Nilfisk SC DELTA 6P 160/4500-3 EU [12/17] C maintenance
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Nilfisk SC DELTA 6P 160/4500-3 EU [12/17] C maintenance

Nilfisk SC DELTA 6P 160/4500-3 EU [12/17] C maintenance
12 Original Instructions
EN
SC DELTA
B.3 Operation - automatic start/stop
Always hold the spray lance with both hands!
The machine is automatically activated when the trigger (1)
of the spray handle is activated.
When the trigger is released, the machine automatically
stops after 20 seconds.
When the machine is not in use, the trigger should be locked
with locking device (2).
B.4 Stop
Danger of scalding!
Never detach high pressure hoses at a water temperature
above 50°C.
Never detach the high pressure hose while the machine is
in operation.
1. To stop the machine, push the red stop button (#4) and
turn the main switch (2) to position - 0 -.
B.5 Frost protection
The machine should be installed in a frost-free room. This
applies to pump as well as pipelines incl. of outlet points.
Concerning outdoor outlet points it should be possible to
empty that part of the line which is exposed to frost.
IMPORTANT: For safety reasons, hoses, spray lances and
other accessories should always be thawed prior to use.
C - Maintenance
It applies to the most exposed components that a minimum of maintenance ensures a prolonged and prob lem-free ope-
ration. Therefore it will be a good idea to make a habit of the following:
Maintenance Schedule
Weekly
After the fi rst 50
operating hours
Every six months
or 500 operating
hours
As required
Checking pump oil level
Changing pump oil
Cleaning water fi lter

Prior to attaching the water hose and the high pressure
hose, the quick couplings should be cleaned of dust and
sand.
Prior to attaching the spray lance or other accessories to
the spray handle, the machine should be started and the
quick coupling cleaned of dust and sand.
C.1 Oil
Check the oil level in the oil glas.
If the oil level gets too low, the pump will automatically
shut down and #6 will light up.
In the case of repeated low oil level (oil waste) please
contact a Nilfi sk service technician.
PROTECT THE ENVIRONMENT
Waste oil and oil sludge must be removed as laid down
in the instructions.
C.2 Water fi lter
To avoid debris entering the high pressure pump, a water
fi lter (fi ne) is fi tted at the wa ter inlet. Dependent on the
purity of the water, this fi l ter will have to be cleaned at
regular in ter vals.
The fi lter can be removed when the plug (pos. 1) has
been un screwed.
There is also a fi lter in the tank (pos. 11). This fi lter can
be removed by dismounting the two screws (torx 20).
Pull the fi lter up and out of the water tank. Clean the fi lter
and remount it.
C.3 Cleaning of high pressure nozzle
A clogging up in the nozzle causes bad cleaning, and a
cleaning of the nozzle is immediately required.
1. Stop the machine and detach the spray lance.
2. Clean the nozzle.
IMPORTANT: ONLY use the cleaning tool when the spray
lance is detached.
3. Flush the spray lance backwards with water.
4. If the pressure is still too high, repeat items 1-3.
C.4 Disposable waste
This high pressure washer consists of parts which can aff ect
the environment when thrown away. Parts that can pollute
are as follows:
Oil, painted/zinc-coated parts, plastics/plastic-coated parts.
Therefore, it is important to follow the laws concerning the
removal of polluting and dangerous materials when replacing
spare parts or disposing of high pressure washer.
It is recommended that you bring the rejected parts to waste
disposal areas or recycling plants that are approved for the
destruction of these types of materials.

Содержание

Похожие устройства

Скачать