![COM BBF-2 — schematic Drawing and Timing Chart for Circuit Board Control [10/13]](/icons/site-icon-64.png){kind=icon}
COM BBF-2 — schematic Drawing and Timing Chart for Circuit Board Control [10/13]
Превью страниц
Страница 10 /
13
![COM BBF-2 [10/13] Outfee ding roller](/views2/1500408/page10/bga.png)
10. SCHEMATIC DRAWING OF PRINTED CIRCUIT BOARD,
CONNECTOR AND CONTROL
11. TIMING CHART
タイミングチャート
CN3 CAM SIGNAL INPUT
CN13
CAM MOTOR DONDENSOR
CN12
CAM MOTOR OUTPUT
CN10
ROLLER MOTOR OUTPUT
CN11
ROLLER MOTOR CONDENSOR
CN8
TORQUE ADJ. INPUT
(VR)
CN2
SW. PCB INPUT
CN4 AUTO SIGNAL INPUT
VR2 TEMP. COMP.ADJ.
LED DISPLAY
CN17 AC POWER INPUT
CN14 HEATER OUTPUT
CN15 AC POWER SWITCH
CN19 5V INPUT
CN7 EXTERNAL START INPUT
CN6 DOOR OPEN-CLOSE SIGNAL
LED4 CAM MOTOR BRAKE
LED3 CAM MOTOR DRIVE
LED2 ROLLER MOTOR RUN FWD.
LED1 ROLLER MOTOR RUN REV.
LED5 HEATER ON
CN16 AC POWER SUB OUTPUT
HEATE
R
CONTR
OL
DRIVE
CAM
OUTFEE
DING
ROLLER
TENSION
ING
ROLLER
OUT FEEDING
TENSIONING
ONE CYCLE
1.4sec.
0.8sec.
AC1V
Содержание
37- Contents
- Contents
- Introduction
- Compact automatic taping machine
- Contents in each carton
- Sketch drawing
- Open the front panel
- Do not allow the tape head to be protruded
- When power is already supplied the start lamp will be switched of
- The upper and the lower rollers feeding it further between the upper and the lower tape clamps pull out the tape about 60 cm reset the tape width setting plate
- The start lamp will flicker if the main power switch has been turned on put a tape reel on to the core holder make sure the unreeling direction is correct
- Tape feeding
- Shut the front panel and press the power switch
- Make a loop between the both guides left and right
- Insert the tape head between the spacer and the beak do not allow the tape head to be protruded from the right edge of the spacer the top of the loop should come to a position a little higher than the guide top face refer to a indicated in the sketch shown below
- Grip the tape head pull the width setting plate toward you feed the tape between
- Operating instructions
- Auto mode
- Sealing temperature adjustment
- Banding tension adjustment
- Specifications
- Outfee ding roller
- Heate r
- タイミングチャート
- Timing chart
- Tension ing roller
- Schematic drawing of printed circuit board
- Drive cam
- Contr ol
- Connector and control
- Warning to prevent damage which may result in fire or shock
- If any trouble occurs while you are using the machine turn of the machine and contact your dealer if you continue to use the machine when there is something wrong with it the trouble may become much worse
- Hazard do not expose this machine to rain or moisture
- Do not touch internal parts be sure not to touch the internal parts that will be cause of accident should you notice any trouble
- Precautions for use and installation
- Important safety notice
- Warranty
Похожие устройства
-
COM PAИнструкция по эксплуатации -
COM JE-150FИнструкция по эксплуатации -
COM JE-240Инструкция по эксплуатации
-
Cassida 5550 uvИнструкция к устройству -
DoCash 3040Руководство по работе с устройством -
Dors 800Инструкция пользователя -
Dors 750Инструкция к устройству
-
Dors 700Эксплуатационная инструкция
-
Dors 620Инструкция по работе -
Dors 600Руководство по эксплуатации
-
PRO 15Руководство по настройке -
BILLCON CHS-10Инструкция по эксплуатации
Explore the detailed schematic drawing and timing chart for printed circuit board control, including motor outputs, signal inputs, and LED indicators for efficient operation.