![Invertek Drives ODE-2-34075-3K04 [18/24] P 00 read only drive status parameters](/img/pdf.png)
Invertek Drives ODE-2-34075-3K04 [18/24] P 00 read only drive status parameters
![Invertek Drives ODE-2-12075-1K01 [18/24] P 00 read only drive status parameters](/views2/1583971/page18/bg12.png)
18 Optidrive E2 IP66 / NEMA 4X User Guide
www.invertek.co.uk
Adjusting the Voltage / Frequency (V/f) characteristics
The V/f characteristic is defined by several parameters as shown. Reducing the voltage at a
particular frequency reduces the current in the motor and hence the torque and power. The
V/f curve can be further modified by using P-28 and P-29, where P-28 determines the
percentage increase or decrease of the voltage applied to the motor at the frequency
specified in P-29. This can be useful if motor instability is experienced at certain frequencies,
if this is the case increase or decrease the voltage (P-28) at the speed of instability (P-29).
For applications requiring energy saving, typically HVAC and pumping, the energy optimiser
(P-06) parameter can be enabled. This automatically reduces the applied motor voltage on
light load.
P-00 Read Only Drive Status Parameters
Description
Display range
Explanation
1st Analog input value
0 … 100%
100% = max input voltage
2nd Analog input value
0 … 100%
100% = max input voltage
Speed reference input
-P1-01 … P1-01
Displayed in Hz if P-10 = 0, otherwise displayed in RPM
Digital input status
Binary value
Drive digital input status
Reserved
0
Reserved
Reserved
0
Reserved
Applied motor voltage
0 … 600V AC
Value of RMS voltage applied to motor
DC bus voltage
0 … 1000V dc
Internal DC bus voltage
Internal Heatsink
temperature
-20 … 100 °C
Temperature of heatsink in
°
C
Hours run meter
0 to 99 999 hours
Not affected by resetting factory default parameters
Run time since last trip (1)
0 to 99 999 hours
Run-time clock stopped by drive disable (or trip), reset on
next enable only if a trip occurred. Reset also on next
enable after a drive power down.
Run time since last trip (2)
0 to 99 999 hours
Run-time clock stopped by drive disable (or trip), reset on
next enable only if a trip occurred (under-volts not
considered a trip) – not reset by power down / power up
cycling unless a trip occurred prior to power down
Run time since last disable
0 to 99 999 hours
Run-time clock stopped on drive disable, value reset on
next enable
Drive Effective Switching
Frequency
4 to 32 kHz
Actual drive effective output switching frequency. This
value maybe lower than the selected frequency in P-17 if
the drive is too hot. The drive will automatically reduce the
switching frequency to prevent an over temperature trip
and maintain operation.
DC bus voltage log
0 … 1000V
8 most recent values prior to trip, updated every 250ms
Thermistor temperature
log
-20 … 120 °C
8 most recent values prior to trip, updated every 500ms
Motor current
0 to 2x rated
current
8 most recent values prior to trip, updated every 250ms
Software ID, IO & motor
ctrl
e.g. “1.00”,
“47AE”
Version number and checksum.
“1” on LH side indicates I/O processor,
“2“ indicates motor control
Drive serial number
000000 … 999999
00-000 … 99-999
Unique drive serial number
e.g. 540102 / 32 / 005
Drive identifier
Drive rating
Drive rating, drive type
e.g. 0.37, 1 230,3P-out
7.2.1. Parameter group zero access and navigation
When P-14 = P-37, all P-00 parameters are visible. Default value is 101.
When the user scrolls to P-00, pressing will display “”, where represents the secondary number within P-00. (i.e. 1 to
20). The User can then scroll to the required P-00 parameter.
Pressing once more will then display the value of that particular group zero parameter.
For those parameters which have multiple values (e.g. software ID), pressing the and keys will display the different values within
that parameter.
Pressing returns to the next level up. If is then pressed again (without pressing or ), the display changes to the next level
up (main parameter level, i.e. P-00).
If or is pressed whilst on the lower level (e.g. P00-05) to change the P-00 index, pressing <NAVIGATE> quickly displays that
parameter value.
Содержание
- Company information 2
- Declaration of conformity 2
- Electromagnetic compatibility 2
- Analog and digital input configurations 19 3
- Control wiring 12 3
- General information and ratings 5 3
- Introduction 4 3
- Mechanical installation 6 3
- Operation 12 3
- Parameters 15 3
- Power wiring 8 3
- Technical data 22 3
- Troubleshooting 22 3
- Important safety information 4
- Introduction 4
- 115v 10 1 phase input 3 phase 230v output voltage doubler 5
- 240v 10 1 phase input 5
- 240v 10 3 phase input 5
- 480v 10 3 phase input 5
- Drive model numbers 5
- Each drive can be identified by its model number as shown in figure 1 drive model number format the model number is on the shipping label and the drive nameplate the model number includes the drive and any options drive model numbers for the optidrive e2 drives are provided in 10 rating tables 5
- Figure 1 drive model number format 5
- For ip66 nema 4x with switches switched change the for a y at the end of the product code for ip66 nema 4x without switches non switched change the for a x at the end of the product code 5
- General information and ratings 5
- Identifying the drive by model number 5
- Optidrive e2 ip66 nema 4x user guide 5
- This chapter contains information about the optidrive e2 including how to identify the drive 5
- Www invertek co uk 5
- A b d e f g h i j 6
- Avoid condensation built up in the drive the washdown process of the drive may create a temperature and humidity change avoid condensation built up in the drive the washdown process of the drive may create a temperature and humidity change in and around the drive if the unit is mounted in a cool environment and washed down with higher temperature water as the drive cools to room temperature condensation can form inside the drive especially around the display to prevent this from happening avoid using sealed connectors around rubber coated cables to seal the drive these do not allow any air transfer and hence create a level of condensation and humidity that exceeds the drive s rating 6
- Control terminal torque settings of 0 nm 4 lb in power terminal torque settings of 1 nm 9 lb in 6
- Drive size 6
- Ensure that all terminals are tightened to the appropriate torque setting ensure that all terminals are tightened to the appropriate torque setting 6
- General 6
- Install the optidrive on a flat vertical flame resistant vibration free mounting if higher ip nema ratings are required mount install the optidrive on a flat vertical flame resistant vibration free mounting if higher ip nema ratings are required mount within a suitable enclosure according to en60529 6
- Mechanical dimensions and mounting 6
- Mechanical installation 6
- Mm in mm in mm in mm in mm in mm in mm in mm in mm in 6
- Mount the drive vertically and do not restrict the air flow to the heat sink fins the drive generates heat allow sufficient space mount the drive vertically and do not restrict the air flow to the heat sink fins the drive generates heat allow sufficient space around the unit for heat dissipation do not mount the drive near heat radiating elements or in direct sunlight 6
- Optidrive e2 ip66 nema 4x user guide 6
- Store the optidrive in its box until required storage should be clean and dry and within the temperature range 40 c to 60 c 6
- The ip66 nema 4x drive is intended for indoor use only the ip66 nema 4x drive is intended for indoor use only 6
- The ip66 nema 4x optidrives can be installed side by side the ip66 nema 4x optidrives can be installed side by side with their heatsink flanges touching this gives adequate ventilation space between drives if the optidrive is to be installed above another drive or any other heat producing device the minimum vertical spacing is 150mm 5 inches above and below mount the drive vertically and do not restrict the air flow to the heat sink fins 6
- The optidrive must be installed in a pollution degree 1 or 2 environment the optidrive must be installed in a pollution degree 1 or 2 environment 6
- Www invertek co uk 6
- Gland sizes lock off 7
- Removing the terminal cover 7
- Grounding guidelines 8
- Grounding the drive 8
- Power wiring 8
- Wiring precautions 8
- Connection diagrams 9
- Ip66 nema 4x switched 9
- Ip66 nema 4x non switched 10
- Drive and motor connections 11
- Motor terminal box connections 11
- Control terminal connections 12
- Control wiring 12
- Managing the keypad 12
- Operation 12
- Rj45 data connection 12
- Changing parameters 13
- Keypad control 13
- Reset factory default settings 13
- Terminal control 13
- P 12 p 15 14
- Parameters to 14
- Set notes 14
- Switch position 14
- Using the rev 0 fwd selector switch switched version only 14
- Parameters 15
- Standard parameters 15
- Extended parameters 16
- P 00 read only drive status parameters 18
- Parameter group zero access and navigation 18
- Analog and digital input configurations 19
- Analog speed input with 1 preset speed 19
- Analog speed input with 2 preset speeds 4 preset speeds and max speed select 19
- And fwd rev switch 19
- Optidrive e2 ip66 nema 4x user guide 19
- Switch effectively giving 5 preset speeds 19
- Terminal mode p 12 0 19
- Typical applications 19
- Www invertek co uk 19
- 2 analog inputs 20
- Analog speed input with 1 preset speed 20
- And motor thermistor trip 20
- Deceleration ramp 20
- Example wiring 20
- Fwd rev 20
- Keypad mode p 12 1 or 2 20
- Local or remote analog speeds 20
- Optidrive e2 ip66 nema 4x user guide 20
- Push button fwd rev stop with fast stop 20
- Remote push button speed control with 20
- Www invertek co uk 20
- Example wiring 21
- Further information on configuring the pi controller for typical feedback applications please refer to the application note an ode 02 21
- Further information the modbus rtu register map information and communication setup please refer to the application note an ode 01 21
- Modbus control mode p12 3 or 4 21
- Optidrive e2 ip66 nema 4x user guide 21
- Remote closed loop pi feedback control 21
- Thermistor trip 21
- User pi control mode p 12 5 or 6 21
- With local analog speed input 21
- With local preset speed 1 21
- With local preset speed 1 and motor 21
- Www invertek co uk 21
- Environmental 22
- Fault messages 22
- Operational ambient temperature range 10 40 c frost and condensation free storage ambient temperature range 40 60 c maximum altitude 2000m derate above 1000m 1 100m maximum humidity 95 non condensing 22
- Optidrive e2 ip66 nema 4x user guide 22
- Technical data 22
- Troubleshooting 22
- Www invertek co uk 22
- 115v 10 1 phase input 3 phase 230v output voltage doubler 23
- 240v 10 1 phase input 3 phase output 23
- 240v 10 3 phase input 3 phase output 23
- 480v 10 3 phase input 3 phase output 23
- Maximum supply ratings for ul compliance 23
- Rating tables 23
Похожие устройства
- Invertek Drives ODP-2-22075-1KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-22150-1KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-22220-1KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-22075-3KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-22150-3KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-22220-3KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-32040-3KF42 Инструкция по эксплуатации
- Invertek Drives ODP-2-42055-3KF4N Инструкция по эксплуатации
- Invertek Drives ODP-2-42075-3KF4N Инструкция по эксплуатации
- Invertek Drives ODP-2-42110-3KF4N Инструкция по эксплуатации
- Invertek Drives ODP-2-52150-3KF4N Инструкция по эксплуатации
- Invertek Drives ODP-2-52185-3KF4N Инструкция по эксплуатации
- Invertek Drives ODP-2-62022-3KF*N Инструкция по эксплуатации
- Invertek Drives ODP-2-62030-3KF*N Инструкция по эксплуатации
- Invertek Drives ODP-2-62037-3KF*N Инструкция по эксплуатации
- Invertek Drives ODP-2-62045-3KF*N Инструкция по эксплуатации
- Invertek Drives ODP-2-72055-3KF*N Инструкция по эксплуатации
- Invertek Drives ODP-2-72075-3KF*N Инструкция по эксплуатации
- Invertek Drives ODP-2-72090-3KF*N Инструкция по эксплуатации
- Invertek Drives ODP-2-24075-3KF42 Инструкция по эксплуатации