![Gigabyte X299 AORUS Gaming 7 Pro (rev. 1.0) [24/152] Center subwoofer speaker out](/img/pdf.png)
Gigabyte X299 AORUS Gaming 7 Pro (rev. 1.0) [24/152] Center subwoofer speaker out
![Gigabyte X299 AORUS Gaming 7 Pro (rev. 1.0) [24/152] Center subwoofer speaker out](/views2/1666724/page24/bg18.png)
Hardware Installation
- 24 -
MMCX Antenna Connectors (2T2R)
Use this connector to connect an antenna.
• Whenremovingthecableconnectedtoabackpanelconnector,rstremovethecablefromyour
device and then remove it from the motherboard.
• When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent
an electrical short inside the cable connector.
• If you want to install a Side Speaker, you need to retask either the Line in or Mic in jack to be Side
Speaker out using the HD Audio Manager application
.
• Refertotheinstructionsonsettingupa2/4/5.1/7.1-channelaudiocongurationinChapter6,
"Conguring2/4/5.1/7.1-ChannelAudio."
Center/Subwoofer Speaker Out
Usethisaudiojacktoconnectcenter/subwooferspeakersina5.1/7.1-channelaudioconguration.
Rear Speaker Out
Thisjackcanbeusedtoconnectrearspeakersina4/5.1/7.1-channelaudioconguration.
Optical S/PDIF Out Connector
This connector provides digital audio out to an external audio system that supports digital optical audio.
Before using this feature, ensure that your audio system provides an optical digital audio in connector.
Line In
The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out
The line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to
connectfrontspeakersina4/5.1/7.1-channelaudioconguration.
Mic In
The Mic in jack.
Tighten the antenna cables to the antenna connectors and then move the antenna to a place
where the signal is good.
Содержание
- Rev 1002 12me x29ag7p 1002r 1
- User s manual 1
- X299 aorus gaming 7 pro 1
- Motherboard 2
- See the latest safety and regulatory documents at gigabyte s website 2
- Sept 28 2017 2
- Wireless module country approvals 2
- X299 aorus gaming 7 pro 2
- Copyright 3
- Disclaimer 3
- Documentation classifications 3
- Identifying your motherboard revision 3
- Box contents optional items x299 aorus gaming 7 pro motherboard chapter 1 hardware installation 4
- Chapter 2 bios setup 3 4
- Chapter 4 drivers installation 3 4
- Chapter3configuringaraidset 1 4
- Table of contents 4
- 1 bios update utilities 95 5
- 1 killer control center 129 5
- 2 app center 100 5
- 2 configuringaudioinputandoutput 130 5
- 3 troubleshooting 138 5
- 4 debug led codes 141 5
- Chapter 5 unique features 5 5
- Chapter 6 appendix 29 5
- Regulatory statements 145 contact us 151 5
- Box contents 6
- Optional items 6
- Note for debug code information please refer to chapter 6 7
- X299 aorus gaming 7 pro 7
- X299 aorus gaming 7 pro motherboard 7
- 1 installation precautions 9
- Chapter 1 hardware installation 9
- 2 product specifications 10
- 2 productspecifications 10
- 3 1 installing the cpu 14
- 3 installing the cpu and cpu cooler 14
- 3 2 installing the cpu cooler 16
- 17 hardware installation 17
- 4 1 4 channel dual channel memory configuration 17
- 4 1 4channel dualchannelmemoryconfiguration 17
- 4 installing the memory 17
- Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage 17
- Channel a ddr4_2_1a ddr4_4_2a 17
- Channel b ddr4_1_1b ddr4_3_2b 17
- Channel c ddr4_2_1c ddr4_4_2c 17
- Channel d ddr4_1_1d ddr4_3_2d 17
- Ddr4_1_1b ddr4_2_1c or ddr4_1_1d 17
- Memory modules have a foolproof design a memory module can be installed in only one direction if you are unable to insert the memory switch the direction 17
- Note wheninstallingthememory makesuretobeginwiththefirstsocketofeachchannel suchasddr4_2_1a 17
- Read the following guidelines before you begin to install the memory make sure that the motherboard supports the memory it is recommended that memory of the same capacity brand speed and chips be used go to gigabyte s website for the latest supported memory speeds and memory modules 17
- Refer to the table below for memory installation according to the number of the memory modules you want to install 17
- When using a 44 lane 28 lane cpu 6 core or above this motherboard supports 4 channel technology after the memory is installed the bios will automatically detectthespecificationsandcapacityofthememory theeightddr4memorysocketsaredividedintofour channels and each channel has two memory sockets as following 17
- Channel a ddr4_2_1a ddr4_4_2a 18
- Channel b ddr4_1_1b ddr4_3_2b 18
- Dual channel mode cannot be enabled if only one memory module is installed 18
- Dualchannelmemoryconfigurationstable 18
- Due to cpu limitations read the following guidelines before installing the memory in dual channel mode 18
- Hardware installation 18 18
- When enabling dual channel mode with two or four memory modules it is recommended that memory of the same capacity brand speed and chips be used 18
- When using a 16 lane cpu 4 core this motherboard supports dual channel technology after the memory is installed the bios will automatically detectthespecificationsandcapacityofthememory thefourmemorysocketsaredividedintotwochannels and each channel has two memory sockets as following 18
- 4 2 installing a memory 19
- 5 installing an expansion card 20
- 21 hardware installation 21
- 6 setting up amd crossfir 21
- 6 setting up amd crossfire nvidia sli configuration 21
- A system requirements 21
- B connecting the graphics cards 21
- Configuration 21
- Crossfire 21
- Note 1 when using dual core graphics cards only 2 way is supported note 2 the bridge connector s may be needed or not depending on your graphics cards note 3 supports the crossfire technology only 21
- Procedure and driver screen for enabling crossfire sli technology may differ by graphics cards and driver version refer to the manual that came with your graphics cards for more information about enabling crossfire sli technology 21
- Refer to the table below when using a 16 lane cpu 4 core 21
- Refer to the table below when using a 28 lane cpu 6 core or above 21
- Refer to the table below when using a 44 lane cpu 10 core or above 21
- Sli bridge connectors apowersupplywithsufficientpowerisrecommended refertothemanualofyourgraphicscardsforthe power requirement 21
- Sli bridge connectors in the crossfire sli gold edge connectors on top of the cards step 3 plug the display cable into the graphics card on the pciex16_1 slot 21
- Step 1 observe the steps in 1 5 installing an expansion card and install crossfire sli graphics cards on the pci express x16 slots step 2 insert the crossfire 21
- Website 21
- Windows 10 64 bit operating system a crossfire sli supported motherboard with two or more pci express x16 slots and correct driver crossfire sli ready graphics cards of identical brand and chip and correct driver for the latest gpus that support the 3 way crossfire sli technology please refer to the amd nvidi 21
- C configuringthegraphicscarddriver 22
- 23 hardware installation 23
- 7 back panel connectors 23
- Intothisportfirst 23
- Note theusbflashdriveusedmustbeausb2 flashdrive 23
- Ps 2 keyboard mouse port 23
- Rj 45 lan port lan1 23
- Rj 45 lan port lan2 23
- The gigabit ethernet lan port provides internet connection at up to 1 gbps data rate the following describes the states of the lan port leds 23
- Thereversibleusbportsupportstheusb3 gen2specificationandiscompatibletotheusb3 gen 1andusb2 specification usethisportforusbdevices 23
- Theusb3 gen1portsupportstheusb3 gen1specificationand is compatible to the usb 2 specification usethisportforusbdevices beforeusingq flashplus makesuretoinserttheusb flashdriv 23
- Theusb3 gen1portsupportstheusb3 gen1specificationandiscompatibletotheusb2 specification usethisportforusbdevices 23
- Theusb3 gen2type aportsupportstheusb3 gen2specificationandiscompatibletotheusb 3 gen1andusb2 specification usethisportforusbdevices 23
- Usb 3 gen 1 port 23
- Usb 3 gen 1 port white 23
- Usb 3 gen 2 type a port red 23
- Usb type 23
- Use this port to connect a ps 2 mouse or keyboard 23
- Center subwoofer speaker out 24
- Line in 24
- Line out 24
- Mic in 24
- Mmcx antenna connectors 2t2r 24
- Optical s pdif out connector 24
- Rear speaker out 24
- 8 onboard leds and buttons 25
- Quick buttons 25
- Status leds 25
- Eco button and oc button 26
- 9 installing the mmcx antenna connectors 2t2r 27
- 10 internal connectors 28
- 2 atx_12v_2x4_1 atx_12v_2x4_2 atx 2x4 12v power connectors and 2x12 main 29
- 29 hardware installation 29
- Power connector 29
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start 29
- To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system 29
- With the use of the power connector the power supply can supply enough stable power to all the components onthemotherboard beforeconnectingthepowerconnector firstmakesurethepowersupplyisturned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation 29
- 4 cpu_fan sys_fan1 sys_fan2 sys_fan3 sys_fan4 fan headers 30
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the motherboard supports cpu fan speed control which requires the use of a cpu fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis 30
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from overheating overheating may result in damage to the cpu or the system may hang 30
- Hardware installation 30 30
- Sys_fan5_pump sys_fan6_pump system fan water cooling pump headers 30
- The fan pump headers are 4 pin and possess a foolproof insertion design most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis the header also provides speed control for a water cooling pump refer to chapter 2 bios setup m i t for more information 30
- Thesefanheadersarenotconfigurationjumperblocks donotplaceajumpercapontheheaders 30
- Cpu_opt water cooling cpu fan header 31
- Ec_temp1 ec_temp2 temperature sensor headers 31
- For how to turn on off the i o shield led indicators refer to the instructions on in chapter 2 bios setup peripherals or chapter 5 unique features app center rgb fusion 32
- Hardware installation 32 32
- Led_io i o shield audio led power connector 32
- Pin no definition 1 5v 2 red 3 green 4 blue 32
- Step 1 install the included i o shield into the chassis for actual installation please refer to the user guide for your chassis step 2 place the motherboard into the chassis aligning the back panel connectors with the installed i o shield connect the power cable from the i o shield to the led_io connector on the motherboard 32
- The power connector provides power to the leds on the i o shield on the motherboard back panel 32
- D_led digital led strip header 33
- Dled_v_sw digital led strip power select jumper 33
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices 34
- Chipset supports raid 0 raid1 raid5 andraid10 refertochapter3 configuringaraidset forinstructionsonconfiguring a raid array 34
- Connect one end of the rgb rgbw led strip extension cable to the header and the other end to your rgb rgbw led strip the black wire marked with a triangle on the plug of the extension cable must be connected to pin 1 12v of this header the 12v pin marked with an arrow on the other end of the extension cable must be lined up with the 12v of the led strip be careful with the connection orientation of the led strip incorrect connection may lead to the damage of the led strip if you are connecting a rgbw led strip 5 pin combine the twoplugsoftheextensioncabletogetherfirst ifyouareconnectinga rgb led strip 4 pin use only the 4 pin plug of the extension cable 34
- For how to turn on off the lights of the led strip refer to the instructions on in chapter 2 bios setup peripherals or chapter 5 unique features app center rgb fusion 34
- Hardware installation 34 34
- Led_c1 led_c2 rgb rgbw led strip headers 34
- Pin no definition 1 12v 2 g 3 r 4 b 5 w 34
- Pin no definition 1 gnd 2 txp 3 txn 4 gnd 5 rxn 6 rxp 7 gnd 34
- Sata3 0 1 2 3 4 5 6 7 sata 6gb s connectors 34
- The headers can be used to connect a standard 5050 rgb rgbw led strip 12v g r b w with maximum power rating of 2a 12v and maximum length of 2m 34
- The sata connectors conform to sata 6gb s standard and are compatible with sata 3gb s and sata 1 gb s standard each sata connector supports a single sata device the inte 34
- To enable hot plugging for the sata ports refer to chapter 2 bios setup peripherals sata andrstconfiguration formoreinformation 34
- 35 hardware installation 35
- Follow the steps below to correctly install an m ssd in the m connector 35
- M2p_32g m2m_32g 35
- M2q_32g m socket 3 connectors 35
- Note the m2m_32g connector must work with an inte 35
- Select the proper hole for the m ssd to be installed and refasten the screw and standoff 35
- Step 1 get a screw and a standoff from the included m screw kit locate the m connector where you will install the m ssd use a screwdriver to unfasten the screw on the heatsink and then remove the heatsink only the m2q_32g connector has the heatsink 35
- Step 2 locate the proper mounting hole for the m ssd tobeinstalledandthentightenthestandofffirst insert the m ssd into the m connector at an angle 35
- Step 3 press the m ssd down and then secure it with the screw replace the heatsink and secure it to the original hole 35
- Step 4 the installation is completed as shown in the picture above 35
- Them connectorssupportm satassdsorm pciessdsandsupportraidconfiguration please note that an m pcie ssd cannot be used to create a raid set either with an m sata ssd or a sata harddrive tocreatearaidarraywithanm pciessd youmustsetuptheconfigurationinuefibios mode refertochapter3 configuringaraidset forinstructionsonconfiguringaraidarray 35
- Vrocupgradekeytosupportraidconfiguration 35
- Due to the limited number of lanes provided by the chipset the availability of the sata connectors may be affected by the type of device installed in the m2p_32g and m2q_32g connectors the m2p_32g connector shares bandwidth with the sata3 0 connector the m2q_32g connector shares bandwidth with the sata3 4 5 6 7 connectors refer to the following tables for details 36
- Hardware installation 36 36
- Installation notices for the m and sata connectors 36
- M2m_32g 36
- M2p_32g 36
- M2q_32g 36
- F_panel front panel header 37
- F_audio front panel audio header 38
- For information about connecting the s pdif digital audio cable carefully read the manual for your expansion for information about connecting the s pdif digital audio cable carefully read the manual for your expansion card 38
- Hardware installation 38 38
- Pin no definition 1 mic2_l 2 gnd 3 mic2_r 4 nc 5 line2_r 6 sense 7 gnd 8 no pin 9 line2_l 10 sense 38
- Pin no definition 1 spdifo 2 gnd 38
- Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer 38
- Spdif_o s pdif out header 38
- Thefrontpanelaudioheadersupportshighdefinitionaudio hd youmayconnectyourchassisfront panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it 38
- This header supports digital s pdif out and connects a s pdif digital audio cable provided by expansion cards for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards for example some graphics cards may require you to use a s pdif digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an hdmi display to the graphics card and have digital audio output from the hdmi display at the same time 38
- 39 hardware installation 39
- F_usb30_1 f_usb30_2 usb 3 gen 1 headers 39
- F_usb31c usb type 39
- Header with usb 3 gen 2 support 39
- Pin no definition pin no definition 1 vbus 11 d2 2 ssrx1 12 d2 3 ssrx1 13 gnd 4 gnd 14 sstx2 5 sstx1 15 sstx2 6 sstx1 16 gnd 7 gnd 17 ssrx2 8 d1 18 ssrx2 9 d1 19 vbus 10 nc 20 no pin 39
- Pin no definition pin no definition 1 vbus 11 vbus 2 tx1 12 tx2 3 tx1 13 tx2 4 gnd 14 gnd 5 rx1 15 rx2 6 rx1 16 rx2 7 vbus 17 gnd 8 cc1 18 d 9 nc 19 d 10 nc 20 cc2 39
- Prior to installing the usb front panel be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the usb front panel 39
- Theheaderconformstousb3 gen2specificationandcanprovideoneusbport 39
- Theheadersconformtousb3 gen1andusb2 specificationandeachheadercanprovidetwousb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer 39
- Add in card 40
- Add in card connector 40
- Do not plug the ieee 1394 bracket 2x5 pin cable into the usb 2 1 header prior to installing the usb bracket be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the usb bracket 40
- F_usb1 f_usb2 usb 2 1 headers 40
- Hardware installation 40 40
- Pin no definition 1 power 5v 2 power 5v 3 usb dx 4 usb dy 5 usb dx 6 usb dy 7 gnd 8 gnd 9 no pin 10 nc 40
- Supports a thunderbol 40
- Thb_c thunderbol 40
- Theheadersconformtousb2 1 specification eachusbheadercanprovidetwousbportsviaan optional usb bracket for purchasing the optional usb bracket please contact the local dealer 40
- This connector is for a gigabyte thunderbol 40
- 41 hardware installation 41
- Always turn off your computer and unplug the power cord before replacing the battery replace the battery with an equivalent one damage to your devices may occur if the battery is replaced with an incorrect model 41
- B s_ b 41
- B_ f_usb3 41
- Bat battery 41
- Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the battery model 41
- F_usb3 f 41
- F_usb30 f_ u 41
- Lad0 2 vcc3 3 lad1 4 no pin 5 lad2 6 lclk 7 lad3 8 gnd 9 lframe 10 nc 11 serirq 12 lreset 41
- Pin no definition 41
- Replace the battery 4 plug in the power cord and restart your computer 41
- S 3 b s s s 41
- S b_ b 41
- Thebatteryprovidespowertokeepthevalues suchasbiosconfigurations date andtimeinformation in the cmos when the computer is turned off replace the battery when the battery voltage drops to a low level or the cmos values may not be accurate or may be lost 41
- Tpm trusted platform module header 41
- Usb 0_ b 41
- Used batteries must be handled in accordance with local environmental regulations 41
- When installing the battery note the orientation of the positive side and the negative side of the battery the positive side should face up 41
- You may clear the cmos values by removing the battery 1 turn off your computer and unplug the power cord 2 gently remove the battery from the battery holder and wait for one minute or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds 41
- You may connect a tpm trusted platform module to this header 41
- _ s s_ _ b 41
- _ u _ b 41
- Hardware installation 42 42
- This header can be used to connected an inte 42
- Vroc inte 42
- Vroc upgrade key 42
- Vroc upgrade key header 42
- Chapter 2 bios setup 43
- 1 startup screen 44
- 2 the main menu 45
- Classic setup 45
- Classic setup function keys 45
- Sample bios version f1a 45
- B easy mode 46
- 3 m i t 47
- Advanced frequency settings 47
- Cpu bclk frequency 47
- Advanced cpu core settings 48
- Avx offset 48
- Bclk coarse rati 48
- Cpu clock ratio 48
- Cpu frequency 48
- Cpuclockratio cpufrequency 48
- Fclk frequency for early power o 48
- Pcie dmi peg frequency 48
- Spread spectrum contro 48
- Target cpu bclk frequency 48
- Active cores contro 49
- Avx 51 49
- Clr mesh frequency 49
- Clr mesh ratio 49
- Core current limit amps 49
- Cpu flex ratio overrid 49
- Cpu flex ratio setting 49
- Cpu pll tri 49
- Hyper threading technology 49
- Intel r turbo boost technology 49
- Mc pll tri 49
- No of cpu cores enable 49
- Pll trim threshol 49
- Power limit tdp watts power limit time 49
- Tjmax temperature 49
- Turbo per core limit contro 49
- Turbo rati 49
- Turbo residency tweak lut0 lut3 49
- C3 state support 50
- C6 c7 state support 50
- C8 state support 50
- Cpu eist function 50
- Cpu enhanced halt c1e 50
- Cpu thermal monitor 50
- Enhanced multi core performance 50
- Intel r speed shift technology inte 50
- Intel r turbo boost max technology 3 50
- Package c state limit 50
- Speed shift technology 50
- Adjacent cache line prefetch 51
- Energyefficientturb 51
- Extremememoryprofile x m p 51
- Hardware prefetcher 51
- Memory frequency mhz 51
- Memory odd ratio 100 133 or 200 266 51
- Memory ref clock 51
- Race to halt rth 51
- System memory multiplier 51
- Voltage optimizatio 51
- Advanced memory settings 52
- Extreme memory profile x m p 52
- Memory boot mod 52
- Memory enhancement settings 52
- Memory frequency mhz 52
- Memory timing mode 52
- Profile ddr voltage 52
- System memory multiplier memory ref clock memory odd ratio 100 133 or 200 266 52
- Channel a b 53
- Channel interleaving 53
- Memory multiplier tweaker 53
- Memory sub timings 53
- Rank interleaving 53
- 3 v 5v pch core 12v 56
- Case open 56
- Cpu mesh voltag 56
- Cpu vccsa cpu vccio dram channel a b voltage dram channel c d voltag 56
- Cpu vcor 56
- Cpu vri 56
- Internal cpu vcor 56
- Pc health status 56
- Reset case open status 56
- Fan control use temperature input 58
- Fan pump control mode 58
- Fan pump fail warning 58
- Fan pump stop 58
- Fan speed 58
- Fan speed control 58
- Flow rate 58
- Monitor 58
- Temperature 58
- Temperature interval 58
- Temperature warning control 58
- 4 system 59
- Access level 59
- System date 59
- System language 59
- System time 59
- 5 bios 60
- Boot option priorities 60
- Bootup numlock state 60
- Fast boot 60
- Full screen logo show 60
- Hard drive cd dvd rom drive floppy drive network device bbs priorities 60
- Security option 60
- Csm support 61
- Lan pxe boot option rom 61
- Mouse speed 61
- Network stack driver support 61
- Next boot after ac power loss 61
- Ps2 devices support 61
- Sata support 61
- Usb support 61
- Vga support 61
- Administrator password 62
- Other pci devices 62
- Storage boot option control 62
- User password 62
- 6 peripherals 63
- E2500lanchip lan2 63
- Ez raid 63
- Initial display output 63
- Onboard lan controller rivet networks kille 63
- Rear panel led 63
- Rgb fusion 63
- Front usb 3 _1 output voltage of usb ports provided by the onboard f_usb30_1 connector 64
- Front usb 3 _2 output voltage of usb ports provided by the onboard f_usb30_2 connector 64
- Intel platform trust technology ptt 64
- Ipv4 http support 64
- Ipv4 pxe support 64
- Ipv6 http support 64
- Ipv6 pxe support 64
- Ledsinsleep hibernation andsoftoffstates 64
- Network stack 64
- Networkstackconfiguration 64
- Trusted computing 64
- Aggressive lpm support 65
- Ip6configurationpolicy 65
- Legacy usb support 65
- Mass storage devices 65
- Media detect count 65
- Port 0 1 2 3 4 5 6 7 65
- Port 60 64 emulation 65
- Pxe boot wait time 65
- Sata controller s 65
- Sata mode selection 65
- Sataandrstconfiguration 65
- Usb mass storage driver support 65
- Usbconfiguration 65
- Xhci hand off 65
- Configuredasesata 66
- Hot plug 66
- Intel r ethernet connection lan1 66
- Mechanical presence switch 66
- 7 chipset 67
- Audio controller 67
- Intel vmd technolog 67
- Pch lan controller 67
- Wake on lan enable 67
- 8 power 68
- Ac back 68
- Dmi aspm 68
- Pch aspm 68
- Peg aspm 68
- Platform power management 68
- Power on by keyboard 68
- Power loading 69
- Power on by mouse 69
- Power on password 69
- Resume by alarm 69
- S3 save mode 69
- Soft off by pwr bttn 69
- 9 save exit 70
- Boot override 70
- Exit without saving 70
- Load optimized defaults 70
- Loadprofiles 70
- Save exit setup 70
- Saveprofiles 70
- 1 configuring sata controllers 71
- 1 configuringsatacontrollers 71
- A installing hard drives 71
- Beforeyoubegin pleasepreparethefollowingitems 71
- Chapter 3 configuring a raid set 71
- Chapter3 configuringaraidset 71
- Raid levels 71
- Tocreatearaidset followthestepsbelow 71
- B configuringsatacontrollermodeinbiossetup 72
- C 1 using ez raid 73
- C 2 uefiraidconfiguration 75
- 79 configuring a raid set 79
- C 3 configuringlegacyraidrom 79
- Enter the inte 79
- Figure 14 79
- Legacyraidbiossetuputilitytoconfigurearaidarray skipthisstepandproceedwiththe installationofwindowsoperatingsystemforanon raidconfiguration 79
- The main menu screen will appear figure 14 79
- Toentertheraidconfigurationutility 79
- Configuring a raid set 80 80
- Figure 15 80
- Figure 16 80
- To proceed 80
- 81 configuring a raid set 81
- Figure 17 81
- Figure 18 81
- Now you can proceed to install the sata raid ahci driver and operating system 81
- Or select 6 exit in main menu 81
- To cancel figure 17 81
- When completed you can see detailed information about the raid array in the disk volume information section including the raid level stripe block size array name and array capacity etc figure 18 81
- Before you begin 82
- Configuring a raid set 82 82
- Figure 19 82
- Figure 20 82
- Rapid recover technology provides data protection by allowing users to easily restore data and system operation using a designated recovery drive with the rapid recovery technology which employs raid 1 functionality users can copy the data from the master drive to the recovery drive if needed the data on the recovery drive can be restored back to the master drive 82
- Recovery volume options inte 82
- The recovery drive must have equal or greater capacity than the master drive a recovery volume can be created with two hard drives only a recovery volume and a raid array cannot co exist in the system at the same time that is if you have already created a recovery volume you are unable to create a raid array by default only the master drive can be viewed in the operating system the recovery drive is hidden 82
- 83 configuring a raid set 83
- Figure 21 83
- Figure 22 83
- On the create volume item to begin creating the recovery volume and follow the on screen instructions to complete 83
- Rapid storage technology utility in the operating system on request also allows users to restore the master drive to a previous state 83
- Step 4 under sync select continuous or on request figure 22 when set to continuous changes made to the data on the master drive will be automatically and continuously copied to the recovery drive when both hard drives are installed in the system on request allows users to update data from the master drive to the recovery drive manually using the inte 83
- Toconfirm figure21 83
- Acceleration options this option allows you to view the status of your accelerated drive volume figure 24 created using the inte 84
- Configuring a raid set 84 84
- Figure 23 84
- Figure 24 84
- Irst utility in case you are unable to run the inte 84
- Toabort 84
- Toconfirm 84
- 2 installing the raid ahci driver and operating system 85
- A installing windows 85
- B rebuilding an array 86
- 87 configuring a raid set 87
- Raidconfigurationutility onthe recovery volumes options menu select enable only recovery disk to show the recovery drive in theoperatingsystem followtheon screeninstructionstocompleteandexittheraidconfigurationutility 87
- Rapid storage technology utility and click recover data in manage volume 87
- Restoring the master drive to a previous state for recovery volume only when two hard drives are set to recovery volume in update on request mode you can restore the master drive data to the last backup state when needed for example in case the master drive detects a virus you can restore the recovery drive data to the master drive 87
- Step 1 select 4 recovery volume options in the main menu of the inte 87
- Step 2 go to the manage menu of the inte 87
- Step 3 click yes to begin the data recovery 87
- The status item on the left of the screen displays the recovering status after the recovery volume is completed the status will display as normal 87
- 3 installing an inte 88
- 3 installing an intel optane memory 88
- A system requirements 88
- B installation guidelines b 1 installation in ahci mode 88
- Configuring a raid set 88 88
- Ifthesatacontrollerhasbeenconfiguredinahcimode pleaseinstalltheoptan 88
- Lane cpu 4 core 2 inte 88
- Memory 88
- Memory 3 the optan 88
- Memory cannot be used to accelerate an existing raid array the accelerated hard drive ssd cannot be included in a raid array 88
- Memory in the m2p_32g or m2q_32g connector and follow the steps below 88
- Memory must have at least 16 gb capacity and it must have equal or smaller capacity than the hard drive ssd to be accelerated 88
- Note if the system already has inte 88
- Rapidstoragetechnologyutilityinstalled youhavetoremoveitfirst before installing the intel r optane tm memory system acceleration application 88
- The hard drive ssd to be accelerated must be a sata hard drive or m sata ssd and must have windows 10 64 bit or later version installed on it must be formatted for gpt partition 88
- The motherboard driver disk 88
- The optan 88
- 89 configuring a raid set 89
- After enabling the optan 89
- An optan 89
- B 2 installation in intel rst premium with intel optane system acceleration mode 89
- Do not abruptly remove the optan 89
- If you want to change remove the optan 89
- Ifthesatacontrollerhasbeenconfiguredinintelrstpremiumwithinteloptanesystemaccelerationmode please install the optan 89
- Memory cannot be used to accelerate an m pcie ssd if more than one optan 89
- Memory doing so will cause the operating system to stop functioning correctly 89
- Memory is installed you can select only one of them to accelerate your sata based boot drive the other s can only be used as data drive s 89
- Memory the related bios settings will remain even after a bios update 89
- Memory you must disable it using the inte 89
- Memoryinthem2p_32gorm2q_32gconnectorfirstandfollowthestepsbelow 89
- Rapid storage 89
- Technologyorintel r optanememoryapplicationfirst 89
- 4 configuring intel virtual raid on cpu intel vroc 90
- 4 configuringinte 90
- Installation guidelines a 1 hardware installation 90
- System requirements 90
- Virtual raid on cpu inte 90
- A 2 creating a raid array 91
- A 3 delete raid volume 92
- 1 drivers software 93
- Chapter 4 drivers installation 93
- 2 application software 94
- 3 information 94
- 1 1 updating the bios with the q flash utility 95
- 1 bios update utilities 95
- A before you begin 95
- Chapter 5 unique features 95
- B updating the bios 96
- 1 2 updating the bios with the bios utility 98
- A before you begin 98
- B using bios 98
- C after updating the bios 98
- 1 3 using q flash plus 99
- A before you begin 99
- B using q flash plus 99
- 2 app center 100
- Running the app center 100
- 2 1 3d osd 101
- The 3d osd interface 101
- Using 3d osd 101
- 2 2 autogreen 102
- The autogreen interface 102
- 2 3 bios setup 103
- The bios setup interface 103
- Using bios setup 103
- 2 4 color temperature 104
- The color temperature interface 104
- Using color temperature 104
- 2 5 cloud station 105
- Before you begin 105
- Homecloud 105
- The homecloud interface 105
- Using homecloud 106
- Gigabyte remote 107
- The gigabyte remote interface 107
- Using gigabyte remote 107
- Remote oc 108
- The remote oc interface 108
- Using remote oc 108
- Hotspot 109
- The hotspot interface 109
- Using hotspot 109
- 2 6 easytune 110
- Tabs information 110
- The easytune interface 110
- 2 7 easy raid 111
- Disk mode switch 111
- A system requirements 112
- B using xhd 112
- 2 8 fast boot 113
- The fast boot interface 113
- Using fast boot 113
- 2 9 game boost 114
- The game boost interface 114
- Using game boost 114
- 2 10 gigabyte hw oc app 115
- The gigabyte hw oc app interface 115
- Using gigabyte hw oc app 115
- 2 11 platform power management 116
- The platform power management interface 116
- Using platform power management 116
- 2 12 rgb fusion 117
- The rgb fusion interface 117
- Using rgb fusion 117
- 2 13 smart timelock 119
- The smart timelock interface 119
- Using smart timelock 119
- 2 14 smart keyboard 120
- The smart keyboard interface 120
- Using smart keyboard 120
- 2 15 smart backup 121
- Creating a backup 121
- Recoveringafile 121
- Saving the backup to a network location 121
- Recovering your system with smart backup 122
- 2 16 smart hud 123
- The smart hud interface 123
- Using smart hud 123
- 2 17 system information viewer 124
- Tabs information 124
- The system information viewer interface 124
- 2 18 usb blocker 125
- The usb blocker interface 125
- Using usb blocker 125
- 2 19 usb dac up 2 126
- The usb dac up 2 interface 126
- Using usb dac up 2 126
- 2 20 v tuner 127
- The v tuner interface 127
- Using v tuner 127
- 1 killer control center 129
- Chapter 6 appendix 129
- Overview 129
- Settings 129
- Wifi analyzer 129
- 2 1 configuring 2 4 5 7 channel audio 130
- 2 1 configuring2 4 5 7 channelaudio 130
- 2 configuring audio input and output 130
- 2 configuringaudioinputandoutput 130
- A configuring speakers 130
- B configuring sound effect 131
- C enabling smart headphone amp 131
- 2 2 configuring s pdif out 132
- 2 2 configurings pdifout 132
- Configuring the headphone 132
- 2 3 configuring microphone recording 133
- 2 3 configuringmicrophonerecording 133
- Enabling stereo mix 134
- 2 4 using the voice recorder 135
- A recording audio 135
- B playing the recorded sound 135
- 2 5 sound blasterx 720 136
- 3 1 frequently asked questions 138
- 3 troubleshooting 138
- Appendix 138 138
- To read more faqs for your motherboard please go to the support faq page on gigabyte s website 138
- 139 appendix 139
- 3 2 troubleshooting procedure 139
- If you encounter any troubles during system startup follow the troubleshooting procedure below to solve the problem 139
- Appendix 140 140
- If the procedure above is unable to solve your problem contact the place of purchase or local dealer for help or go to the support technical support page to submit your question our customer service staff will reply you as soon as possible 140
- 4 debug led codes 141
- Regular boot 141
- Recovery 143
- S3 resume 143
- Our commitment to preserving the environment 145
- Regulatory notices 145
- Regulatory statements 145
- Restriction of hazardous substances rohs directive statement 145
- Waste electrical electronic equipment weee directive statement 145
- Weee symbol statement 145
- Caution 146
- Fcc notice u s a only 146
- Canada industry canada ic 147
- European community radio equipment directive red compliance statement 148
- Japan wireless statement 148
- Korea kcc ncc wireless statement 148
- Taiwan ncc wireless statements 無線設備警告聲明 148
- 151 appendix 151
- Contact us 151
- Appendix 152 152
- Gigabyte esupport 152
- To submit a technical or non technical sales marketing question please link to http esupport gigabyte com 152
Похожие устройства
- Gigabyte X299 AORUS Gaming 7 (rev. 1.0) Инструкция
- Gigabyte X299 AORUS Gaming 3 Pro (rev. 1.0) Инструкция
- Gigabyte X299 AORUS Gaming 3 (rev. 1.0) Инструкция
- Gigabyte X299 AORUS Gaming (rev. 1.0) Инструкция
- Gigabyte C621 AORUS XTREME Инструкция
- Gigabyte X570 AORUS MASTER (rev. 1.0) Инструкция
- Gigabyte X570 AORUS ELITE WIFI (rev. 1.x) Инструкция
- Gigabyte X570 AORUS ELITE (rev. 1.0) Инструкция
- Gigabyte X399 AORUS XTREME (rev. 1.0) Инструкция
- Gigabyte X399 AORUS PRO (rev. 1.0) Инструкция
- Gigabyte X399 AORUS Gaming 7 (rev. 1.0) Инструкция
- Gigabyte TRX40 AORUS XTREME (rev. 1.1) Инструкция
- Gigabyte TRX40 AORUS XTREME (rev. 1.0) Инструкция
- Gigabyte TRX40 AORUS PRO WIFI (rev. 1.1) Инструкция
- Daikin EWWD910VZPS Инструкция по монтажу
- Daikin EWWD910VZPS Руководство по эксплуатации
- Daikin EWWD910VZPS Инструкция по эксплуатации
- Daikin EWWDC12VZPS Инструкция по монтажу
- Daikin EWWDC12VZPS Инструкция по эксплуатации
- Daikin EWWDC12VZPS Руководство по эксплуатации