Bort BAS-48N-LT [6/41] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Bort BAS-48N-LT [6/41] English

Bort BAS-48N-Lt 93728236 [6/41] English
7
GB
Cordless screwdriver
TECHNICAL SPECIFICATIONS 1
PRODUCT ELEMENTS 2
1. On/off switch
2. Bit holder
3. Switch for changing direction of rotation
4. Ring for torque control
SAFETY
WARNING! Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, fi re
and/or serious injury.
• Recharge only with the charger specifi ed by the manu-
facturer. A charger that is suitable for one type of battery
pack may create a risk of fi re when used with another
battery pack.
• Use power tools only with specifi cally designated battery
packs. Use of any other battery packs may create a risk
of injury and fi re.
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the charger
(chargers with a rating of 230V or 240V can also be con-
nected to a 220V supply)
• In case of electrical or mechanical malfunction, imme-
diately switch off the tool or unplug charger from power
source
• SBM Group can assure fl awless functioning of the tool
only when original accessories are used
• Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
• This tool should not be used by people under the age of
16 years
• Be careful not to drill or drive into areas where electrical
wires may be contacted
• Do not touch the contacts in the charger
• Do not expose tool/charger/battery to rain
• Never charge battery outdoors
• Store tool/charger/battery in locations where tempera-
ture will not exceed 40° C or drop below 0° C
• Batteries will explode in fi re, so do not burn battery for
any reason
• When damaged, and under extreme usage and tem-
perature conditions, batteries may start to leak
- if liquid comes into contact with the skin, wash quickly
with soap and water, then with lemon juice or vinegar
- if liquid gets into the eyes, fl ush eyes with clean water for
a minimum of 10 minutes and seek immediately medical
attention
• When battery is not in tool or charger, it should be kept
away from metal objects such as nails, screws, keys etc.
to prevent short-circuit
• Do not use charger when damaged; take it to one of the
offi cially registered SBM Group Service Stations for a
safety check
• Do not use battery when damaged; it should be replaced
immediately
• Do not disassemble charger or battery
• Do not attempt to recharge non-rechargeable batteries
with the charger
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live)
wire in the cord of the charger to the earth terminal of
the plug
• If for any reason the old plug is cut off the cord of
the charger, it must be disposed of safely and not left
unattended
To ensure longer service life and proper per-
formance of the battery, take the following ac-
tions when you start using new battery:
1. Use the new battery, without recharging it, till its com-
plete discharge.
2. Then charge the battery for 3-5 hours.
3. Repeat abovementioned actions (1 and 2) 3-5 times to
reach the nominal battery capacity.
MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt.If the dirt does not come off use a soft
cloth moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please
contact your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of
the packaging materials can be recycled. Take these ma-
terials to the appropriate recycling locations. Take your
unwanted machines to your local SBM Group dealer.
Here they will be disposed of in an environmentally safe
way.
NiCd batteries can be recycled. Deliver them to a dispos-
al site for chemical waste so that they can be recycled or
disposed of in an environmentally friendly manner.
English

Содержание

Похожие устройства

Скачать