb_violation traps 132
- Disable snmp firmware_upgrade_state traps 133
- Enable snmp firmware_upgrade_state traps 133
- Disable snmp lbd traps 134
- Enable snmp lbd traps 134
- Enable snmp port_security_violation traps 134
- Disable snmp port_security_violation traps 135
- Enable snmp rstpport_state_change traps 135
- Disable snmp duplicate_ip_detected traps 136
- Disable snmp rstpport_state_change traps 136
- Enable snmp duplicate_ip_detected traps 136
- Command parameter 138
- Download 138
- Download upload commands 138
- Download 139
- Upload 140
- Config configuration config_id 141
- Show firmware information 141
- Show config 142
- Config firmware image_id 143
- Show boot_file 143
- Show flash information 144
- Command parameter 145
- Dhcp relay commands 145
- Command parameter 146
- Disable dhcp_relay 146
- Enable dhcp_relay 146
- Config dhcp_relay add ipif system 147
- Config dhcp_relay port 147
- Config dhcp_relay delete ipif system 148
- Config dhcp_relay hops 148
- Config dhcp_relay option_82 149
- Config dhcp_relay vlan 149
- Config dhcp_relay port_option_82 151
- Show dhcp_relay port_option_82 151
- Enable dhcp_local_relay 152
- Show dhcp_relay 152
- Config dhcp_local_relay port 153
- Disable dhcp_local_relay 153
- Config dhcp_local_relay vlan 154
- Show dhcp_local_relay 154
- Disable dhcpv6_relay 155
- Enable dhcpv6_relay 155
- Show dhcpv6_relay 155
- Config dhcpv6_relay 156
- Config dhcpv6_relay hop_count 157
- Config dhcpv6_relay option_18 157
- Config dhcpv6_relay option_37 158
- Config dhcpv6_relay option_38 158
- Show dhcpv6_relay option_38 159
- Command parameter 160
- Config gratuitous_arp send ipif_status_up 160
- Gratuitous arp commands 160
- Config gratuitous_arp learning 161
- Config gratuitous_arp send dup_ip_detected 161
- Disable gratuitous_arp log 162
- Enable gratuitous_arp log 162
- Config gratuitous_arp log 163
- Show gratuitous_arp 163
- Config gratuitous_arp send periodically ipif 164
- Command parameter 165
- Config power_saving 165
- Config power_saving mode 165
- Power saving commands 165
- Show power_saving 166
- Command parameter 167
- Cpu protection commands 167
- Disable cpu_protect 167
- Enable cpu_protect 167
- Config cpu_protect type 168
- Show cpu_protect 168
- Command parameter 170
- Network monitoring commands 170
- Show packet ports 170
- Show error ports 171
- Show utilization 172
- Clear counters 173
- Clear log 173
- Save log 173
- Enable syslog 174
- Show log 174
- Disable syslog 175
- Show syslog 175
- Create syslog host 176
- Config syslog host 178
- Delete syslog host 180
- Show syslog host 180
- Cable diagnostic port 181
- Config syslogintimeout 181
- Config sysgroupinterval 182
- Show log_software_module 182
- Command parameter 184
- Config poe ports 184
- Poe commands 184
- Config poe system 185
- Show poe ports 185
- Show poe system 186
- Command parameter 188
- Config stp 188
- Spanning tree commands 188
- Config stp ports 189
- Config stp fbpdu 191
- Config stp version 191
- Config stp priority 192
- Disable stp 192
- Enable stp 192
- Show stp 193
- Show stp ports 194
- Show stp instance 195
- Create stp instance_id 196
- Show stp mst_config_id 196
- Config stp instance_id 197
- Delete stp instance_id 197
- Config stp mst_config_id 198
- Config stp mst_ports 198
- Config stp trap 199
- Command parameter 201
- Create fdb 201
- Forwarding database commands 201
- Config fdb aging_time 202
- Delete fdb 202
- Config flood_fdb 203
- Disable flood_fdb 203
- Enable flood_fdb 203
- Clear flood_fdb 204
- Show flood_fdb 204
- Show fdb 205
- Clear fdb 206
- Config multicast vlan_filtering_mode 206
- Config multicast_filtering_mode 207
- Delete auto_fdb 207
- Broadcast storm control commands 208
- Command parameter 208
- Config traffic control 208
- Config traffic control auto_recover_time 209
- Show traffic control 209
- Config traffic trap 210
- Command parameter 211
- Disable password_recovery 211
- Enable password_recovery 211
- Password recovery commands 211
- Show password_recovery 212
- Command parameter 213
- Qos commands 213
- Command parameter 214
- Config scheduling 215
- Show scheduling 215
- Config bandwidth_control 216
- Config cos mac_mapping 217
- Show bandwidth_control 217
- Delete cos mac_mapping 218
- Show cos mac_mapping 218
- Config cos ip_mapping 219
- Show cos ip_mapping 219
- Config cos ipv6_mapping 220
- Delete cos ip_mapping 220
- Show cos ipv6_mapping 220
- Config cos ipv6_tc_mapping 221
- Delete cos ipv6_mapping 221
- Delete cos ipv6_tc_mapping 222
- Show cos ipv6_tc_mapping 222
- Config cos mapping 223
- Show cos mapping 223
- Config cos protocol_mapping 224
- Show cos protocol_mapping 224
- Config cos vlanid_mapping 225
- Delete cos protocol_mapping 225
- Show cos vlanid_mapping 225
- Config cos tos value 226
- Delete cos vlanid_mapping 226
- Config cos tcp_port_mapping 227
- Show cos tos 227
- Delete cos tcp_port_mapping 228
- Show cos tcp_port_mapping 228
- Config cos udp_port_mapping 229
- Show cos udp _port_mapping 229
- Config 802 p user_priority 230
- Delete cos udp_port_mapping 230
- Config 802 p default_priority 231
- Show 802 p user_priority 231
- Config scheduling_mechanism 232
- Show 802 p default_priority 232
- Show scheduling_mechanism 233
- Config dscp tos mode 234
- Config dscp_mapping 234
- Enable hol_prevention 235
- Show dscp_mapping 235
- Disable hol_prevention 236
- Show hol_prevention 236
- Command parameter 237
- Config reboot schedule 237
- Reboot schedule commands 237
- Delete reboot schedule 238
- Show reboot schedule 238
- Command parameter 240
- Enable rmon 240
- Rmon commands 240
- Create rmon alarm 241
- Disable rmon 241
- Delete rmon alarm 242
- Show rmon alarm 242
- Create rmon collection stats 243
- Create rmon collection history 244
- Delete rmon collection stats 244
- Create rmon event 245
- Delete rmon collection history 245
- Delete rmon event 246
- Show rmon 246
- Show rmon statistics 246
- Command parameter 248
- Disable mirror 248
- Enable mirror 248
- Port mirroring commands 248
- Config mirror target 249
- Show mirror 250
- Erps commands 251
- Enable erps 252
- Config erps raps_vlan ring_mel 253
- Create erps raps_vlan 253
- Disable erps 253
- Config erps raps_vlan ring_port 254
- Config erps raps_vlan rpl 255
- Config erps raps_vlan protected_vlan 256
- Config erps raps_vlan timer 256
- Config erps raps_vlan state 257
- Config erps raps_vlan sub_ring 258
- Config erps raps_vlan revertive 259
- Config erps raps_vlan tc_propagation 259
- Delete erps raps_vlan 260
- Show erps 260
- Config erps log 261
- Config erps ring ring_id 262
- Config erps trap 262
- Create erps ring 262
- Config erps ring instance 263
- Config erps ring ring_type 263
- Config erps ring ring_port 264
- Config erps instance state 265
- Delete erps ring 265
- Show erps ring 265
- Config erps instance sub_ring_instance 266
- Config erps instance raps_vlan 267
- Config erps instance tc_propagation 267
- Config erps instance mel 268
- Config erps instance protected_vlan 269
- Config erps instance rpl 269
- Config erps instance timer 270
- Config erps instance revertive mode 271
- Erps clear instance 272
- Show erps instance 272
- Erps force switch instance 273
- Erps manual switch instance 273
- Config erps version 274
- Command parameter 275
- Vlan commands 275
- Command parameter 276
- Create vlan 276
- Config vlan 277
- Delete vlan 277
- Config private_vlan 278
- Config private_vlan trunk 279
- Config gvrp 280
- Show private_vlan 280
- Config gvrp timer 281
- Enable gvrp 281
- Disable gvrp 282
- Show vlan 282
- Config dot1v_protocol_group 283
- Create dot1v_protocol_group 283
- Delete dot1v_protocol_group 284
- Show dot1v_protocol_group 284
- Config port dot1v ports 285
- Show gvrp 286
- Show port dot1v 286
- Enable vlan_trunk 287
- Show gvrp timer 287
- Config vlan_trunk ports 288
- Disable vlan_trunk 288
- Show vlan_trunk 288
- Disable asymmetric_vlan 289
- Enable asymmetric_vlan 289
- Disalbe pvid auto_assign 290
- Enable pvid auto_assign 290
- Show asymmetric_vlan 290
- Create mac_based_vlan mac_address 291
- Show pvid auto_assign 291
- Deleete mac_based_vlan mac address 292
- Show mac_based_vlan mac address 292
- Config vlan_auto_learn 293
- Show vlan_auto_learn 293
- Command parameter 295
- Mac based access control commands 295
- Config mac_based_access_control password 296
- Disable mac_based_access_control 296
- Enable mac_based_access_control 296
- Config mac_based_access_control method 297
- Config mac_based_access_control port 297
- Config mac_based_access_control log state 298
- Config mac_based_access_control trap state 298
- Config mac_based_access_control log max_users 299
- Create mac_based_access_control_local mac_address 299
- Show mac_based_access_control 300
- Show mac_based_access_control_local 300
- Delete mac_based_access_control_local 301
- Show mac_based_access_control auth_state ports 301
- Command parameter 303
- Enable qinq 303
- Q in q commands 303
- Disable qinq 304
- Show qinq 304
- Config qinq inner_tpid 305
- Config qinq ports 305
- Create vlan_translation 306
- Show vlan_translation 306
- Delete vlan_translation ports 307
- Command parameter 308
- Create link_aggregation 308
- Link aggregation commands 308
- Config link_aggregation group_id 309
- Delete link_aggregation 309
- Config link_aggregation algorithm 310
- Config link_aggregation state 310
- Show link_aggregation 311
- Basic ip commands 312
- Command parameter 312
- Create ipif 312
- Delete ipif 313
- Disable ipif 313
- Enable ipif 313
- Config ipif 314
- Bpdu attack protection commands 316
- Command parameter 316
- Config bpdu_protection ports 316
- Config bpdu_protection recovery_timer 317
- Config bpdu_protection 318
- Enable bpdu_protection 318
- Disable bpdu_protection 319
- Show bpdu_protection 319
- Command parameter 321
- Create mac_protection 321
- Delete mac_protection 321
- Mac protection commands 321
- Show mac_protection 322
- Command parameter 323
- Config ethernet_oam ports 323
- Ethernet oam commands 323
- Config ethernet_oam ports 324
- Show ethernet_oam ports 325
- Show ethernet_oam ports 326
- Show ethernet_oam ports 327
- Show ethernet_oam ports 328
- Clear ethernet_oam ports 329
- Command parameter 330
- Disable mac_notification 330
- Enable mac_notification 330
- Mac notification commands 330
- Config mac_notification 331
- Config mac_notification ports 331
- Show mac_notification 332
- Show mac_notification ports 332
- Command parameter 334
- Igmp snooping commands 334
- Command parameter 335
- Config igmp_snooping 335
- Config igmp_snooping querier 336
- Config igmp_snooping multicast_vlan 337
- Create igmp_snooping multicast_vlan 337
- Config igmp_snooping multicast_vlan_group 338
- Delete igmp_snooping multicast_vlan 338
- Create igmp_snooping static_group 339
- Config igmp_snooping static_group 340
- Delete igmp_snooping static_group 340
- Config igmp_snooping data_driven_learning 341
- Show igmp_snooping static_group 341
- Config igmp_snooping data_driven_learning 342
- Clear igmp_snooping data_driven_group 343
- Config router_ports 343
- Config router_ports_forbidden 344
- Config igmp access_authentication ports 345
- Show igmp access_authentication ports 345
- Disable igmp_snooping 346
- Enable igmp_snooping 346
- Show igmp_snooping 347
- Show igmp_snooping group 347
- Show igmp_snooping forwarding 348
- Show igmp_snooping host 349
- Show igmp_snooping multicast_vlan 349
- Show igmp_snooping multicast_vlan_group 350
- Show igmp_snooping statistic counter 350
- Clear igmp_snooping statistic counter 351
- Show router_ports 351
- Command parameter 353
- Create iproute 353
- Ipv4 ipv6 routing commands 353
- Delete iproute 354
- Show iproute 354
- Create ipv6route 355
- Delete ipv6route 355
- Show ipv6route 356
- Command parameter 357
- Disable l2protocol_tunnel 357
- Enable l2protocol_tunnel 357
- Layer 2 protocol tunneling commands 357
- Config l2protocol_tunnel ports 358
- Show l2protocol_tunnel 358
- Command parameter 360
- Config ddm ports 360
- Digital diagnostic monitoring commands 360
- Config ddm power_unit 361
- Show ddm ports 361
- Command parameter 363
- Mld snooping commands 363
- Command parameter 364
- Disable mld_snooping 364
- Enable mld_snooping 364
- Config mld_snooping 365
- Config mld_snooping multicast_vlan 366
- Create mld_snooping multicast_vlan 366
- Delete mld_snooping multicast_vlan 367
- Show mld_snooping multicast_vlan 367
- Config mld_snooping multicast_vlan_group 368
- Show mld_snooping multicast_vlan_group 368
- Config mld_snooping mrouter_ports 369
- Config mld_snooping mrouter_ports_forbidden 369
- Config mld_snooping querier 370
- Config mld_snooping data_driven_learning 371
- Clear mld_snooping data_driven_group 372
- Show mld_snooping 372
- Show mld_snooping forwarding 373
- Show mld_snooping group 374
- Show mld_snooping mrouter_ports 374
- Show mld_snooping host 375
- Clear mld_snooping statistics counter 376
- Show mld_snooping statistics counter 376
- Command parameter 377
- Create mcast_filter_profile 377
- Limited ip multicast address commands 377
- Config mcast_filter_profile profile_id 378
- Config mcast_filter_profile profile_name 378
- Config mcast_filter_profile ipv6 379
- Delete mcast_filter_profile 379
- Show mcast_filter_profile 380
- Config limited_multicast_addr 381
- Show limited_multicast_addr 381
- Config max_mcast_group 382
- Show max_mcast_group 382
- Command parameter 384
- X commands 384
- Command parameter 385
- Disable 802 x 385
- Enable 802 x 385
- Show 802 x 386
- Show 802 x auth_state 386
- Show 802 x auth_configuration 387
- Config 802 x auth_parameter ports 388
- Config 802 x init 389
- Config 802 x auth_protocol 390
- Config 802 x reauth 390
- Config radius add 391
- Config radius 392
- Config radius delete 392
- Config 802 x fwd_pdu system 393
- Show radius 393
- Config 802 x auth_mode 394
- Show 802 x fwd_pdu system status 394
- Create 802 x guest_vlan 395
- Delete 802 x guest_vlan 395
- Config 802 x guest_vlan ports 396
- Show 802 x guest_vlan 396
- Create 802 x user 397
- Show 802 x user 397
- Config 802 x capability ports 398
- Delete 802 x user 398
- Command parameter 400
- Config port_security 400
- Port security commands 400
- Show port_security 401
- Clear port_security _entry 402
- Delete port_security _entry 402
- Command parameter 403
- Config sntp 403
- Time and sntp commands 403
- Enable sntp 404
- Show sntp 404
- Config time 405
- Disable sntp 405
- Config dst 406
- Config time_zone operator 406
- Show time 407
- Arp commands 409
- Command parameter 409
- Config arp_aging time 409
- Clear arptable 410
- Create arpentry 410
- Config arpentry 411
- Delete arpentry 411
- Show arpentry 412
- Show arpentry aging_time 412
- Command parameter 413
- Enable rspan 413
- Remote switched port analyzer commands 413
- Create rspan vlan 414
- Disable rspan 414
- Config rspan vlan 415
- Delete rspan vlan 416
- Show rspan 416
- Command parameter 417
- Sflow commands 417
- Disable sflow 418
- Enable sflow 418
- Show sflow 418
- Create sflow flow_sampler ports 419
- Config sflow flow_sampler ports 420
- Delete sflow flow_sampler ports 420
- Show sflow flow_sampler 421
- Create sflow analyzer_server 422
- Config sflow analyzer_server 423
- Delete sflow analyzer_server 423
- Show sflow analyzer_server 424
- Config sflow counter_poller ports 425
- Create sflow counter_poller ports 425
- Delete sflow counter_poller ports 426
- Show sflow counter_poller 426
- Command parameter 428
- Commands 428
- Config duld ports 428
- D link unidirectional link detection duld 428
- D link unidirectional link detection duld commands 428
- Config duld recover_timer 429
- Show duld ports 429
- Show duld recover_timer 430
- Command parameter 431
- Create ipv6 neighbor_cache 431
- Ipv6 neighbor discovery commands 431
- Delete ipv6 neighbor_cache 432
- Show ipv6 neighbor_cache 432
- Config ipv6 nd ns ipif 433
- Show ipv6 nd 433
- Disable ipif_ipv6_link_local_auto 434
- Enable ipif_ipv6_link_local_auto 434
- Banner commands 436
- Command parameter 436
- Config log_save_timing 436
- Show log 437
- Show log_save_timing 437
- Command history list commands 438
- Command parameter 438
- Show command_history 439
- Command logging commands 441
- Command parameter 441
- Disable command logging 441
- Enable command logging 441
- Show command logging 442
- Command parameter 443
- Enable ssh 443
- Ssh commands 443
- Config ssh algorithm 444
- Disable ssh 444
- Config ssh authmode 445
- Show ssh authmode 445
- Config ssh server 446
- Show ssh server 446
- Config ssh user 447
- Show ssh algorithm 447
- Show ssh user authmode 448
- Command parameter 449
- Enable ssl 449
- Ssl commands 449
- Disable ssl 450
- Show ssl 450
- Download ssl certificate 451
- Access authentication control commands 452
- Command parameter 452
- Command parameter 453
- Create authen_login method_list_name 453
- Config authen_login 454
- Delete authen_login method_list_name 455
- Show authen_login 455
- Show authen_policy 456
- Config authen_enable 457
- Create authen_enable method_list_name 457
- Delete authen_enable method_list_name 459
- Show authen_enable 459
- Disable authen_policy 460
- Enable authen_policy 460
- Config authen application 461
- Show authen application 461
- Config authen parameter 462
- Create authen server_host 463
- Show authen parameter 463
- Config authen server_host 464
- Delete authen server_host 465
- Show authen server_host 466
- Config authen server_group 467
- Create authen server_group 467
- Delete authen server_group 468
- Show authen server_group 468
- Enable admin 469
- Config accounting 470
- Config admin local_enable 470
- Config accounting service 471
- Config accounting service command 472
- Create accounting method_list_name 472
- Delete accounting method_list_name 473
- Show accounting method_list_name 473
- Disable aaa_server_password_encryption 474
- Enable aaa_server_password_encryption 474
- Show aaa 475
- Command parameter 476
- Config eee port 476
- Energy efficient ethernet commands 476
- Show eee_mode port 476
- Command parameter 478
- Config lacp port_priority 478
- Lacp commands 478
- Show lacp 478
- Config lacp_ports 479
- Command parameter 481
- Lldp commands 481
- Config lldp message_tx_interval 482
- Disable lldp 482
- Enable lldp 482
- Config lldp message_tx_hold_multiplier 483
- Config lldp reinit_delay 483
- Config lldp notification_interval 484
- Config lldp tx_delay 484
- Show lldp 485
- Show lldp ports 485
- Show lldp local_ports 486
- Config lldp ports 487
- Show lldp remote_ports 487
- Config lldp ports 488
- Config lldp ports 489
- Config lldp ports 490
- Config lldp ports 491
- Show lldp mgt_addr 491
- Show lldp power_pse_tlv 492
- Show lldp statistics 492
- Access control list commands 493
- Command parameter 493
- Command parameter 494
- Create access_profile 494
- Config access_profile 496
- Delete access_profile 500
- Show access_profile 500
- Create cpu_access_profile 501
- Config cpu_access_profile 503
- Delete cpu_access_profile 504
- Enable cpu_interface_filtering 505
- Show cpu_access_profile 505
- Config flow_meter profile_id 506
- Disable cpu_interface_filtering 506
- Show flow_meter 507
- Command parameter 508
- Config traffic_segmentation 508
- Show traffic_segmentation 508
- Traffic segmentation commands 508
- Command parameter 510
- Config safeguard_engine 510
- Safeguard commands 510
- Show safeguard_engine 510
- Device specifications 512
- Technical specifications 512
- Supported transceivers 518
Похожие устройства
- D-Link DGS-1210-12TS/ME Краткое руководство по установке
- D-Link DGS-1210-12TS/ME Руководство пользователя _Web UI_
- D-Link DGS-1210-28X/ME Руководство пользователя
- D-Link DGS-1210-28X/ME Руководство пользователя _CLI_
- D-Link DGS-1210-28X/ME Руководство пользователя _Web UI_
- D-Link DGS-1210-28X/ME Краткое руководство по установке
- D-Link DGS-1210-28XS/ME Руководство пользователя
- D-Link DGS-1210-28XS/ME Краткое руководство по установке
- D-Link DGS-1210-28XS/ME Руководство пользователя _Web UI_
- D-Link DGS-1210-28XS/ME Руководство пользователя _CLI_
- D-Link DGS-1210-52/ME rev.B Руководство пользователя _CLI_
- D-Link DGS-1210-52/ME rev.B Краткое руководство по установке
- D-Link DGS-1210-52/ME rev.B Руководство пользователя _Web UI_
- D-Link DGS-1210-52/ME rev.A Руководство по установке
- D-Link DGS-1210-52/ME rev.A Руководство пользователя _Web UI_
- D-Link DGS-1210-52/ME rev.A Руководство пользователя _CLI_
- D-Link DGS-1210-52MPP/ME Краткое руководство по установке
- D-Link DGS-1210-52P/ME Краткое руководство по установке
- D-Link DGS-1510-10L/ME Руководство пользователя _Web UI_
- D-Link DGS-1510-10L/ME Руководство пользователя _CLI_
Скачать
Случайные обсуждения