Qtech QSW-8200-52T-AC — руководство пользователя: Протокол IPv6 Multicast и команды [23/39]
Превью страниц
Страница 23 /
39
![Qtech QSW-8200-52T-AC-DC [23/39] Commands for ipv6 dcscm](/views2/1596644/page23/bg17.png)
User Manual
Chapter 2. IPv6 Multicast Protocol 23
www.qtech.ru
Chapter 2 IPV6 MULTICAST PROTOCOL
2.1 Commands for IPv6 DCSCM
2.1.1 ipv6 access-list(ipv6 multicast source control)
Command: ipv6 access-list <8000-8099> {deny|permit} {{<source/M> }|{host-source
<source-host-ip>}|any-source} {{<destination/M> }|{host-destination <destination-
host-ip>}|any-destination}
no ipv6 access-list <8000-8099> {deny|permit} {{<source/M>}|{host-
source <source-host-ip>}|any-source} {{<destination/M> }|{host-
destination <destination-host-ip>}|any-destination}
Function: Configure IPv6 source control multicast access list, the no operation of this
command is used to delete the access list.
Parameters: <8000-8099>: The source control access list number.
{deny|permit}: Deny or permit.
<source/M>: The multicast source address and the length of mask.
<source-host-ip>: The multicast host address.
<destination/M>: The multicast destination address and the length of
mask.
<destination-host-ip>: The multicast destination host addresses.
Default: None.
Command Mode: Global Configuration Mode.
Usage Guide: IPv6 multicast source control entries control the ACL it uses with ACL
number 8000-8099, this command is used to configure such ACL. IPv6 multicast source
control ACL only needs to configure the source IPv6 address and destination IPv6
address (that is the group IPv6 addresses)which are to be controlled, the configuration
adopts a method similar to other ACLs, which can either be an address range
configured by the length of mask, or a specified host address or all addresses. Pay
attention to that: for group IPv6 addresses, the “all addresses” mentioned here is ff:/8.
Example:
Switch(config)#ipv6 access-list 8000 permit fe80::203:228a/64 ff1e::1/64
2.1.2 ipv6 access-list(multicast destination control)
Command: ipv6 access-list <9000-10999> {deny|permit} {{<source/M> }|{host-source
<source-host-ip>}|any-source} {{<destination/M> }|{host-destination <destination-
host-ip>}|any-destination}
no ipv6 access-list <9000-10999> {deny|permit} {{<source/M>
}|{host-source <source-host-ip>}|any-source}
{{<destination/M> }|{host-destination <destination-host-
ip>}|any-destination}
Содержание
- Content p.2
- Commands for igmp snooping 12 p.2
- Commands for dcscm 5 p.2
- Chapter 1 ipv4 multicast protocol 5 p.2
- Commands for mld snooping configuration 29 p.3
- Commands for ipv6 dcscm 23 p.3
- Chapter 2 ipv6 multicast protocol 23 p.3
- Commands for dcscm p.5
- Chapter 1 ipv4 multicast protocol p.5
- Command mode admin mode default igmp snooping debugging switch is disabled on the switch by default usage guide the command is used for enable the igmp snooping debugging switch of p.12
- Command ip igmp snooping p.12
- Command debug igmp snooping all packet event timer mfc no debug igmp snooping all packet event timer mfc function enable the igmp snooping switch of the switch the no debug igmp p.12
- Clear ip igmp snooping vlan p.12
- The switch switch igmp data packet message can be shown with packet parameter event message with event timer message with time downsending hardware entries message with mfc and all debugging messages with all p.12
- Switch clear ip igmp snooping vlan 1 mrouter port p.12
- Snooping all packet event timer mfc disables the debugging switch p.12
- Mrouter port p.12
- Ip igmp snooping p.12
- Debug igmp snooping all packet event timer mfc p.12
- Commands for igmp snooping p.12
- Commands for ipv6 dcscm p.23
- Chapter 2 ipv6 multicast protocol p.23
- Commands for mld snooping configuration p.29
- Multicast vlan association p.38
- Multicast vlan p.38
- Chapter 3 commands for multicast vlan p.38
- Switchport association multicast vlan p.39
- Multicast vlan association interface p.39
Похожие устройства
-
Qtech QSW-1500-20EF-POE-ACТехнические характеристики -
Qtech QSW-1500-19EF-POE-AC V3Описание параметров -
Qtech QSW-1500-10E-POE-DОписание параметров -
Qtech QSW-1500-6E-POE-DПодробное техническое описание -
Qtech QSW-4610Инструкция пользователя -
Qtech QSW-3750 REV. RИнструкция пользователя -
Qtech QSW-3750Руководство по эксплуатации -
Qtech QSW-3420Инструкция по применению -
Qtech QSW-9000-01Руководство по управлению -
Qtech QSW-9000-01Руководство по настройке -
Qtech QSW-9000-01Руководство по настройке управления -
Qtech QSW-9000-01Руководство по командам
Изучите команды для настройки управления мультикастом IPv6. Узнайте, как конфигурировать списки доступа для управления источниками и назначениями мультикаст-трафика.