![Danfoss FCM 340 [4/112] Fcm 300 series](/img/pdf.png)
Danfoss FCM 340 [4/112] Fcm 300 series
![Danfoss FCM 315 [4/112] Fcm 300 series](/views2/1560956/page4/bg4.png)
FCM 300 Series
MG.03.B7.02 - VLT is a registered Danfoss trademark4
Safety
All operations must be carried out by
appropriately trained personel.
Use all lifting facilities provided e.g. both lifting points
if fitted or single lifting point if fitted*.
Vertical lifting - Prevent uncontrolled rotation.
Lift machine - Do not lift other equipment with motor
lifting points only.
Before installation check for fan cover damage, shaft
damage, foot/mounting damage, and loose fasteners.
Check nameplate details.
Ensure level mounting surface, balanced mounting,
not misaligned.
Gaskets, and/or sealants, and guards must be
correctly fitted.
Correct belt tension.
Please observe derating rules, see "Special
conditions".
*Note: maximum hand lift is 20 kg below
shoulder, but above ground level. Max.
gross weights:
- Frame size 80: 15 kg
- Frame size 90 & 100: 30 kg
- Frame size 112: 45 kg
- Frame size 132: 80 kg
The voltage on the FC motor is
dangerous when the motor is connected
to mains. Incorrect installation of the FC
motor may lead to material damage or serious injury,
or it may be fatal.
Consequently, the instructions in this manual as well
as national and local rules and safety regulations
must be complied with.
Touching the electrical parts may be fatal, even after
the mains supply has been disconnected.
Wait at least 4 minutes.
- Installation must be fused and isolated correctly.
- Covers and cable entries must be fitted.
NB!
It is the user's or certified electrician's
responsibility to ensure correct earthing and
protection in accordance with applicable national and
local requirements and standards.
■ Safety regulations
1. The VLT
®
DriveMotor (FC motor) must be
disconnected from mains if repair work is to be
carried out.
Check that the mains supply has been
disconnected and that the necessary time has
passed (4 minutes).
2. Correct protective earthing of the equipment
must be established, the user must be
protected against supply voltage, and the motor
must be protected against overload in
accordance with applicable national and local
regulations.
Use of RCD's (ELCB relays) is described in
chapter 10.
3. The earth leakage currents are higher than
3.5 mA. This means that the FC motor requires
a fixed, permanent installation as well as
reinforced protective earthing.
■ Warning against unintended start
1. The motor can be brought to a stop by means of
digital commands, bus commands, or
references, while the frequency converter is
connected to mains.
If personal safety considerations make it
necessary to ensure that no unintended start
occurs,
these stop functions are not sufficient.
2. While parameters are being changed, the motor
may start.
3. A motor that has been stopped may start if
faults occur in the electronics of the FC motor, or if a
temporary overload or a fault in the mains supply
ceases.
Содержание
- Contents 1
- Fcm 300 series 1
- Fcm 300 series 2
- Symbols 2
- Fcm 300 series 3
- Safety 3
- Fcm 300 series 4
- Safety 4
- Fcm 300 series 5
- Introduction 5
- Available literature the chart below gives an overview of the literature available for the fcm 300 series 6
- Design guide gives all required information for design purposes and gives a good insight into the product concept product range technical data control programming etc 6
- Fcm 300 series 6
- If you have any questions concerning fcm 300 series please call us we have drive specialists all over the world ready to advise you on applications programming training and service 6
- Introduction 6
- Promotion 6
- Quick setup helps the users to quickly get their fcm 300 series motor unit installed and running 6
- Specific technical publications on the fcm 300 series 6
- The quick setup is always delivered with the unit 6
- Fcm 300 series 7
- Product concept 7
- Fcm 300 series 8
- Product concept 8
- Fcm 300 series 9
- Selection of fc motor 9
- Fcm 300 series 10
- Selection of fc motor 10
- Fcm 300 series 11
- Flange size according to iec ref ffxxx dimension m in chapter 6 s available as standard shaft a available as an alternative with specially elongated shaft to provide standard shaft for frame b available as an alternative with standard shaft for frame requiring no modification 11
- I ordering info for frames and flanges 11
- I ordering info for inverter box position and drain hole position 11
- Selection of fc motor 11
- Fcm 300 series 12
- Ordered by 12
- Selection of fc motor 12
- Fcm 300 series 13
- Technical data 13
- Fcm 300 series 14
- Technical data 14
- Fcm 300 series 15
- Technical data 15
- Fcm 300 series 16
- Technical data 16
- Fcm 300 series 17
- Technical data 17
- Fcm 300 series 18
- Fcm 300 series 19
- Mechanical specifications 19
- Fcm 300 series 20
- Mechanical specifications 20
- Fcm 300 series 21
- Mechanical specifications 21
- Fcm 300 series 22
- I dimensions 22
- Mechanical specifications 22
- Pole motor 37 5 22
- Pole motor 53 22
- Fcm 300 series 23
- Max length of mounting bolts penetrating the b14 flange 23
- Mechanical specifications 23
- Fcm 300 series 24
- Mechanical specifications 24
- Fcm 300 series 25
- Mechanical specifications 25
- Fcm 300 series 26
- Mechanical specifications 26
- Fcm 300 series 27
- Mechanical specifications 27
- Fcm 300 series 28
- Mechanical specifications 28
- Fcm 300 series 29
- Local control 29
- 12345678901234567890 30
- Fcm 300 series 30
- Local control 30
- Fcm 300 series 31
- Local control 31
- Fcm 300 series 32
- Frequency 32
- Local control 32
- Motor is running 32
- Status 32
- Var 1 var 1 var 1 32
- 30 13 a 33
- English 33
- Fcm 300 series 33
- Language 33
- Local control 33
- Motor is running 33
- Quick menu x of y 33
- Ref torque curr a 33
- English 34
- Fcm 300 series 34
- Frequency 34
- Language 34
- Language english 34
- Local control 34
- Fcm 300 series 37
- Local control 37
- Yellow green 37
- Can be orange in some cables 38
- Fcm 300 series 38
- I local operation pad lop 175n0128 ip65 38
- I remote mounting kit cont panel door control unit 38
- Local control 38
- Local operation panel lop 175n0128 ip 65 fixture for lop 175n1114 38
- Use the keys to set reference 38
- After fitting cut off or isolate excess wire 39
- At power up the unit will always be in stop mode set reference will be stored during power down if permanent start mode is desired connect terminal 6 to terminal 4 and do not connect purple grey wire to terminal 4 this means the stop function on lop is disabled 39
- Fcm 300 series 39
- Mg 3 b7 2 vlt is a registered danfoss trademark 39
- Fcm 300 series 41
- Parameters 41
- Fcm 300 series 42
- Operation display 42
- Fcm 300 series 43
- Operation display 43
- Fcm 300 series 44
- Operation display 44
- Fcm 300 series 45
- Operation display 45
- Fcm 300 series 46
- Operation display 46
- Fcm 300 series 47
- Operation display 47
- Fcm 300 series 48
- Load and motor 48
- Fcm 300 series 49
- Load and motor 49
- Fcm 300 series 50
- Load and motor 50
- Fcm 300 series 51
- Load and motor 51
- Fcm 300 series 52
- References and limits 52
- Fcm 300 series 53
- References and limits 53
- Fcm 300 series 54
- References and limits 54
- Fcm 300 series 55
- References and limits 55
- Fcm 300 series 56
- References and limits 56
- Fcm 300 series 57
- References and limits 57
- Fcm 300 series 58
- Inputs and outputs 58
- Fcm 300 series 59
- Inputs and outputs 59
- Fcm 300 series 60
- Inputs and outputs 60
- Fcm 300 series 61
- Inputs and outputs 61
- Fcm 300 series 62
- Inputs and outputs 62
- Fcm 300 series 63
- Inputs and outputs 63
- Fcm 300 series 64
- Special functions 64
- Fcm 300 series 65
- Special functions 65
- Fcm 300 series 66
- Special functions 66
- Fcm 300 series 67
- Special functions 67
- Fcm 300 series 68
- Special functions 68
- Fcm 300 series 69
- Serial communication 69
- Fcm 300 series 70
- Serial communication 70
- Fcm 300 series 71
- Serial communication 71
- Fcm 300 series 72
- Serial communication 72
- Fcm 300 series 73
- Serial communication 73
- Fcm 300 series 74
- Serial communication 74
- Fcm 300 series 75
- Technical functions 75
- Fcm 300 series 76
- Technical functions 76
- Fcm 300 series 77
- Technical functions 77
- Fcm 300 series 78
- Technical functions 78
- Fcm 300 series 79
- Serial communication 79
- Fcm 300 series 80
- Serial communication 80
- Fcm 300 series 81
- Serial communication 81
- Fcm 300 series 82
- Serial communication 82
- Fcm 300 series 83
- Serial communication 83
- Fcm 300 series 84
- Serial communication 84
- Fcm 300 series 85
- Serial communication 85
- Fcm 300 series 86
- Serial communication 86
- Fcm 300 series 87
- Serial communication 87
- Fcm 300 series 88
- Serial communication 88
- Fcm 300 series 89
- Special conditions 89
- Fcm 300 series 90
- Special conditions 90
- Fcm 300 series 91
- Special conditions 91
- Fcm 300 series 92
- Special conditions 92
- Fcm 300 series 93
- Special conditions 93
- 0 since cos 1 94
- Fcm 300 series 94
- Special conditions 94
- Fcm 300 series 95
- Special conditions 95
- Fcm 300 series 96
- Special conditions 96
- Aggressive environments 97
- Fcm 300 series 97
- Fcm 300 series 99
- Warnings and alarms 99
- Fcm 300 series 100
- Warnings and alarms 100
- Dc link voltage low 101
- Fcm 300 series 101
- Torque limit 101
- Trip reset 101
- Warn 6 alarm 12 101
- Warnings and alarms 101
- Fcm 300 series 102
- Warnings and alarms 102
- Alarm messages 103
- Fcm 300 series 103
- Fcm 300 series 105
- List of parameters 105
- Fcm 300 series 106
- List of parameters 106
- Fcm 300 series 107
- List of parameters 107
- Fcm 300 series 108
- List of parameters 108
- Fcm 300 series 109
- Fcm 300 series 110
- Fcm 300 series 111
- Fcm 300 series 112
Похожие устройства
- Danfoss FCM 340 Руководство по проектированию
- Valtec VT.225K.N.E04050 Технический паспорт
- Valtec VT.225K.N.E04100 Технический паспорт
- Danfoss FCM 355 Инструкция по эксплуатации
- Danfoss FCM 355 Руководство по проектированию
- Danfoss FCM 375 Инструкция по эксплуатации
- Danfoss FCM 375 Руководство по проектированию
- Valtec VT.1000.0.0 Технический паспорт
- Valtec VT.1500.0.0 Технический паспорт
- Valtec VT.3000.0.0 Технический паспорт
- Valtec VT.5000.0.0 Технический паспорт
- Valtec VT.5010.0.0 Технический паспорт
- Valtec VT.AS1000 EQUICALOR Инструкция по эксплуатации
- Valtec VT.TE3040.0.220 Технический паспорт
- Valtec VT.TE3040.A.220 Технический паспорт
- Valtec VT.TE3041.0.024 Технический паспорт
- Valtec VT.TE3041.A.024 Технический паспорт
- Valtec VT.TE3042.0.220 Технический паспорт
- Valtec VT.TE3042.A.220 Технический паспорт
- ICI Caldaie REX F 7 Инструкция по эксплуатации