![COM BBF-2 [12/13] Warning to prevent damage which may result in fire or shock](/icons/site-icon-64.png){kind=icon}
COM BBF-2 [12/13] Warning to prevent damage which may result in fire or shock
Превью страниц
Страница 12 /
13
![COM BBF-2 [12/13] Warning to prevent damage which may result in fire or shock](/views2/1500408/page12/bgc.png)
13. IMPORTANT SAFETY NOTICE
!.")!*
3!!!*
!!
? 2!? N
!"):"
!
<A4：916A1G19;71B19G;，
6491,-1-19（9%<;）
4A19819-1<%B1+<9461
9171919-4=JA<B71619-1+19441B
C!" 3!!
!!
"
"/20
14. PRECAUTIONS FOR USE AND INSTALLATION
((E(E(
@<944= ： 2 " " ! '
H*C""．
1!)!!
In the absence of grounding, a technical fault could be lethal.
Switch the machine off and disconnect the power cable if you change blown fuses.
<!!)!!
2!)"
"!!)"2!"!2!
A!'"
6!"
"2"""#E"'
%2"""*)
!"")
G ， "!)E#
2*)("
5!
!! " H! )! :
"
<!!2"!!))3!'2!
6!
%! ． !!)
!)!
)!!"*5"
!
If you continue to use the machine when there is something wrong with it, the trouble may become much worse.
Содержание
37- Contents
- Contents
- Introduction
- Compact automatic taping machine
- Contents in each carton
- Sketch drawing
- Open the front panel
- Do not allow the tape head to be protruded
- When power is already supplied the start lamp will be switched of
- The upper and the lower rollers feeding it further between the upper and the lower tape clamps pull out the tape about 60 cm reset the tape width setting plate
- The start lamp will flicker if the main power switch has been turned on put a tape reel on to the core holder make sure the unreeling direction is correct
- Tape feeding
- Shut the front panel and press the power switch
- Make a loop between the both guides left and right
- Insert the tape head between the spacer and the beak do not allow the tape head to be protruded from the right edge of the spacer the top of the loop should come to a position a little higher than the guide top face refer to a indicated in the sketch shown below
- Grip the tape head pull the width setting plate toward you feed the tape between
- Operating instructions
- Auto mode
- Sealing temperature adjustment
- Banding tension adjustment
- Specifications
- Outfee ding roller
- Heate r
- タイミングチャート
- Timing chart
- Tension ing roller
- Schematic drawing of printed circuit board
- Drive cam
- Contr ol
- Connector and control
- Warning to prevent damage which may result in fire or shock
- If any trouble occurs while you are using the machine turn of the machine and contact your dealer if you continue to use the machine when there is something wrong with it the trouble may become much worse
- Hazard do not expose this machine to rain or moisture
- Do not touch internal parts be sure not to touch the internal parts that will be cause of accident should you notice any trouble
- Precautions for use and installation
- Important safety notice
- Warranty
Похожие устройства
-
COM PAИнструкция по эксплуатации -
COM JE-150FИнструкция по эксплуатации -
COM JE-240Инструкция по эксплуатации
-
Cassida 5550 uvИнструкция к устройству -
DoCash 3040Руководство по работе с устройством -
Dors 800Инструкция пользователя -
Dors 750Инструкция к устройству
-
Dors 700Эксплуатационная инструкция
-
Dors 620Инструкция по работе -
Dors 600Руководство по эксплуатации
-
PRO 15Руководство по настройке -
BILLCON CHS-10Инструкция по эксплуатации