Indesit KN1G27/RU [27/28] Care and maintenance

Indesit KNJ1G217/RU [27/28] Care and maintenance
27
GB
Care and maintenance
Switching the appliance off
Disconnect your appliance from the electricity supply
before carrying out any work on it.
Cleaning the appliance
! Do not use abrasive or corrosive detergents such as
stain removers, anti-rust products, powder detergents or
sponges with abrasive surfaces: these may scratch the
surface beyond repair.
! Never use steam cleaners or pressure cleaners on the
appliance.
It is usually sufficient simply to wash the hob using a
damp sponge and dry it with absorbent kitchen roll.
The stainless steel or enamel-coated external parts and
the rubber seals may be cleaned using a sponge that
has been soaked in lukewarm water and neutral soap.
Use specialised products for the removal of stubborn
stains. After cleaning, rinse well and dry thoroughly. Do
not use abrasive powders or corrosive substances.
The hob grids, burner caps, flame spreader rings
and the hob burners can be removed
to make cleaning easier; wash them in hot water and
non-abrasive detergent, making sure all burnt-on
residue is removed before drying them thoroughly.
For hobs with electronic ignition, the terminal part of the
electronic lighting devices should be cleaned
frequently and the gas outlet holes should be checked
for blockages.
The inside of the oven should ideally be cleaned after
each use, while it is still lukewarm. Use hot water and
detergent, then rinse well and dry with a soft cloth. Do
not use abrasive products.
Clean the glass part of the oven door using a sponge
and a non-abrasive cleaning product, then dry
thoroughly with a soft cloth. Do not use rough abrasive
material or sharp metal scrapers as these could
scratch the surface and cause the glass to crack.
The accessories can be washed like everyday
crockery, and are even dishwasher safe.
Stainless steel can be marked by hard water that has
been left on the surface for a long time, or by
aggressive detergents containing phosphorus. After
cleaning, rinse well and dry thoroughly. Any remaining
drops of water should also be dried.
The cover
If the cooker is fitted with a
glass cover, this cover
should be cleaned using
lukewarm water. Do not use
abrasive products.
It is possible to remove the
cover in order to make
cleaning the area behind
the hob easier. Open the
cover fully and pull it
upwards (
see figure
).
! Do not close the cover when the burners are alight or
when they are still hot.
Inspecting the oven seals
Check the door seals around the oven periodically. If the
seals are damaged, please contact your nearest
Authorised After-sales Service Centre. We recommend
that the oven is not used until the seals have been
replaced.
Gas tap maintenance
Over time, the taps may become jammed or difficult to
turn. If this occurs, the tap must be replaced.
!
This procedure must be performed by a qualifiedThis procedure must be performed by a qualified
This procedure must be performed by a qualifiedThis procedure must be performed by a qualified
This procedure must be performed by a qualified
technician who has been authorised by thetechnician who has been authorised by the
technician who has been authorised by thetechnician who has been authorised by the
technician who has been authorised by the
manufacturer.manufacturer.
manufacturer.manufacturer.
manufacturer.
Replacing the oven light bulb
1. After disconnecting the oven
from the electricity mains, remove
the glass lid covering the lamp
socket (
see figure
).
2. Remove the light bulb and
replace it with a similar one:
voltage 230 V, wattage 25 W, cap
E 14.
3. Replace the lid and reconnect the oven to the electricity
supply.
Assistance
Please have the following information handy:
The appliance model (Mod.).
The serial number (S/N).
This information can be found on the data plate located on
the appliance and/or on the packaging.

Содержание

Похожие устройства

Care and maintenance Switching the appliance off Q inoesiT The cover If the cooker is fitted with a glass cover this cover Disconnect your appliance from the electricity supply before carrying out any work on it should be cleared using lukewarm water Do not use abrasive products It is possible to remove the cover in order to make cleaning the area behind the hob easier Open the Cleaning the appliance Do not use abrasive or corrosive detergents such as stain removers anti rust products powder detergents or sponges with abrasive surfaces these may scratch the surface beyond repair Never use steam cleaners or pressure cleaners on the appliance It is usually sufficient simply to wash the hob using a damp sponge and dry it with absorbent kitchen roll The stainless steel or enamel coated external parts and the rubber seals may be cleaned using a sponge that has been soaked in lukewarm water and neutral soap Use specialised products for the removal of stubborn stains After cleaning rinse well and dry thoroughly Do not use abrasive powders or corrosive substances The hob grids burner caps flame spreader rings and the hob burners can be removed to make cleaning easier wash them in hot water and non abrasive detergent making sure all burnt on residue is removed before drying them thoroughly For hobs with electronic Ignition the terminal part of the electronic lighting devices should be cleaned frequently and the gas outlet holes should be checked for blockages cover fully and pull it upwards see figure Do not close the cover when the burners are alight or when they are still hot Inspecting the oven seals Check the door seals around the oven periodically If the seals are damaged please contact your nearest Authorised After sales Service Centre We recommend that the oven Is not used until the seals have been replaced Gas tap maintenance Over time the taps may become jammed or difficult to turn If this occurs the tap must be replaced This procedure must be performed by a qualified technician who has been authorised by the manufacturer Replacing the oven light bulb The Inside of the oven should Ideally be cleaned after each use while it is still lukewarm Use hot water and detergent then rinse well and dry with a soft cloth Do not use abrasive products 1 After disconnecting the oven from the electricity mains remove the glass lid covering the lamp socket see figure 2 Remove the light bulb and replace it with a similar one voltage 230 V wattage 25 W cap E 14 Clean the glass part of the oven door using a sponge and a non abrasive cleaning product then dry thoroughly with a soft cloth Do not use rough abrasive material or sharp metal scrapers as these could scratch the surface and cause the glass to crack The accessories can be washed like everyday crockery and are even dishwasher safe 3 Replace the lid and reconnect the oven to the electricity supply Assistance Please have the following information handy Stainless steel can be marked by hard water that has been left on the surface for a long time or by aggressive detergents containing phosphorus After cleaning rinse well and dry thoroughly Any remaining drops of water should also be dried The appliance model Mod The serial number S N This Information can be found on the data plate located on the appliance and or on the packaging

Скачать