Mipro ACT707S Инструкция по эксплуатации онлайн
2CE149
ElectronicsCo.,Ltd.
Headoffice:814,Pei-KangRoad,Chiayi,600,Taiwan.
Taipeioffice:5,Lane118,Sung-tehRoad,100,Taipei,Taiwan.
Web-http://www.mipro.com.tw
E-mail:@mipro.com.twmipro
ACT-707SSingleChannelWirelessReceiver
InstructionManual
ACT-707SChannelWirelessReceiverSingle
B
Содержание
- Act 707s channel wireless receiver single 1
- Act 707s single channel wireless receiver 1
- Electronics co ltd 1
- Instruction manual 1
- Act single channel wireless receiver 2
- Belt pack transmitter 2
- Contents act single channel wireless receiver 2
- Handheld wireless microphone 2
- Included accessories 2
- Introduction 2
- Operating instructions 2
- Act single channel wireless receiver act single channel wireless receiver 3
- Parts name and functions 3
- Act single channel wireless receiver act single channel wireless receiver 4
- Installation of the receiver 4
- Receiver operating procedures 4
- 2 inch units receiver installation 5
- Act single channel wireless receiver 5
- Act single channel wireless receiver act single channel wireless receiver 6
- Designations of buttons and functions 6
- G ch freq sq vol name remo 6
- Operation of receiver with lcd display panel 6
- Act single channel wireless receiver act single channel wireless receiver 7
- Exit menu 7
- Freq menu 7
- Sq menu 7
- The operation provids mute control switch 7
- Act single channel wireless receiver act single channel wireless receiver 8
- Exit menu 8
- Name menu 8
- Act single channel wireless receiver act single channel wireless receiver 9
- Computer network interface operation 9
- Except for receiver module both receiver with lcd display have the most advance function of computer network interfaced controlling system 9
- Wiring instruction 9
- Act single channel wireless receiver 10
- Cautions 10
- Battery insertion 11
- Functions of lcd display 11
- Grille protects cartridge prevents pop noise and prevents microphone from rolling with polygonal shape 2 color ring for frequency differentiation 3 housing upper portion to be connected to a capsule module and battery internally it holds transmitter pcb 4 functions of lcd display 5 battery compartment designed to accommodate two 1 v aa batteries 6 battery cap covers battery in the battery compartment 7 anti roll ring for frequency differentiation 8 act signal receptor receiving act signal and adjusting frequency automatically 11
- Handheld wireless microphone handheld wireless microphone 11
- Insert two 1 v aa batteries correctly into the battery compartment with the positive pole points at the microphone capsule then screw the battery cap 6 back to microphone as shown in fig 2 11
- Parts names and functions 11
- Ps when the microphone is not in use make sure the power of the microphone is off if the microphone will not be used for some time please remove the batteries from the battery compartment to avoid battery leakage and result in damaged battery springs and circuit if a rechargeable battery was used take it out and recharge it 11
- Unscrew battery cap 6 in a counter clockwise direction 11
- Belt pack transmitter belt pack transmitter 12
- Parts names and functions 12
- Af 4 pin input connection methods 13
- Before power on ascertain if same channel 7 was set up for both receiver and microphone if not adjust to same channel accordingly 13
- Belt pack transmitter belt pack transmitter 13
- Operating instructions 13
- Plug the microphone connector into the input jack 1 and tighten the connector screw by clockwise direction as shown in fig 2 13
- The led indicator flashes briefly when power on indicating normal battery status if no flash occurs it has either no battery the battery is drained or installed incorrectly change accordingly 13
- To adjust gt mt switch 10 and gain control 8 simply push down both snap locks on the sides of battery cover and flip it backwards to expose the adjustment panel 13
- Battery installation 14
- Belt pack transmitter belt pack transmitter 14
- Functions of lcd display 14
- Insert a two 1 aa batteries into the battery compartment according to the correct polarity as shown in fig 3 then push up to close the battery compartment as shown in fig 4 14
- Ps when the microphone is not in use make sure the power of the microphone is off if the microphone will not be used for some time please remove the batteries from the battery compartment to avoid battery leakage and result in damaged battery springs and circuit if a rechargeable battery was used take it out and recharge it 14
- Pushing down both snap locks on the sides of battery cover to open battery cover take out the batteries fig 3 14
Похожие устройства
- Mipro ACT707SE Инструкция по эксплуатации
- Mipro ACT707TM Инструкция по эксплуатации
- Mipro ACT81 Инструкция по эксплуатации
- Mipro ACT82 Инструкция по эксплуатации
- AXIOMET AX-T02 Расширенная инструкция
- AXIOMET AX-T02 Инструкция
- AXIOMET AX-T03 Инструкция
- AXIOMET AX-T03 Расширенная инструкция
- Mipro ACT8H Инструкция по эксплуатации
- AXIOMET AX-T01 Расширенная инструкция
- AXIOMET AX-T01 Инструкция
- Mipro ACT8T Инструкция по эксплуатации
- Mipro AD-808 Инструкция по эксплуатации
- AXIOMET AX-TI220 Инструкция
- AXIOMET AX-TI220 Расширенная инструкция
- AXIOMET AX-T2400 Инструкция
- AXIOMET AX-T2400 Расширенная инструкция
- AXIOMET AX-T2200 Инструкция
- AXIOMET AX-T2200 Расширенная инструкция
- AXIOMET AX-T903 Расширенная инструкция