Ardesto IR-C2232-BL [7/36] Anti calc system
![Ardesto IR-C2232-BL [7/36] Anti calc system](/views2/1712832/page7/bg7.png)
3
ANTI-CALC SYSTEM
A special resin filter inside the water reservoir softens the water and prevents scale
build-up in the plate. The resin filter is permanent and does not need replacing.
Please note:
Use tap water only. Distilled and/demineralised water makes the
“
Zero-Calc” anti-calc system ineffective by altering its physicochemical
characteristics.
Do not use chemical additives, scented substances or decalcifiers. Failure to
comply with the above-mentioned regulations leads to the loss of guarantee.
ANTI-DRIP SYSTEM
With the anti-drip system, you can perfectly iron even the most delicate fabrics.
Always iron these fabrics at low temperatures. The plate may cool down to the point
where no more steam comes out, but rather drops of
boiling water that can leave
marks or stains. In these cases, the Anti-drip system automatically activates to
prevent vaporization, so that you can iron the most delicate fabrics without risk of
spoiling or staining them.
AUTOMATIC SHUT OFF
The automatic shut off device trips after the iron has been left for approx. eight
minutes in the upright position or unused for approx. Thirty seconds in the horizontal
position. The light comes on to indicate that s
hut off has tripped. As soon as you
move the iron, the device turns off and the iron starts working again.
G E N E R A L I N S T R U C T I O N S
When using the iron for the first time, you may notice a slight emission of smoke
and hear some sounds made by the expanding plastics. This is quite normal and it
stops after a short time. We also recommend passing the iron over an ordinary cloth
before using it for the first time.
PREPARATIONS
Soft the laundry to be ironed according to the international symbols on the garment
label, or
if this is missing, according to the type of fabric.
GARMENT
LABEL
FABRIC
TYPE
THERMOSTAT
REGULATION
synthetic
·
low temperature
silk - wool
··
medium temperature
Cotton - linen
···
high temperature
Fabric not to be ironed
Start ironing the garments requiring a low temperature.
This reduces the waiting times (the iron takes less time to heat up than to cool down)
and eliminates the risk of scorching the fabric.
STEAM IRONING
Filling the reservoir
- Check that the plug is disconnected from the socket.
- Move the steam selector (3) to “0”
[Fig. 1].
- Open the lid (2).
- Raise the tip of the iron to help the water enter the opening without overflowing.
- Slowly pour the water i
nto the reservoir using the special measure (18) and taking
care not to go over the maximum level indicated by “MAX” on the reservoir
[Fig.
2]
.
- Close the lid (2).
3
ANTI-CALC SYSTEM
A special resin filter inside the water reservoir softens the water and prevents scale
build-up in the plate. The resin filter is permanent and does not need replacing.
Please note:
Use tap water only. Distilled and/demineralised water makes the
“
Zero-Calc” anti-calc system ineffective by altering its physicochemical
characteristics.
Do not use chemical additives, scented substances or decalcifiers. Failure to
comply with the above-mentioned regulations leads to the loss of guarantee.
ANTI-DRIP SYSTEM
With the anti-drip system, you can perfectly iron even the most delicate fabrics.
Always iron these fabrics at low temperatures. The plate may cool down to the point
where no more steam comes out, but rather drops of
boiling water that can leave
marks or stains. In these cases, the Anti-drip system automatically activates to
prevent vaporization, so that you can iron the most delicate fabrics without risk of
spoiling or staining them.
AUTOMATIC SHUT OFF
The automatic shut off device trips after the iron has been left for approx. eight
minutes in the upright position or unused for approx. Thirty seconds in the horizontal
position. The light comes on to indicate that s
hut off has tripped. As soon as you
move the iron, the device turns off and the iron starts working again.
G E N E R A L I N S T R U C T I O N S
When using the iron for the first time, you may notice a slight emission of smoke
and hear some sounds made by the expanding plastics. This is quite normal and it
stops after a short time. We also recommend passing the iron over an ordinary cloth
before using it for the first time.
PREPARATIONS
Soft the laundry to be ironed according to the international symbols on the garment
label, or
if this is missing, according to the type of fabric.
GARMENT
LABEL
FABRIC
TYPE
THERMOSTAT
REGULATION
synthetic
·
low temperature
silk - wool
··
medium temperature
Cotton - linen
···
high temperature
Fabric not to be ironed
Start ironing the garments requiring a low temperature.
This reduces the waiting times (the iron takes less time to heat up than to cool down)
and eliminates the risk of scorching the fabric.
STEAM IRONING
Filling the reservoir
- Check that the plug is disconnected from the socket.
- Move the steam selector (3) to “0”
[Fig. 1].
- Open the lid (2).
- Raise the tip of the iron to help the water enter the opening without overflowing.
- Slowly pour the water i
nto the reservoir using the special measure (18) and taking
care not to go over the maximum level indicated by “MAX” on the reservoir
[Fig.
2]
.
- Close the lid (2).
3
ANTI-CALC SYSTEM
A special resin filter inside the water reservoir softens the water and prevents scale
build-up in the plate. The resin filter is permanent and does not need replacing.
Please note:
Use tap water only. Distilled and/demineralised water makes the
“
Zero-Calc” anti-calc system ineffective by altering its physicochemical
characteristics.
Do not use chemical additives, scented substances or decalcifiers. Failure to
comply with the above-mentioned regulations leads to the loss of guarantee.
ANTI-DRIP SYSTEM
With the anti-drip system, you can perfectly iron even the most delicate fabrics.
Always iron these fabrics at low temperatures. The plate may cool down to the point
where no more steam comes out, but rather drops of
boiling water that can leave
marks or stains. In these cases, the Anti-drip system automatically activates to
prevent vaporization, so that you can iron the most delicate fabrics without risk of
spoiling or staining them.
AUTOMATIC SHUT OFF
The automatic shut off device trips after the iron has been left for approx. eight
minutes in the upright position or unused for approx. Thirty seconds in the horizontal
position. The light comes on to indicate that s
hut off has tripped. As soon as you
move the iron, the device turns off and the iron starts working again.
G E N E R A L I N S T R U C T I O N S
When using the iron for the first time, you may notice a slight emission of smoke
and hear some sounds made by the expanding plastics. This is quite normal and it
stops after a short time. We also recommend passing the iron over an ordinary cloth
before using it for the first time.
PREPARATIONS
Soft the laundry to be ironed according to the international symbols on the garment
label, or
if this is missing, according to the type of fabric.
GARMENT
LABEL
FABRIC
TYPE
THERMOSTAT
REGULATION
synthetic
·
low temperature
silk - wool
··
medium temperature
Cotton - linen
···
high temperature
Fabric not to be ironed
Start ironing the garments requiring a low temperature.
This reduces the waiting times (the iron takes less time to heat up than to cool down)
and eliminates the risk of scorching the fabric.
STEAM IRONING
Filling the reservoir
- Check that the plug is disconnected from the socket.
- Move the steam selector (3) to “0”
[Fig. 1].
- Open the lid (2).
- Raise the tip of the iron to help the water enter the opening without overflowing.
- Slowly pour the water i
nto the reservoir using the special measure (18) and taking
care not to go over the maximum level indicated by “MAX” on the reservoir
[Fig.
2]
.
- Close the lid (2).
3
ANTI-CALC SYSTEM
A special resin filter inside the water reservoir softens the water and prevents scale
build-up in the plate. The resin filter is permanent and does not need replacing.
Please note:
Use tap water only. Distilled and/demineralised water makes the
“
Zero-Calc” anti-calc system ineffective by altering its physicochemical
characteristics.
Do not use chemical additives, scented substances or decalcifiers. Failure to
comply with the above-mentioned regulations leads to the loss of guarantee.
ANTI-DRIP SYSTEM
With the anti-drip system, you can perfectly iron even the most delicate fabrics.
Always iron these fabrics at low temperatures. The plate may cool down to the point
where no more steam comes out, but rather drops of
boiling water that can leave
marks or stains. In these cases, the Anti-drip system automatically activates to
prevent vaporization, so that you can iron the most delicate fabrics without risk of
spoiling or staining them.
AUTOMATIC SHUT OFF
The automatic shut off device trips after the iron has been left for approx. eight
minutes in the upright position or unused for approx. Thirty seconds in the horizontal
position. The light comes on to indicate that s
hut off has tripped. As soon as you
move the iron, the device turns off and the iron starts working again.
G E N E R A L I N S T R U C T I O N S
When using the iron for the first time, you may notice a slight emission of smoke
and hear some sounds made by the expanding plastics. This is quite normal and it
stops after a short time. We also recommend passing the iron over an ordinary cloth
before using it for the first time.
PREPARATIONS
Soft the laundry to be ironed according to the international symbols on the garment
label, or
if this is missing, according to the type of fabric.
GARMENT
LABEL
FABRIC
TYPE
THERMOSTAT
REGULATION
synthetic
·
low temperature
silk - wool
··
medium temperature
Cotton - linen
···
high temperature
Fabric not to be ironed
Start ironing the garments requiring a low temperature.
This reduces the waiting times (the iron takes less time to heat up than to cool down)
and eliminates the risk of scorching the fabric.
STEAM IRONING
Filling the reservoir
- Check that the plug is disconnected from the socket.
- Move the steam selector (3) to “0”
[Fig. 1].
- Open the lid (2).
- Raise the tip of the iron to help the water enter the opening without overflowing.
- Slowly pour the water i
nto the reservoir using the special measure (18) and taking
care not to go over the maximum level indicated by “MAX” on the reservoir
[Fig.
2]
.
- Close the lid (2).
Содержание
- Anti calc system 4
- D e s c r i p t i o n o f d e v i c e 4
- Please note do not use chemical additive scented substances or decalcifiers failure to comply with the above mentioned regulations leads to the loss of guarantee 4
- Save these instructions 4
- Anti calc system 5
- D e s c r i p t i o n o f d e v i c e 5
- Please note do not use chemical additive scented substances or decalcifiers failure to comply with the above mentioned regulations leads to the loss of guarantee 5
- Save these instructions 5
- Anti calc system 7
- Anti drip system 7
- Automatic shut off 7
- G e n e r a l i n s t r u c t i o n s 7
- Please note use tap water only distilled and demineralised water makes the zero calc anti calc system ineffective by altering its physicochemical characteristics do not use chemical additives scented substances or decalcifiers failure to comply with the above mentioned regulations leads to the loss of guarantee 7
- Preparations 7
- Steam ironing filling the reservoir 7
- Advice for good ironing 10
- Anti calc system 14
- D e s c r i p t i o n o f d e v i c e 14
- Please note do not use chemical additive scented substances or decalcifiers failure to comply with the above mentioned regulations leads to the loss of guarantee 14
- Save these instructions 14
- Anti calc system 15
- D e s c r i p t i o n o f d e v i c e 15
- Please note do not use chemical additive scented substances or decalcifiers failure to comply with the above mentioned regulations leads to the loss of guarantee 15
- Save these instructions 15
- Anti calc system 17
- Anti drip system 17
- Automatic shut off 17
- G e n e r a l i n s t r u c t i o n s 17
- Please note use tap water only distilled and demineralised water makes the zero calc anti calc system ineffective by altering its physicochemical characteristics do not use chemical additives scented substances or decalcifiers failure to comply with the above mentioned regulations leads to the loss of guarantee 17
- Preparations 17
- Steam ironing filling the reservoir 17
- Advice for good ironing 20
- Anti calc system 24
- D e s c r i p t i o n o f d e v i c e 24
- Please note do not use chemical additive scented substances or decalcifiers failure to comply with the above mentioned regulations leads to the loss of guarantee 24
- Save these instructions 24
- Anti calc system 25
- Anti drip system 25
- Automatic shut off 25
- G e n e r a l i n s t r u c t i o n s 25
- Please note use tap water only distilled and demineralised water makes the zero calc anti calc system ineffective by altering its physicochemical characteristics do not use chemical additives scented substances or decalcifiers failure to comply with the above mentioned regulations leads to the loss of guarantee 25
- Preparations 25
- Steam ironing filling the reservoir 25
- Advice for good ironing 29
Похожие устройства
- Ardesto IR-C2230-BUR Инструкция по эксплуатации
- Ardesto IR-C2228-TQ Инструкция по эксплуатации
- Ardesto LSH-ZH1 Инструкция по эксплуатации
- Ardesto ACM-09CRN7 Инструкция по эксплуатации
- Ardesto ACM-09HRDN1 Инструкция по эксплуатации
- Ardesto ACM-11HRDN1 Инструкция по эксплуатации
- Ardesto ACM-18HRDN1 Инструкция по эксплуатации
- Ardesto ACM-24HRDN1 Инструкция по эксплуатации
- Ardesto FNT-R44X1W Инструкция по эксплуатации
- Ricoh WG-6 Инструкция по эксплуатации
- Ardesto FNT-R36X1W Инструкция по эксплуатации
- Ardesto FNM-X2G Инструкция по эксплуатации
- Ardesto FNM-X2S Инструкция по эксплуатации
- Ardesto FNM-X1W Инструкция по эксплуатации
- Ardesto FNM-X1B Инструкция по эксплуатации
- Ricoh SP 100SF Инструкция по эксплуатации
- Ardesto FN-R1608CB Инструкция по эксплуатации
- Ardesto FN-R1608RW Инструкция по эксплуатации
- Ardesto FN-1608RW Инструкция по эксплуатации
- Ardesto FN-1608CW Инструкция по эксплуатации