Home
Главная
Vitek
Утюг
VT-8340
Инструкция по эксплуатации Страница: 4

Vitek VT-8340 [4/28] English

ENGLISH

Attention! Do not allow children to play with

polyethylene bags or packaging film. Danger

of suffocation!

• This unit is not intended for usage by children.

Place the unit out of reach of children during

operation and cooling down.

• The unit is not intended for usage by physi-

cally or mentally disabled persons (including

children) or by persons lacking experience or

knowledge if they are not under supervision of

a person who is responsible for their safety or

if they are not instructed by this person on the

usage of the unit.

• Do not use the unit if the power plug or the

power cord is damaged. If the power cord is

damaged, it should be replaced by the manu-

facturer, maintenance service or similar quali-

fied personnel to avoid danger.

• Do not attempt to repair the unit. Do not disas-

semble the unit by yourself, if any malfunction is

detected or after it was dropped, unplug the unit

and apply to any authorized service center from

the contact address list given in the warranty

certificate and on the website www.vitek.ru.

• Transport the unit in the original package only.

• Keep the unit out of reach of children and dis-

abled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE

ONLY, ITS COMMERCIAL USAGE AND USAGE

IN PRODUCTION AREAS AND WORK SPACES IS

PROHIBITED.

BEFORE THE FIRST USE

After unit transportation or storage at low

temperature keep it for at least three hours

at room temperature before switching on.

• Unpack the iron; remove the protection from

the soleplate (13), if any.

• Check the unit for damages, do not use the

iron in case of damages.

• Before switching the iron on, make sure that

your home mains voltage corresponds to the

iron operating voltage.

• The unit is intended for operation with AC

system and 50 Hz or 60 Hz frequency, the

unit does not need any additional settings

for operating with the required nominal fre-

quency.

• There may be water residue in the tank, this

is normal, as the iron has undergone factory

quality control.

Note: While the first switching on the heating

element of the iron burns, therefore occurrence

of foreign smell and a small amount of smoke is

possible, it is normal.

WATER SELECTION

You can use tap water to fill the water tank (10).

If tap water is hard, use distilled or demin-

eralized water, this will prolong service life

of the iron.

Note: Do not fill the water tank (10) with scented

liquids, vinegar, starch solution, descaling

reagents, chemical agents etc.

FILLING THE WATER TANK

Before filling the iron with water, make sure that

it is unplugged.

• Set the continuous steam supply knob (3) to

the position

– steam supply is off.

• Open the lid (2) and pour water into the water

tank (10) using the beaker (14) and then close

the lid (2) tight.

Note:

• Do not pour water over the «MAX» mark (12).

• If you need to refill water during ironing,

always switch the iron off first and unplug it.

• After you finish ironing, switch the iron off,

wait until it cools down completely, then open

the water inlet lid (2), turn over the iron and

pour out the remaining water.

IRONING TEMPERATURE

Instead of the habitual temperature control knob,

this iron model uses the Smart Sense technology

determining the optimal combination of temper-

ature and the required amount of steam for any

fabric allowing ironing.

Before operation, test the heated iron on a piece

of cloth to be sure that the iron soleplate (13) and

the water tank (10) are clean.

• If the item label is marked with the symbol ,

do not iron the item.

• Corduroy and other fabrics that become

glossy quickly should be ironed strictly in

one direction (in the direction of the pile) with

slight pressure.

• To avoid appearance of glossy spots on syn-

thetic and silk fabrics, iron them backside.

IM VT-8340.indd 4 16.01.2019 17:27:55

Vitek VT-8340 [4/28] English

Содержание

Похожие устройства