Home
Главная
Vitek
Увлажнители Воздуха
VT-2346
Инструкция по эксплуатации Страница: 5

Vitek VT-2346 [5/32] English

ENGLISH

– When the set time is reached the unit will be

switched off.

– To switch the timer off, press the button (15)

until the light indicators (16) go out.

Night illumination

The night illumination switches on automatically

when you switch the unit on, it is available in the

operating modes with low, medium and high mist

release intensity.

In normal operating mode the illumination colors

change by rotation.

Not enough water

– When the water tank (2) and the process cham-

ber (8) become empty, the unit will switch off.

The illumination will light up red.

– Unplug the unit and remove the water tank (2).

Fill the tank (2) with water (see chapter «Using

the air humidifier»). Install the water tank (2)

filled with water on the humidifier body (9).

– Switch the unit on for further operation.

CLEANING AND CARE

WARNING!

Always switch the air humidifier off before clean-

ing, disconnect the power adapter (13) from the

mains and remove the adapter cord connector from

the socket (11). Hard water causes appearance of

mineral deposits (scale) in the process chamber

(8) and in the water tank (2) that leads to improper

operation of the unit. To avoid it:

– use filtered and settled water. If tap water is

hard, it is recommended to mix tap water with

distilled water in proportion 1:1. If tap water is

too hard, mix it with distilled water in proportion

1:2 or use distilled water only.

– Change water in the water tank (2) twice a week.

– Thoroughly wash the process chamber (8) and

the water tank (2) with neutral detergent solu-

tion twice a week.

– To clean the «sprayer» from the mineral deposit

(scale) (7) add 5-10 drops of detergent on it and

wait for approximately 10-15 minutes.

– Remove the scale from the sprayer surface with

a soft brush, and then wash the process cham-

ber (8) with a neutral detergent solution.

– Rinse the process chamber (8) several times.

Wipe the process chamber (8) with a soft cloth.

– Clean the air humidifier body (9) with a soft,

slightly damp cloth, and then wipe it dry.

– Clean the air inlet (4) and the air inlet grid (11)

on the unit body (9) bottom as it becomes

dirty.

– To clean the float (5) remove it; to do this lift it

up and remove the left axis of the float from the

holder (6) groove, then remove the right axis.

Clean the float (5) from mineral scale.

– Install the float (5) back to its place. To do it,

first insert the right axis of the float (5) into the

holder (6) opening and then insert the left axis

of the float (5) into the holder (6) groove. Make

sure that the float (5) axial movement (rotation)

is not hindered.

Notes:

– do not immerse the air humidifier body into

water or other liquids;

– do not use abrasives or solvents for cleaning the

sprayer (7);

– you can use a descaling agent for kettles as a

detergent for the sprayer (7) and the float (5),

strictly following the instruction for this sub-

stance.

STORAGE

– Pour the water out of the tank and make sure

that the process chamber and the sprayer are

dry before taking the unit away for storage.

– Do not keep water inside the tank (2) or the pro-

cess chamber (8) of the unit.

– Keep the air humidifier in a dry cool place away

from children and disabled persons.

TROUBLESHOOTING

Problem Possible causes Troubleshooting

No “mist” The unit is connected

improperly

Check if the power plug is inserted into the mains socket.

The unit is off Switch the unit on by pressing the button (13).

Water tank is empty

or there isn’t enough

water in the tank

Fill the water tank (2) with enough water.

IM VT-2346.indd 5 8/17/20 8:28 AM

Vitek VT-2346 [5/32] English

Содержание

Похожие устройства