![Mipro ACT707DE [3/9] Dual channel receiver dual channel receiver](/img/pdf.png)
Mipro ACT707DE [3/9] Dual channel receiver dual channel receiver
![Mipro ACT707DE [3/9] Dual channel receiver dual channel receiver](/views2/1665427/page3/bg3.png)
2 3
DUALCHANNELRECEIVER DUALCHANNELRECEIVER
2.PARTSNAMESANDFUNCTIONS
FrontPanel：
RearPanel：
(Fig.1)
(Fig.2)
POWER
(1) (2)(3)(4)(5)
(6)(7)
(8)(9)(10)(11)
(12)(13)
ACT-707DE
SCAN SCANACT ACTRF RFAUDIO AUDIO
SIGNAL SIGNAL
A B
(24)
+8VDCBIAS
3:COLD
1:GND
2:HOT
MADEINTAIWAN
SQB BALANCEDOUTADCIN(12~15V)LEVELMIXOUTANTENNAB BALANCEDOUTB SQA ANTENNAA
MIC LINE
+8VDCBIAS
(14)
(15)
(16)(17) (18) (19) (20) (21) (22) (23)
(1)PowerSwitch&Indicator:Whenswitchisturnedon,redindicator
illuminatestodenotenormalpowerstatus.
(2)(8)AudioSignalLevelIndicator:Indicatetheaudiosignallevel.
(3)(9)RFSignalLevelIndicator:IndicatetheRFsignalstrengthreceived.
(4)(10)ACTButton:Tosetupmicrophonefrequencytomatchreceiver
frequency.
(5)(11)ScanButton:Pressoncetoselectreceivingchannelandautoscan
thewholebandwidthtoavoidinterferencechannel.
(6)(12)ACTIndicator:IndicateifACTfunctionisactivated.
(7)(13)ChannelIndicator:Todisplaysystem'sreceivingchannel.
(14)RearAntennaBinputConnector:BAntennaconnectorcanbe
installedwithantennadirectlyandprovidespowerforantenna
booster..
(15)(20)BalancedAudioOutputJack:WithCannon/XLRtypeconnector
providesbalancedaudiooutputsignalfromthisjacktotheamplifier.
(16)UnbalancedAudioMixedOutputJack:With1/4PhoneJack
providesthemixedunbalancedaudiooutputsignalfromthisjackto
theamplifier.Switchbetween"LINE"and"MIC"fordifferentpurposes.
(17)UnbalancedLevelSwitch:"MIC"selectionisfor"Microphone-level"
output."LINE"selectionisfor"Line-out"leveloutput.
(18)DC12VInputJack:Toconnect12VDCfromtheAC/DCadapter.
(19)(21)SquelchAdjuster:AdjustthesquelchleveltoeliminatetheRFnoise
interferenceatreceiverstand-bystate.
(22)ACInputJack:Toconnect85~265VoltsACpower.
(23)RearAntennaAinputConnector:AAntennaconnectorcanbe
installedwithantennadirectlyandprovidespowerforantenna
booster.
(24)RackmountBracket:ToinstallthereceiverintoanEIA19-inch
standardrackcase.
λ
Switchbetween"LINE"and"MIC"fordifferentpurposes.
Содержание
- Act 707de dual channel wireless receiver act 707de channel wireless receiver dual 1
- Disposal 1
- Electronics co ltd 1
- Instruction manual 1
- Belt pack transmitter 2
- Contents dual channel receiver 2
- Dual channel receiver 2
- Handheld wireless microphone 2
- Included accessories 2
- Introduction 2
- Operating instructions 2
- Dual channel receiver dual channel receiver 3
- Parts names and functions 3
- Audio output connection 4
- Dual channel receiver dual channel receiver 4
- Fig fig 4
- Install 2 separate antennas o n the antenna sockets 14 23 on the rear panel illustrated in figure 3 4
- Installation of the receiver 4
- On the front panel of the receiver 4 openings are pre drilled for instant installation on the standard 19 inch rack case shows in figure 8 4
- Poweroutput connection 4
- To ensure best reception possible receiver must be installed at least one meter above ground in addition the distance between transmitter and receiver must be more than one meter and away from noise shows in figure 7 4
- Dual channel receiver dual channel receiver 5
- Receiver operating procedures 5
- Switchable channels functions 5
- Act button 6
- Cautions 6
- Dual channel receiver dual channel receiver 6
- Battery insertion 7
- Cautions 7
- Handheld wireless microphone handheld wireless microphone 7
- Operating instructions 7
- Parts names and functions 7
- Belt pack transmitter belt pack transmitter 8
- Operating instructions 8
- Parts names and functions 8
- Af 4 pin input connection methods 9
- Battery installation 9
- Belt pack transmitter belt pack transmitter 9
- Cautions 9
- Insert a 9vbattery into the battery compartment according to the correct polarity as shown in fig 4 then push up to close the battery compartment as shown in fig 4 9
- Pushing down both snap locks o n the sides of battery cover toopen battery cover take out the batteries fig 3 9
- Under normal operation when receiver and transmitter are paired together to set frequency microphone indicator 3 will remain off after act setup the frequency however if indicator 3 is flashing it means receiver and transmitter are not in the same frequencyband please check the stickers on transmitter and receiver to observe if they are sharing the same frequency bands 9
Похожие устройства
- Mipro ACT707HM Инструкция по эксплуатации
- Mipro ACT707S Инструкция по эксплуатации
- Mipro ACT707SE Инструкция по эксплуатации
- Mipro ACT707TM Инструкция по эксплуатации
- Mipro ACT81 Инструкция по эксплуатации
- Mipro ACT82 Инструкция по эксплуатации
- AXIOMET AX-T02 Расширенная инструкция
- AXIOMET AX-T02 Инструкция
- AXIOMET AX-T03 Инструкция
- AXIOMET AX-T03 Расширенная инструкция
- Mipro ACT8H Инструкция по эксплуатации
- AXIOMET AX-T01 Расширенная инструкция
- AXIOMET AX-T01 Инструкция
- Mipro ACT8T Инструкция по эксплуатации
- Mipro AD-808 Инструкция по эксплуатации
- AXIOMET AX-TI220 Инструкция
- AXIOMET AX-TI220 Расширенная инструкция
- AXIOMET AX-T2400 Инструкция
- AXIOMET AX-T2400 Расширенная инструкция
- AXIOMET AX-T2200 Инструкция