![Hikoki G 23MR [3/152] Kickback and related warnings](/img/pdf.png)
Hikoki G 23MR [3/152] Kickback and related warnings
![Hikoki G 23MR [3/152] Kickback and related warnings](/views2/1471518/page3/bg3.png)
3
English
SAFETY WARNINGS COMMON FOR
GRINDING OR ABRASIVE CUTTING-
OFF OPERATIONS
a) This power tool is intended to function as a
grinder or cut-off tool. Read all safety warnings,
instructions, illustrations and specifi cations
provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
b) Operations such as sanding, wire brushing or
polishing are not recommended to be performed
with this power tool.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
c)
Do not use accessories which are not specifi cally
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
d)
The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can
break and fl y apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted
by fl anges, the arbour hole of the accessory must
fi t the locating diameter of the fl ange.
Accessories that do not match the mounting hardware of
the power tool will run out of balance, vibrate excessively
and may cause loss of control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
h)
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping fl ying
debris generated by various operations. The dust mask
or respirator must be capable of fi ltrating particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a broken accessory may
fl y away and cause injury beyond immediate area of
operation.
j) Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord.
Cutting accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and could
give the operator an electric shock.
k) Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning accessory.
l) Never lay the power tool down until the accessory
has come to a complete stop.
The spinning accessory may grab the surface and pull
the power tool out of your control.
m)
Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
o)
Do not operate the power tool near fl ammable materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED
WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the accessory’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing
the wheel to climb out or kick out. The wheel may either jump
toward or away from the operator, depending on direction of
the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a)
Maintain a fi rm grip on the power tool and position your
body and arm to allow you to resist kickback forces.
Always use auxiliary handle, if provided, for maximum
control over kickback or torque reaction during start-up.
The operator can control torque reactions or kickback
forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power
tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to the
wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback and loss of control.
SAFETY WARNINGS SPECIFIC FOR
GRINDING AND ABRASIVE CUTTING-
OFF OPERATIONS
a) Use only wheel types that are recommended for
your power tool and the specifi c guard designed
for the selected wheel.
Wheels for which the power tool was not designed
cannot be adequately guarded and are unsafe.
0000Book_G18MR.indb 30000Book_G18MR.indb 3 2017/11/29 10:57:332017/11/29 10:57:33
Содержание
- G 18mr 1
- G 18mru 1
- G 23mr 1
- G 23mru 1
- English 2
- General power tool safety warnings 2
- English 3
- Kickback and related warnings 3
- Safety warnings common for grinding or abrasive cutting off operations 3
- Safety warnings specific for grinding and abrasive cutting off operations 3
- Additional safety warnings 4
- Additional safety warnings specific for abrasive cutting off operations 4
- English 4
- General safety instructions for grinders 4
- Applications 5
- English 5
- Maintenance and inspection 5
- Mounting and operation 5
- Specifications 5
- Standard accessories 5
- Symbols 5
- English 6
- English 7
- Allgemeine sicherheitshinweise für elektrogeräte 8
- Deutsch 8
- Deutsch 9
- Für schleif und trennschleifarbeiten geltende sicherheitshinweise 9
- Besondere sicherheitshinweise für schleif bzw trennschleifarbeiten 10
- Deutsch 10
- Rückschlag und dazu gehörige sicherheitshinweise 10
- Weitere sicherheitshinweise zu trennschleifarbeiten 10
- Allgemeine sicherheitshinweise für schleifgeräte 11
- Deutsch 11
- Zusätzliche sicherheitswarnungen 11
- Anwendungsgebiete 12
- Deutsch 12
- Montage und betrieb 12
- Standardzubehör 12
- Symbole 12
- Technische daten 12
- Wartung und inspektion 12
- Deutsch 13
- Avertissements de sécurité généraux pour l outil 14
- Français 14
- Avertissements de sécurité courants pour les opérations de meulage ou de découpage par abrasion 15
- Français 15
- Avertissements de sécurité propres aux opérations de découpage par abrasion 16
- Avertissements de sécurité propres aux opérations de meulage et de découpage par abrasion 16
- Français 16
- Recul et avertissements connexes 16
- Avertissements de sécurité supplémentaires 17
- Consignes de sécurité générales pour les meuleuses 17
- Français 17
- Symboles 17
- Accessoires standard 18
- Applications 18
- Caractéristiques 18
- Entretien et vérification 18
- Français 18
- Installation et fonctionnement 18
- Français 19
- Avvertimenti generali di sicurezza sugli utensili elettrici 20
- Italiano 20
- Avvertimenti di sicurezza comuni per le operazioni di smerigliatura o di taglio abrasivo 21
- E il diametro esterno e lo spessore del vostro accessorio devono rientrare entro la capacità nominale dell utensile elettrico 21
- Italiano 21
- Avvertimenti di sicurezza aggiuntivi specifici per le operazioni di taglio abrasivo 22
- Avvertimenti di sicurezza specifici per le operazioni di smerigliatura e di taglio abrasivo 22
- Istruzioni di sicurezza generali per smerigliatrici 22
- Italiano 22
- Rinculo e relative avvertenze 22
- Italiano 23
- Precauzioni di sicurezza aggiuntive 23
- Simboli 23
- Accessori standard 24
- Applicazioni 24
- Caratteristiche 24
- Italiano 24
- Manutenzione ed ispezione 24
- Montaggio e operazione 24
- Italiano 25
- Algemene veiligheidswaarschuwingen voor elektrisch gereedschap 26
- Nederlands 26
- Nederlands 27
- Veiligheidswaarschuwingen voor slijpen en doorslijpen 27
- Aanvullende specifieke veiligheidswaarschuwingen voor doorslijpen 28
- Nederlands 28
- Specifieke veiligheidswaarschuwingen voor slijpen en doorslijpen 28
- Terugslag en daarmee verband houdende waarschuwingen 28
- Aanvullende veiligheidswaarschuwingen 29
- Algemene veiligheidsinstructies voor slijpmachines 29
- Nederlands 29
- Symbolen 29
- Montage en gebruik 30
- Nederlands 30
- Onderhoud en inspectie 30
- Standaard toebehoren 30
- Technische gegevens 30
- Toepassingen 30
- Nederlands 31
- Advertencias de seguridad general de la herramienta eléctrica 32
- Español 32
- Advertencias comunes de seguridad para las operaciones de molido o corte abrasivo 33
- Español 33
- Advertencias de seguridad adicionales específicas para las operaciones de corte abrasivo 34
- Advertencias de seguridad específicas para las operaciones de molido y corte abrasivo 34
- Español 34
- Retroceso y advertencias relacionadas 34
- Advertencias de seguridad adicionales 35
- Español 35
- Instrucciones de seguridad generales para amoladoras 35
- Símbolos 35
- Accessorios estándar 36
- Aplicación 36
- Español 36
- Especificaciones 36
- Mantenimiento e inspección 36
- Montaje y funcionamiento 36
- Español 37
- Avisos gerais de segurança para a ferramenta elétrica 38
- Português 38
- Avisos de segurança comuns para operações de retificação ou corte abrasivo 39
- Português 39
- Recuo e avisos relacionados 39
- Avisos de segurança adicionais específicos para operações de corte abrasivo 40
- Avisos de segurança específicos para operações de retificação ou corte abrasivo 40
- Instruções de segurança gerais para rebarbadoras 40
- Português 40
- Avisos de segurança adicionais 41
- Português 41
- Símbolos 41
- Acessórios padrão 42
- Aplicações 42
- Especificações 42
- Manutenção e inspeção 42
- Montagem e utilização 42
- Português 42
- Português 43
- Allmänna säkerhetsvarningar för elektriska verktyg 44
- Svenska 44
- Kast och tillhörande varningar 45
- Svenska 45
- Säkerhetsvarningar vanliga för slipnings eller slipande kapningsarbeten 45
- Allmänna säkerhetsinstruktioner för vinkelslipar 46
- Svenska 46
- Säkerhetsvarningar speciella för slipnings och slipande kapningsarbeten 46
- Ytterligare säkerhetsvarningar 46
- Ytterligare säkerhetsvarningar för slipande kapningsarbeten 46
- Användningsområden 47
- Montering och användning 47
- Standardtillbehör 47
- Svenska 47
- Symboler 47
- Tekniska data 47
- Svenska 48
- Underhåll och inspektion 48
- Generelle sikkerhedsadvarsler for elektrisk værktøj 49
- Generelle sikkerhedsadvarsler for slibning eller slibende afskæringsfunktioner 50
- Tilbageslag og relaterede advarsler 50
- Ekstra sikkerhedsforskrifter for slibende afskæringsfunktioner 51
- Generelle sikkerhedsforskrifter for vinkelslibere 51
- Særlige sikkerhedsforskrifter for slibning og slibende afskæringsfunktioner 51
- Anvendelse 52
- Ekstra sikkerhedsadvarsler 52
- Specifikationer 52
- Standardtilbehør 52
- Symboler 52
- Montering og anvendelse 53
- Vedligeholdelse og eftersyn 53
- Generelle sikkerhetsforholdsregler for elektroverktøy 55
- Sikkerhetsinstrukser for vanlig sliping og kutt operasjoner 56
- Tilbakeslag og relaterte advarsler 56
- Ekstra sikkerhetsinstrukser spesifikt for kutt operasjoner 57
- Flere sikkerhetsadvarsler 57
- Generelle sikkerhetsinstruksjoner for slipemaskiner 57
- Sikkerhetsinstrukser spesifikt for sliping og kutt operasjoner 57
- Anvendelse 58
- Montering og bruk 58
- Spesifikasjoner 58
- Standard tilbehør 58
- Symboler 58
- Vedlikehold og inspeksjon 59
- Yleiset sähkötyökalun turvallisuutta koskevat varoitukset 60
- Takapotku ja siihen liittyvät varoitukset 61
- Turvallisuutta koskevia varoituksia hiontaa ja katkaisuhiontaa varten 61
- Lisää turvallisuutta koskevia varoituksia 62
- Lisää turvallisuutta koskevia varoituksia katkaisuhiontaa varten 62
- Turvallisuutta koskevia varoituksia erityisesti hiontaa ja katkaisuhiontaa varten 62
- Yleisiä hiomakoneen käyttöä koskevia turvaohjeita 62
- Kiinnittäminen ja käyttö 63
- Perusvarusteet 63
- Sovellukset 63
- Symbolit 63
- Tekniset tiedot 63
- Huolto ja tarkastus 64
- Γενικεσ προειδοποιησεισ ασφαλειασ του ηλεκτρικου εργαλειου 65
- Ελληνικά 65
- Ελληνικά 66
- Κοινεσ προειδοποιησεισ ασφαλειασ για λειανση η εργασιεσ κοπησ 66
- Ειδικεσ προειδοποιησεισ ασφαλειασ για εργασιεσ λειανσησ η κοπησ 67
- Ελληνικά 67
- Οπισθια κινηση και σχετικεσ προειδοποιησεισ 67
- Προσθετεσ ειδικεσ προειδοποιησεισ ασφαλειασ για εργασίεσ λειανσησ η κοπησ 67
- Γενικεσ οδηγιεσ ασφαλειασ για τροχουσ 68
- Ελληνικά 68
- Προσθετεσ προειδοποιησεισ ασφαλειασ 68
- Βασικα εξαρτηματα 69
- Ελληνικά 69
- Εφαρμογεσ 69
- Στερεωση και λειτουργια 69
- Συμβολα 69
- Τεχνικα χαρακτηριστικα 69
- Ελληνικά 70
- Συντηρηση και ελεγχοσ 70
- Ελληνικά 71
- Ogólne wskazówki bezpieczeństwa dotyczące elektronarzędzi 72
- Polski 72
- Ogólne wskazówki bezpieczeństwa dotyczące szlifowania i cięcia 73
- Polski 73
- Dodatkowe wskazówki bezpieczeństwa dotyczące szlifowania i cięcia 74
- Odbicie i powiązane z nim ostrzeżenia 74
- Ogólne wskazówki bezpieczeństwa dotyczące cięcia 74
- Polski 74
- Dodatkowe wskazówki bezpieczeństwa 75
- Ogólne wskazówki bezpieczeństwa dotyczące szlifowania 75
- Polski 75
- Symbole 75
- Akcesoria standardowe 76
- Konserwacja i kontrola 76
- Montaż i praca 76
- Polski 76
- Specyfikacje techniczne 76
- Zastosowania 76
- Polski 77
- A szerszámgéppel kapcsolatos általános biztonsági figyelmeztetések 78
- Magyar 78
- Biztonsági figyelmeztetések csiszoló és vágó műveletekhez 79
- Magyar 79
- Visszarúgás és erre vonatkozó figyelmeztetések 79
- A csiszolási és darabolási műveletekre vonatkozó biztonsági figyelmeztetések 80
- A daraboló műveletekre vonatkozó kiegészítő biztonsági figyelmeztetések 80
- Csiszolókra vonatkozó általános biztonsági utasítások 80
- Magyar 80
- Magyar 81
- Szimbólumok 81
- További biztonsági figyelmeztetések 81
- Alkalmazási területek 82
- Karbantartás és ellenőrzés 82
- Magyar 82
- Műszaki adatok 82
- Szabványos kiegészítők 82
- Összeszerelés és használat 82
- Magyar 83
- Obecná bezpečnostní varování týkající se bezpečnosti elektrického nánářadí 84
- Čeština 84
- Bezpečnostní varování společné pro broušení a abrazivní řezání 85
- Upozornění na zpětný ráz 85
- Čeština 85
- Bezpečnostní varování pro broušení a řezání 86
- Doplňující bezpečnostní varování pro řezání 86
- Všeobecné bezpečnostní pokyny pro brusky 86
- Čeština 86
- Další bezpečnostní varování 87
- Použití 87
- Specifikace 87
- Standardní příslušenství 87
- Symboly 87
- Čeština 87
- Montáž a provoz 88
- Údržba a kontrola 88
- Čeština 88
- Genel elektri kli alet güvenli k uyarilari 89
- Türkçe 89
- Geri tepme ve i lgi li uyarilar 90
- Taşlama veya aşindirarak kesme i şlemleri i çi n genel güvenli k uyarilari 90
- Türkçe 90
- Aşindirarak kesme i şlemleri i çi n özel i lave güvenli k uyarilari 91
- Kalipçi taşlamalar i çi n genel güvenli k tali matlari 91
- Taşlama ve aşindirarak kesme i şlemleri i çi n özel güvenli k uyarilari 91
- Türkçe 91
- I lave güvenli k uyarilari 92
- Semboller 92
- Standart aksesuarlar 92
- Tekni k özelli kler 92
- Türkçe 92
- Uygulamalar 92
- Bakim ve muayene 93
- Montaj ve çaliştirma 93
- Türkçe 93
- Avertismente generale privind siguranţa sculelor electrice 94
- Română 94
- Avertismente de siguranţă generale pentru operaţiunile de șlefuire sau tăiere abrazivă 95
- Reculul și avertismentele aferente 95
- Română 95
- Avertismente de siguranţă specifice pentru operaţiunile de șlefuire și tăiere abrazivă 96
- Avertismente suplimentare de siguranţă specifice pentru operaţiunile tăiere abrazivă 96
- Instrucţiuni generale de siguranţă pentru polizoare 96
- Română 96
- Accesorii standard 97
- Aplicaţii 97
- Avertismente suplimentare privind siguranţa 97
- Română 97
- Simboluri 97
- Specificaţii 97
- Asamblare și operare 98
- Română 98
- Întreţinere și verificare 98
- Română 99
- Slovenščina 100
- Splošna varnostna navodila za električna orodja 100
- Povratni udarec in ustrezna opozorila 101
- Slovenščina 101
- Varnostna opozorila značilna za brušenje ali rezanje 101
- Dodatna varnostna opozorila 102
- Dodatna varnostna opozorila za rezanje 102
- Slovenščina 102
- Splošna varnostna navodila za brusilnike 102
- Varnostna opozorila za brušenje in rezanje 102
- Namestitev in delovanje 103
- Simboli 103
- Slovenščina 103
- Specifikacije 103
- Standardna pribor 103
- Uporaba 103
- Slovenščina 104
- Vzdrževanje in pregledovanje 104
- Slovenčina 105
- Všeobecné bezpečnostné výstrahy pre elektrické náradie 105
- Bezpečnostné výstrahy spoločné pre činnosti brúsenia a rozbrusovania 106
- Slovenčina 106
- Spätný náraz a príslušné varovania 106
- Bezpečnostné výstrahy charakteristické pre činnosti brúsenia a rozbrusovania 107
- Dodatočné bezpečnostné výstrahy charakteristické pre činnosti brúsenia a rozbrusovania 107
- Slovenčina 107
- Všeobecné bezpečnostné pokyny pre brúsky 107
- Slovenčina 108
- Symboly 108
- Ďalšie bezpečnostné varovania 108
- Štandardné príslušenstvo 108
- Montáž a obsluha 109
- Použitie 109
- Slovenčina 109
- Technické parametre 109
- Údržba a kontrola 109
- Slovenčina 110
- Български 111
- Общи мерки за безопасност при използване на електрически инструменти 111
- Български 112
- Предупреждения за безопасност общи за операции включващи шлифоване или абразивно рязане 112
- Български 113
- Допълнителни предупреждения за безопасност специфични за операции включващи абразивно рязане 113
- Предупреждения за безопасност специфични за операции включващи шлифоване или абразивно рязане 113
- Предупреждения за откат и свързани с това опасности 113
- Български 114
- Допълнителни предупреждения за безопасност 114
- Общи инструкции за безопасност за шлайфмашини 114
- Български 115
- Монтаж и експлоатация 115
- Поддръжка и инспекция 115
- Приложения 115
- Символи 115
- Спецификации 115
- Стандартни аксесоари 115
- Български 116
- Opšta bezbednosna upozorenja za električni alat 117
- Srpski 117
- Bezbednosna upozorenja za postupke brušenja ili abrazivnog sečenja 118
- Povratni udar i slična upozorenja 118
- Srpski 118
- Bezbednosna upozorenja specifična za postupke brušenja i abrazivnog sečenja 119
- Dodatna bezbednosna upozorenja specifična za postupke abrazivnog sečenja 119
- Opšta bezbednosna uputstva za brusilice 119
- Srpski 119
- Dodatna bezbednosna upozorenja 120
- Oznake 120
- Primene 120
- Specifikacije 120
- Srpski 120
- Standardni pribor 120
- Montaža i upotreba 121
- Održavanje i provera 121
- Srpski 121
- Hrvatski 122
- Općenita sigurnosna upozorenja za električne alate 122
- Hrvatski 123
- Povratni udar i povezana upozorenja 123
- Sigurnosna upozorenja za sve operacije brušenja ili abrazivnog rezanja 123
- Dodatna sigurnosna upozorenja 124
- Dodatna sigurnosna upozorenja specifična za operacije abrazivnog rezanja 124
- Hrvatski 124
- Opće sigurnosne upute za brusilice 124
- Sigurnosna upozorenja specifična za operacije brušenja i abrazivnog rezanja 124
- Hrvatski 125
- Montaža i rad 125
- Održavanje i inspekcija 125
- Simboli 125
- Specifikacije 125
- Standardna oprema 125
- Vrste primjene 125
- Hrvatski 126
- Загальні інструкції безпеки електричного інструменту 127
- Українська 127
- Загальні попередження про обережність для проведення шліфувальних робіт або відрізання 128
- Українська 128
- Віддача і пов язані з нею небезпеки 129
- Додаткові заходи безпеки спеціально для абразивного різання 129
- Заходи безпеки під час шліфування і абразивного обрізування 129
- Українська 129
- Додаткові правила безпеки 130
- Загальні інструкції безпеки для шліфувальної машини 130
- Символи 130
- Українська 130
- Області застосування 131
- Стандартні аксесуари 131
- Технічне обслуговування і перевірка 131
- Технічні характеристики 131
- Українська 131
- Установка та експлуатація 131
- Українська 132
- Общие правила безопасности при работе с электроинструментом 133
- Русский 133
- Общие предупреждения об осторожности для проведения шлифовальных работ или отрезания 134
- Русский 134
- Особые меры предосторожности для режущих работ и абразивной отрезки 135
- Отдача и другие похожие предупреждения 135
- Русский 135
- Дополнительные особые меры предосторожности для абразивной отрезки 136
- Общие инструкции по технике безопасности для шлифовальных машин 136
- Русский 136
- Дополнительные указания по обеспечению безопасности 137
- Русский 137
- Символы 137
- Назначение 138
- Русский 138
- Стандартные принадлежности 138
- Технические характеристики 138
- Техническое обслуживание и осмотр 138
- Установка и эксплуатация 138
- Русский 139
- Book_g18mr indb 145 0000book_g18mr indb 145 2017 11 29 10 58 05 2017 11 29 10 58 05 145
- Certificado de garantia 145
- Certificado de garantía 145
- Certificat de garantie 145
- Certificat de garanţie 145
- Certificato di garanzia 145
- Deutsch norsk slovenščina 145
- English dansk română 145
- Español magyar hrvatski 145
- Français suomi slovenčina 145
- Garancia bizonylat 145
- Garancijsko potrdilo 145
- Garanti serti fi kasi 145
- Garantibevis 145
- Garanticertifikat 145
- Garantiebewijs 145
- Garantieschein 145
- Garantisertifikat 145
- Garantni sertifikat 145
- Guarantee certificate 145
- Gwarancja 145
- Italiano ελληνικά български 145
- Jamstveni certifikat 145
- Nederlands polski srpski 145
- Português čeština український 145
- Svenska türkçe русский 145
- Takuutodistus 145
- Záruční list 145
- Záručný lista 145
- Πιστοποιητικο εγγυησησ 145
- Гарантийный сертификат 145
- Гарантійний сертифікат 145
- Гаранционен сертификат 145
- Hikoki power tools belgium n v s a 147
- Hikoki power tools czech s r o 147
- Hikoki power tools denmark a s 147
- Hikoki power tools deutschland gmbh 147
- Hikoki power tools finland oy 147
- Hikoki power tools france s a s 147
- Hikoki power tools hungary kft 147
- Hikoki power tools italia s p a 147
- Hikoki power tools lbérica s a 147
- Hikoki power tools netherlands b v 147
- Hikoki power tools norway as 147
- Hikoki power tools polska sp z o o 147
- Hikoki power tools romania s r l 147
- Hikoki power tools rus l l c 147
- Hikoki power tools sweden ab 147
- Hikoki power tools u k ltd 147
- Hikoki power tools österreich gmbh 147
- 2018 naoto yamashiro european standard manager 150
- A nakagawa corporate offi cer 150
- Deutsch español 150
- English nederlands 150
- Français português 150
- Head offi ce in japan 150
- Hikoki power tools deutschland gmbh 150
- Italiano svenska 150
- Koki holdings co ltd 150
- Representative offi ce in europe 150
- Shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan 150
- Siemensring 34 47877 willich germany 150
- 2018 naoto yamashiro european standard manager 151
- A nakagawa corporate offi cer 151
- Dansk polski 151
- Head offi ce in japan 151
- Hikoki power tools deutschland gmbh 151
- Koki holdings co ltd 151
- Norsk magyar 151
- Representative offi ce in europe 151
- Shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan 151
- Siemensring 34 47877 willich germany 151
- Suomi čeština 151
- Ελληνικά türkçe 151
- 2018 naoto yamashiro european standard manager 152
- A nakagawa corporate offi cer 152
- Code no c99702172 m printed in malaysia 152
- Head offi ce in japan 152
- Hikoki power tools deutschland gmbh 152
- Koki holdings co ltd 152
- Representative offi ce in europe 152
- Română srpski 152
- Shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan 152
- Siemensring 34 47877 willich germany 152
- Slovenčina український 152
- Slovenščina hrvatski 152
- Български русский 152
Похожие устройства
- Hikoki RH 650V Инструкция по эксплуатации
- Hikoki RH 600T Инструккция по эксплуатации
- Hikoki M 8V2 Инструкция по эксплуатации
- Hikoki M 8SA2 Инструкция по эксплуатации
- Hikoki M 12VE Инструкция по эксплуатации
- Hikoki M 12V2 Инструкция по эксплуатации
- Hikoki M 12SA2 Инструкция по эксплуатации
- Hikoki SV 13YB Инструкция по эксплуатации
- Hikoki SV 13YA Инструкция по эксплуатации
- Hikoki SV 12SH Инструкция по эксплуатации
- Hikoki SV 12SG Инструкция по эксплуатации
- Hikoki SV 12SD Инструкция по эксплуатации
- Hikoki SP 18VA Инструкция по эксплуатации
- Hikoki SB 8V2 Инструкция по эксплуатации
- Hikoki GP 3V Инструкция по эксплуатации
- Hikoki GP 2S2 Инструкция по эксплуатации
- Hikoki W 6V4 Инструкция по эксплуатации
- Tech ST-81 Инструкция по эксплуатации
- Tech ST-81 zPID Инструкция по эксплуатации
- Tech ST-880 zPID Инструкция по эксплуатации