![Daikin EWLP026KBW1N [15/20] Implemented error code](/img/pdf.png)
Daikin EWLP026KBW1N [15/20] Implemented error code
![Daikin EWLP030KBW1N [15/20] Implemented error code](/views2/1656544/page15/bgf.png)
EWLP012~065KBW1N
Condenserless water-cooled water chillers
4PW61666-1A – 2012.04
Operation manual
14
Data representation of the Modbus protocol
■ Digital
All digital data is coded by a single bit:
■ "0" for OFF
■ "1" for ON.
All digital variables are assigned to bits of consecutive registers,
each one having:
■ the lower-address variable assigned to the less significant bit
■ the higher-address variable assigned to the most significant
bit.
■ Analogue and integer data
An analogue and integer value is represented by a 16-bit WORD
register in binary notation. For each register, the first byte
contains the high order bits and the second byte contains the
low order bits.
■ The analogue variables are represented in tenths:
for example, the value 10.0 is transmitted as 0064h=100d
for example, the value –10.0 is transmitted as FF9Ch=–100d
■ The integer variables are transferred using the effective
value:
for example, the value 100 is transmitted as 0064h=100d
The address card operates on registers where one register must
be considered at 16-bit.
In case the BMS or supervisory system tries to write a value of a
parameter that is out of range, the writing will be ignored.
Implemented error code
Defining the BMS setting
Activating the Modbus protocol
The Modbus protocol is activated by setting the h23 parameter to 1.
This is a user parameter, refer to "How to consult and modify the user
parameters" on page 11.
Defining the unit’s serial address
To define each unit’s unique serial address required for
communication with the supervisionary system, set parameter h10.
This is a user parameter, refer to "How to consult and modify the user
parameters" on page 11.
Variables database
The BMS or supervisory system and the chiller unit communicate
through a fixed set of variables, also called address numbers.
Hereafter, you will find the information you need about the digital,
integer and analogue variables that the BMS or supervisory system
can read from or write to the address card of the chiller.
For addresses of all the direct and user parameters refer to
"Overview of the direct and user parameters" on page 10.
Overview of all variables which are not direct or user
parameters
Code Modbus interpretation Condition
1 Illegal function Message is not supported or the
number of variables required is greater
than the allowed limit (length ≤20)
Description
Modbus
address
Parameter
type
(*)
(*) D=digital.
Circuit alarm
1=A1, HP1, or LP1
alarm codes active
0=no alarm code active
Read
only
41 D
General alarm
1=FL alarm code
0=no alarm code active
Read
only
45 D
NTC Probe alarm
1=E1, E2, or E3 alarm
codes
0=no alarm code active
Read
only
46 D
Input of flowswitch
alarm
1=closed
0=open
Read
only
53 D
Input of
changeable digital
S7S input
1=closed
0=open
Read
only
54 D
Input of high
pressure or
discharge protector
or overcurrent
alarm
1=closed
0=open
Read
only
55 D
Input of low
pressure switch
alarm
1=closed
0=open
Read
only
56 D
Input of
changeable digital
S9S input
1=closed
0=open
Read
only
57 D
Output of
compressor 1
1=on
0=off
Read
only
59 D
Output of
compressor 2
1=on
0=off
Read
only
60 D
Output of pump
1=on
0=off
Read
only
61 D
Output of reversing
valve
1=on
0=off
Read
only
62 D
Output of alarm
1=on
0=off
Read
only
63 D
On or off
1=on
0=off
Read/
write
64 D
Cooling or heating
1=cooling
0=heating
Read/
write
65 D
Содержание
- Condenserless water cooled water chillers 1
- Operation manual 1
- Introduction 2
- Ntroduction 2
- Operation manual 2
- Electrical specifications 3
- Electrical specification 3
- Technical specifications 3
- Technical specification 3
- 14 15 16 4
- Description 4
- Escription 4
- Figure main components 4
- The ewlp condenserless water cooled water chillers are available in 7 standard sizes 4
- Function of the main components 5
- Safety devices 5
- Internal wiring parts table 6
- Before operation 7
- Checks before initial start up 7
- Digital controller 7
- Efore operation 7
- General recommendations 7
- Operation 7
- Peration 7
- Power supply connection and crankcase heating 7
- User interface 7
- Water supply 7
- Adjusting the cooling temperature setpoint on page 8 8
- Consulting actual operational information on page 9 8
- Direct and user parameters 8
- Each parameter is defined by a code and a value for example the parameter used to select local or remote on off control has code h07 and value 1 or 0 8
- Example the leds f and g are displayed when accessing a parameter group or when accessing parameters directly 8
- For an overview of the parameters refer to overview of the direct and user parameters on page 10 8
- Function during main display not inside menu 8
- Keys provided on the controller 8
- Leds provided on the controller and remote interface 8
- Legibility of the numeric display may decrease in direct sunlight 8
- Resetting alarms on page 9 8
- Resetting warnings on page 9 8
- Switching the unit on on page 8 and switching the unit off on page 8 8
- Temperature readout tolerance 1 c 8
- The digital controller provides direct and user parameters the direct parameters are important for the everyday usage of the unit e g to adjust the temperature setpoint or to consult actual operational information the user parameters on the contrary provide advanced features such as adjusting time delays 8
- The function carried out when the user presses one or a combination of these keys depends on the status of the controller and the unit at that specific moment 8
- This chapter deals with the everyday usage of the ewlp units here you will learn how to perform routine tasks such as 8
- When selecting a parameter group or parameter different leds related to the parameter group or parameter are displayed 8
- Working with the units 8
- Adjusting the cooling temperature setpoint 9
- How to consult and modify the direct parameters 9
- How to consult the sensor readout menu parameters 9
- Switching the unit off 9
- Switching the unit on 9
- Consulting actual operational information 10
- Resetting alarms 10
- Resetting warnings 10
- Advanced features of the digital controller 11
- Overview of the direct and user parameters 11
- The list of direct parameters is accessible by pressing the b key for approximately 5 seconds refer also to how to consult and modify the direct parameters on page 8 11
- This chapter gives an overview of the direct parameters and user parameters provided by the controller in the following chapter you will learn how you can set up and configure the unit using these parameters 11
- Defining the cooling temperature differential 12
- Defining the heating temperature differential 12
- How to consult and modify the user parameters 12
- Defining the measurement unit 13
- Defining the time delay between pump and compressor startup 13
- Defining the time delay between unit and pump shutdown 13
- Defining the timer threshold for maintenance warning 13
- Selecting dual setpoint control 13
- Selecting local or remote cool heat control 13
- Selecting local or remote on off control 13
- Bms connection modbus 14
- Connection modbus 14
- Different parts of the communication network 14
- General description of modbus 14
- General information about the modbus protocol 14
- Implemented commands for the modbus protocol 14
- Implemented rs485 communication settings for the modbus protocol 14
- Locking the controller keyboard 14
- 0 for off 15
- 1 for on 15
- Activating the modbus protocol 15
- All digital variables are assigned to bits of consecutive registers each one having 15
- Analogue and integer data an analogue and integer value is represented by a 16 bit word register in binary notation for each register the first byte contains the high order bits and the second byte contains the low order bits 15
- Data representation of the modbus protocol 15
- Defining the bms setting 15
- Defining the bms setting 15
- Defining the unit s serial address 15
- Digital all digital data is coded by a single bit 15
- For addresses of all the direct and user parameters refer to overview of the direct and user parameters on page 10 15
- Implemented error code 15
- In case the bms or supervisory system tries to write a value of a parameter that is out of range the writing will be ignored 15
- Overview of all variables which are not direct or user parameters 15
- The address card operates on registers where one register must be considered at 16 bit 15
- The analogue variables are represented in tenths for example the value 10 is transmitted as 0064h 100d for example the value 10 is transmitted as ff9ch 100d 15
- The bms or supervisory system and the chiller unit communicate through a fixed set of variables also called address numbers hereafter you will find the information you need about the digital integer and analogue variables that the bms or supervisory system can read from or write to the address card of the chiller 15
- The higher address variable assigned to the most significant bit 15
- The integer variables are transferred using the effective value for example the value 100 is transmitted as 0064h 100d 15
- The lower address variable assigned to the less significant bit 15
- The modbus protocol is activated by setting the h23 parameter to 1 15
- This is a user parameter refer to how to consult and modify the user parameters on page 11 15
- To define each unit s unique serial address required for communication with the supervisionary system set parameter h10 15
- Variables database 15
- Before contacting your local dealer read this chapter carefully it will save you time and money 16
- Before starting the trouble shooting procedure carry out a thorough visual inspection of the unit and look for obvious defects such as loose connections or defective wiring 16
- Roubleshooting 16
- This section provides useful information for diagnosing and correcting certain troubles which may occur in the unit 16
- Troubleshooting 16
- When a safety device was activated stop the unit and find out why the safety device was activated before resetting it under no circum stances safety devices may be bridged or changed to a value other than the factory setting if the cause of the problem cannot be found call your local dealer 16
- When carrying out an inspection on the supply panel or on the switch box of the unit always make sure that the circuit breaker of the unit is switched off 16
- Aintenance 17
- Disposal requirements 17
- Important information regarding the refrigerant used 17
- Maintenance 17
- Maintenance activities 17
- Annex i 18
- Saturated temperature 18
- Menu overview 19
Похожие устройства
- Daikin EWLP026KBW1N Инструкция по эксплуатации
- Daikin EWLP030KBW1N Инструкция по монтажу
- Daikin EWLP030KBW1N Руководство по эксплуатации
- Daikin EWLP030KBW1N Размерный чертеж
- Daikin EWLP030KBW1N Инструкция по эксплуатации
- Daikin EWLP040KBW1N Инструкция по монтажу
- Daikin EWLP040KBW1N Размерный чертеж
- Daikin EWLP040KBW1N Инструкция по эксплуатации
- Daikin EWLP040KBW1N Руководство по эксплуатации
- Daikin EWLP055KBW1N Инструкция по монтажу
- Daikin EWLP055KBW1N Руководство по эксплуатации
- Daikin EWLP055KBW1N Размерный чертеж
- Daikin EWLP055KBW1N Инструкция по эксплуатации
- Daikin EWLP065KBW1N Инструкция по монтажу
- Daikin EWLP065KBW1N Инструкция по эксплуатации
- Daikin EWLP065KBW1N Размерный чертеж
- Daikin EWLP065KBW1N Руководство по эксплуатации
- Sennheiser M2 OEBT Black Инструкция по безопасности
- Sennheiser M2 OEBT Black Руководство пользователя
- Sennheiser HE 1 Инструкция по эксплуатации