Home
Главная
Makita
УШМ (болгарка)
DGA452Z аккумуляторная
Инструкция по эксплуатации Страница: 8

Makita DGA452Z аккумуляторная [8/32] Accessories

OPERATION

WARNING:

• It should never be necessary to force the tool. The

weight of the tool applies adequate pressure. Forcing

and excessive pressure could cause dangerous wheel

breakage.

• ALWAYS replace wheel if tool is dropped while grind-

ing.

• NEVER bang or hit grinding disc or wheel onto work.

• Avoid bouncing and snagging the wheel, especially

when working corners, sharp edges etc. This can

cause loss of control and kickback.

• NEVER use tool with wood cutting blades and other

sawblades. Such blades when used on a grinder fre-

quently kick and cause loss of control leading to per-

sonal injury.

CAUTION:

• Make the depth of a single cut up to 5 mm. Adjust pres-

sure on the tool so that the tool does not slow down

during the operation.

• After operation, always switch off the tool and wait until

the wheel has come to a complete stop before putting

the tool down.

• If the tool is operated continuously until the battery car-

tridge has discharged, allow the tool to rest for 15 min-

utes before proceeding with a fresh battery.

Grinding and sanding operation (Fig. 10)

ALWAYS hold the tool firmly with one hand on housing

and the other on the side handle. Turn the tool on and

then apply the wheel or disc to the workpiece.

In general, keep the edge of the wheel or disc at an angle

of about 15 degrees

to the workpiece surface.

During the break-in period with a new wheel, do not work

the grinder in the B direction or it will cut into the work-

piece. Once the edge of the wheel has been rounded off

by use, the wheel may be worked in both A and B direc-

tion.

Operation with diamond wheel (acces-

sory)

WARNING:

• Forcing and exerting excessive pressure or allowing

the wheel to bend, pinch or twist in the cut can cause

overheating of the motor and dangerous kickback of

the tool.

CAUTION:

• After cutting operation, make sure that the diamond

wheel stops revolving completely. Then, place the tool.

It is dangerous to place the tool before turning off the

tool. If there are dust or dirt around the tool, the tool

may suck in them.

Be sure that the wheel does not contact the workpiece.

Turn the tool on and hold the tool firmly. Wait until the

wheel attains full speed. Now simply move the tool for-

ward over the workpiece surface, keeping it flat and

advancing smoothly until the cutting is completed.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before attempting to perform

inspection or maintenance.

The tool and its air vents have to be kept clean. Regularly

clean the tool's air vents or whenever the vents start to

become obstructed. (Fig. 11)

Replacing carbon brushes

Remove and check the carbon brushes regularly. Replace

when they wear down to the limit mark. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes. (Fig. 12)

Insert the top end of slotted bit screwdriver into the notch

in the tool and remove the holder cap cover by lifting it up.

(Fig. 13)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps. (Fig. 14)

Reinstall the holder cap cover on the tool.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Wheel guard (Wheel cover)

• Inner flange

• 115 mm Depressed center wheels

• Lock nut (For depressed center wheel)

• Rubber pad

• Abrasive discs

• Lock nut (For abrasive disc)

• Lock nut wrench

• Wire cup brush

• Wire bevel brush 85

• Side grip

• Dust collecting wheel guard

• 115 mm Diamond wheel

• Various type of Makita genuine batteries and chargers

Содержание

Похожие устройства

OPERATION MAINTENANCE WARNING It should never be necessary to force the tool The weight of the tool applies adequate pressure Forcing and excessive pressure could cause dangerous wheel breakage ALWAYS replace wheel if tool is dropped while grind ing NEVER bang or hit grinding disc or wheel onto work Avoid bouncing and snagging the wheel especially when working corners sharp edges etc This can cause loss of control and kickback NEVER use tool with wood cutting blades and other sawblades Such blades when used on a grinder fre quently kick and cause loss of control leading to per sonal injury CAUTION Always be sure that the tool is switched off and the bat tery cartridge is removed before attempting to perform inspection or maintenance CAUTION Make the depth of a single cut up to 5 mm Adjust pres sure on the tool so that the tool does not slow down during the operation After operation always switch off the tool and wait until the wheel has come to a complete stop before putting the tool down If the tool is operated continuously until the battery car tridge has discharged allow the tool to rest for 15 min utes before proceeding with a fresh battery Grinding and sanding operation Fig 10 ALWAYS hold the tool firmly with one hand on housing and the other on the side handle Turn the tool on and then apply the wheel or disc to the workpiece In general keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface During the break in period with a new wheel do not work the grinder in the B direction or it will cut into the work piece Once the edge of the wheel has been rounded off by use the wheel may be worked in both A and B direc tion Operation with diamond wheel acces sory WARNING Forcing and exerting excessive pressure or allowing the wheel to bend pinch or twist in the cut can cause overheating of the motor and dangerous kickback of the tool CAUTION After cutting operation make sure that the diamond wheel stops revolving completely Then place the tool It is dangerous to place the tool before turning off the tool If there are dust or dirt around the tool the tool may suck in them Be sure that the wheel does not contact the workpiece Turn the tool on and hold the tool firmly Wait until the wheel attains full speed Now simply move the tool for ward over the workpiece surface keeping it flat and advancing smoothly until the cutting is completed 8 The tool and its airvents have to be kept clean Regularly clean the tool s air vents or whenever the vents start to become obstructed Fig 11 Replacing carbon brushes Remove and check the carbon brushes regularly Replace when they wear down to the limit mark Keep the carbon brushes clean and free to slip in the holders Both carbon brushes should be replaced at the same time Use only identical carbon brushes Ag 12 Insert the top end of slotted bit screwdriver into the notch in the tool and remove the holder cap cover by lifting it up Ag 13 Use a screwdriver to remove the brush holder caps Take out the worn carbon brushes insert the new ones and secure the brush holder caps Fig 14 Reinstall the holder cap cover on the tool To maintain product SAFETY and RELIABILITY repairs any other maintenance or adjustment should be per formed by Makita Authorized Service Centers always using Makita replacement parts ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons Only use accessory or attachment for its stated purpose If you need any assistance for more details regarding these accessories ask your local Makita Service Center Wheel guard Wheel cover Inner flange 115 mm Depressed center wheels Lock nut For depressed center wheel Rubber pad Abrasive discs Lock nut For abrasive disc Lock nut wrench Wire cup brush Wire bevel brush 85 Side grip Dust collecting wheel guard 115 mm Diamond wheel Various type of Makita genuine batteries and chargers

Скачать