Indesit KNJ1G27/RU [18/28] Adapting to different types of gas
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Indesit KNJ1G27/RU [18/28] Adapting to different types of gas

Indesit KNJ1G217/RU [18/28] Adapting to different types of gas
18
GB
A
V
! If one or more of these conditions is not fulfilled or
if the cooker must be installed according to the
conditions listed for class 2 - subclass 1 appliances
(installed between two cupboards), the flexible steel
hose must be used instead (
see below
).
Connecting a flexible jointless stainless steel pipe
to a threaded attachment
Make sure that the hose and gaskets comply with
current national legislation.
To begin using the hose, remove the hose holder on the
appliance (the gas supply inlet on the appliance is a
cylindrical threaded 1/2 gas male attachment).
! Perform the connection in such a way that the hose
length does not exceed a maximum of 2 metres,
making sure that the hose is not compressed and
does not come into contact with moving parts.
Checking the connection for leaks
When the installation process is complete, check
the hose fittings for leaks using a soapy solution.
Never use a flame.
Adapting to different types of gas
It is possible to adapt the appliance to a type of gas
other than the default type (this is indicated on the
rating label on the cover).
Adapting the hob
Replacing the nozzles for the hob burners:
1. Remove the hob grids and slide the burners off
their seats.
2. Unscrew the nozzles using a
7 mm socket spanner (
see
figure
), and replace them with
nozzles suited to the new type
of gas(
see Burner and nozzle
specifications table
).
3. Replace all the components
by following the above
instructions in reverse.
Adjusting the hob burners’ minimum setting:
1. Turn the tap to the minimum position.
2. Remove the knob and adjust the regulatory
screw, which is positioned inside or next to the tap
pin, until the flame is small but steady.
! If the appliance is connected to a liquid gas
supply, the regulatory screw must be fastened as
tightly as possible.
3. While the burner is alight, quickly change the position
of the knob from minimum to maximum and vice versa
several times, checking that the flame is not
extinguished.
! The hob burners do not require primary air adjustment.
Adapting the oven
Replacing the oven burner nozzle:
1. Remove the oven compartment.
2. Slide out the protection
panel A
(
see diagram
).
3. Remove the oven burner
after unscrewing the screws V
(
see figure
).
The whole operation will be
made easier if the oven door
is removed.
4. Unscrew the nozzle using a
special nozzle socket spanner
(
see figure
) or with a 7 mm
socket spanner, and replace it
with a new nozzle that is
suited to the new type of gas
(
see Burner and nozzle
specifications table
).
Adjusting the gas oven burner’s minimum setting:
1. Light the burner (
see Start-up and Use
).
2. Turn the knob to the minimum position (MIN) after
it has been in the maximum position (MAX) for
approximately 10 minutes.
3. Remove the knob.
4. Tighten or loosen the adjustment screws on the
outside of the thermostat pin (
see figure
) until the
flame is small but steady.
! If the appliance is connected to liquid gas, the
adjustment screw must be fastened as tightly as
possible.

Содержание

Похожие устройства

GB If one or more of these conditions is not fulfilled or if the cooker must be installed according to the conditions listed for class 2 subclass 1 appliances installed between two cupboards the flexible steel hose must be used instead see below 3 While the burner is alight quickly change the position of the knob from minimum to maximum and vice versa several times checking that the flame is not extinguished The hob burners do not require primary air adjustment Connecting a flexible jointless stainless steel pipe to a threaded attachment Adapting the oven Make sure that the hose and gaskets comply with current national legislation To begin using the hose remove the hose holder on the appliance the gas supply inlet on the appliance is a cylindrical threaded 1 2 gas male attachment Replacing the oven burner nozzle 1 Remove the oven compartment 2 Slide out the protection panel A see diagram Perform the connection in such a way that the hose length does not exceed a maximum of 2 metres making sure that the hose is not compressed and does not come into contact with moving parts Checking the connection for leaks When the installation process is complete check the hose fittings for leaks using a soapy solution Never use a flame 3 Remove the oven burner after unscrewing the screws V see figure The whole operation will be made easier if the oven door is removed Adapting to different types of gas It is possible to adapt the appliance to a type of gas other than the default type this is indicated on the rating label on the cover Adapting the hob Replacing the nozzles for the hob burners 1 Remove the hob grids and slide the burners off their seats 2 Unscrew the nozzles using a 7 mm socket spanner see figure and replace them with nozzles suited to the new type of gas see Burner and nozzle specifications table 3 Replace all the components by following the above instructions in reverse Adjusting the hob burners minimum setting 1 Turn the tap to the minimum position 2 Remove the knob and adjust the regulatory screw which is positioned inside or next to the tap pin until the flame is small but steady If the appliance is connected to a liquid gas supply the regulatory screw must be fastened as tightly as possible 18 4 Unscrew the nozzle using a special nozzle socket spanner see figure or with a 7 mm socket spanner and replace it with a new nozzle that is suited to the new type of gas see Burner and nozzle specifications table Adjusting the gas oven burner s minimum setting 1 Light the burner see Start up and Use 2 Turn the knob to the minimum position MIN after it has been in the maximum position MAX for approximately 10 minutes 3 Remove the knob 4 Tighten or loosen the adjustment screws on the outside of the thermostat pin see figure until the flame is small but steady If the appliance is connected to liquid gas the adjustment screw must be fastened as tightly as possible

Скачать