Gespasa IRON-50 24 VDC (00011) [4/4] Iron 50 12 or 24 vdc
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Gespasa IRON-50 24 VDC (00011) [4/4] Iron 50 12 or 24 vdc

Gespasa IRON-50 24 VDC (00011) [4/4] Iron 50 12 or 24 vdc
10. EU CONFORMITY DECLARATION
8. PROBLEM GUIDE
9. WARRANTY
1. All the products manufactured by TOT COMERCIAL SA have a WARRANTY of 12 (twelve) months or 500,000 litres from their purchase, against any manufacturing
defect.
2. TOT COMERCIAL SA guarantees, in the warranty period, the change, the devolution of the defective part or product. This material must be sent with prepaid
freight to our factory or any appointed technical service. After our technical inspection, it will be determined whether the responsibility is from the manufacturer,
the user, the installer or the transport.
3. The warranty does not cover: the inadequate use, the negligence, the abuse, the corrosion, the manipulation or the wrong installation of the products, the use
of non-original spare parts or not corresponding to the specifi c model. All the manufactured and/or commercialized equipment must be installed according to the
manufacturer's instructions.
4. The accessories and the products not manufactured by TOT COMERCIAL SA are liable for their original manufacturer's warranty.
5. Because of the constant innovations and development, TOT COMERCIAL SA reserves the right to modify the specifi cations of its products and publicity, without
prior notifi cation.
BREAKDOWN POSSIBLE CAUSE SOLUTION
The tank is full. The pump is
working, but the liquid does not go
out through the automatic nozzle.
- There is an air chamber in the delivery line,
and the automatic nozzle cannot be opened.
- Remove the automatic nozzle. Start the pump until it is primed, and the liquid is automatically
going out. Then install again the automatic nozzle.
The pump is working, but no fl uid
comes out.
- problem in the suction line
- The bypass valve is opened
- retainer leak
- blocked outlet tube, nozzle or fi lter
- motor breakdown. The rotor must turn
anticlockwise, looking at the pump from its
heading; if not, return it for repairing.
- blade friction
- Check whether there are leaks in the suction line.
- Remove and check the valve.
- Tighten the cover or change the retainer.
- Check whether the outlet tube of the pump, the hose, the nozzle and the fi lter are blocked.
- Check the connection polarity.
- Check whether the blades and the grooves are worn out.
The pump makes noise, but it does
not work.
- dirt inside the pump, blade friction
- motor breakdown
- Clean the pump interior.
- Return it for repairing.
Low fl ow rate - fi lthy fi lter
- problem in the suction or delivery line
- dirt in the red adapter
- Disassemble and clean the fi lter.
- Check whether the suction line has some leak or restriction; maybe it is too narrow, long or no
hermetic.
- Clean the inner sieve.
The pump runs slowly making
strange noise.
- wrong voltage
- motor breakdown
- Check the inlet voltage.
- Return it for repairing.
The motor is stopped or burns. - low voltage
- solid impurities in the pump inner
- Check the inlet voltage.
- Disassemble and clean the pump.
The motor heats up excessively. - high viscosity fl uid pumping
- blocked fi lter
- narrow suction or delivery tube
- motor breakdown
- These fl uids only can be pumped during a short period.
- Remove and clean the fi lter
- Replace it with an adequate tube
- Return it for repairing.
The motor does not start. - There is no supply system.
- motor breakdown
- not lined up / connected switch connection
- Check the battery state.
- Return it for repairing.
- Fit the switch connection / Connect it.
Liquid leak - connection joint in bad state
- mechanical seal in bad state
- Check all the connection joints.
- Replace the mechanical seal.
Manufacturer: TOT COMERCIAL SA - Partida Horta d'Amunt s/n - Apartado Correos nº 149 - 25600 BALAGUER (Lleida) SPAIN
STATES under its own responsibility the supplied product:
SELF-SUCTION FUEL PUMP · Make: GESPASA
Model:
IRON-50 12 or 24 VDC
is in accordance with the following legislative and/or normative documents
DIRECTIVES Nr. and issued rules date
2006/42/UE: Safety of machinery EN 809:1999+A1:2010/AC:2010
EN-ISO 12100:2012
- This Declaration will lose its validity in case that any modifi cation is made without the explicit manufacturer's consent.
Balaguer, November 2017
Andreu Pané

Содержание

Похожие устройства

Скачать