Grillo FD 1500 PRO 4WD [10/83] Putting the machine into service
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Grillo FD 1500 PRO 4WD [10/83] Putting the machine into service

Translation of the original instructions
7
4 cylinders, liquid cooling system with hydraulic fan, equipped with automatic radiator cleaning device.
FUEL TANK: 40 litres.
HYDAULIC OIL TANK: 36 litres.
HOURLY CONSUMTION: 7,5 litres approximately.
STARTER: electric 12V.
TRACTION: hydraulic, 4 wheel drive (permanent with anti skid).
PUSH BUTTON DIFF-LOCK.
GEARBOX: hydrostatic transmission with 4 hydraulic engines on the 4 wheels.
STEERING SYSTEM: hydraulic drive with steering wheel.
CLUTCH: hydraulic, electrically activated for PTO, with blade brake.
SPEED: 0-20 km/h: continuous variation.
WHEELS: front 24 x 12.00-12; rear 20 x 10.00-10.
MOTORISED BAFFLE PROVIDES FULL AND EVEN GRASS CATCHER FILLING.
GRASS CATCHER: 900 litres.
DISCHARGE HEIGHT: 2100 mm, REAR PROJECTION: 500 mm.
LOADING ACCELERATOR: diameter 400 mm with hydraulic engine with safety valve against accidental impacts,
independent activation.
AUTOMATIC FEATURES: automatically disengaging blade and loading accelerator when the grass catcher is full.
BRAKE: hydraulic service and parking brake.
HYDRAULIC DECK LIFTING AND BASKET EMPTYING.
CUTTING HEIGHT: adjustable to 25-35-50-60-75-85-95-110 mm.
SEAT: super comfort, adjustable and sprung seat with arm-rests.
STEERING WHEEL: steering column, with height and tilt adjustment.
STEERING RADIUS: 625 mm.
HOURLY MOWING CAPACITY: 15,500 m
2
/h approx.
ACCESSORIES: 155 cm cutting deck with collection and anti-shock discs, weight 180 kg. LMP cutting deck, 160
cm cutting width, side and rear discharge, mulching, size with baffle 192 cm, weight 170 kg. Hydraulic kit for
accessories. Adjustable 165 cm snow blade with hydraulic control +/- 30°. 150 cm all-purpose flail with scarifying kit.
Cabin, air condition kit. Lights kit.
SIZE (with cutting deck): Length: 3420 mm, Width: 1620 mm, Height: 1790 mm.
SIZE (without cutting deck): Length: 2500 mm, Width: 1350 mm.
CLEAR SPAN FROM THE GROUND: 180 mm.
DISTANCE BETWEEN AXLES: 1260 mm.
WEIGHT (without cutting deck): 1245 kg.
PUTTING THE MACHINE INTO SERVICE
- Make sure the machine is complete and that it has not suffered any damage during transit.
- Check the levels of the engine oil (fig. 46) and hydrostatic transmission oil (fig. 4).
- Check the tyre pressure:
Front wheels 24 x 12.00 - 12 (1.6 bar)
Rear wheels 20 x 10.00 - 10 (1.6 bar)
Deck wheels (1.5 bar)
- Check the battery voltage, it must not be less than 12.5 Volts; recharge if necessary.
- If a dry battery has been supplied with separate acid, to put the machine into service proceed as follows:
1) pour in the acid and wait 2 hours;
2) charge the battery with a charger set to 12 Volts on a slow charge for 2 hours.
Caution, if this procedure is not observed this could lead to the battery deteriorating and the acid leaking out
during work.
BATTERY
Caution! The gases released by the battery are explosive, so keep it away from naked flames or sparks. Check the
level of the liquid at regular intervals and keep the terminals greased with Vaseline.
Important:
- Do not invert the battery poles.
- Do not run the lawnmower without the battery, as it is equipped with a charge regulator.
- Be careful not to cause any short circuits.
RUNNING IN - CAUTION!!
Change the engine oil and filter after the first 50 hours of work.
Check for oil leaks or loose screws, especially those that retain the blades and the wheels.
Adjust the tension on the PTO belts with the nut on the corresponding spring: the spring length has to be adjusted
at 92 mm (fig. 5, ref. A).

Содержание

Похожие устройства

Скачать