Timberk SWH FS4 30 H [15/16] Controller for fs5 fs6 lines
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Timberk SWH FS4 30 H [15/16] Controller for fs5 fs6 lines

Timberk SWH FS4 30 H [15/16] Controller for fs5 fs6 lines

Содержание

Похожие устройства

4 Preventive operations must be performed operation manual and safety precautions upon strict observance of the 5 The water heater is equipped with a thermal switch which cuts off power supply of the heating element upon water overheating or its absence in the water heater If the water heater is connected to the mains but water is not heated and the indicator doesn t light up then the thermal switch was switched off or not switched on To reset the water heater to the operating condition it is necessary to de energize the water heater remove the plate of the side lower cover for horizontal type vertical type water heater respectively for FS2 FS4 FS6 series horizontal type water heaters press the button located in the center of the thermal switch placed near the heating element with a round shape until it clicks Fig 15 for FS1 FS3 FS5 series vertical type water heaters unscrew retaining nut of the thermal switch fastened on the flange of the heating element turn the thermal switch and press the button located in the center of the thermal switch until it clicks Fig 16 if the button is not pressed and there is no clicking then you should wait until the thermal switch cools down to the initial temperature I II I I II I II I I II I II I II Hl II I II I II Hl II Q IMPORTANT If these actions had no positive result or the thermal switch turns off repeatedly during a short period of time then you should de energize the water heater cut off water supply and contact your local Timberk Authorized Service Center for a consult or repair of theappliance 9 PRECAUTIONS 1 Power outlet must be properly grounded The outlet must be designed for rated current not less than 10A Power outlet and plug must always remain dry to prevent current leakage Regularly check if the power plug is tightly connected to the outlet It must be done in the following order connect an electric plug into an outlet after half hour operation turn off the convector and disconnect the plug from the outlet check if the plug is heated by your hand If the plug heated over 50 C then replace the outlet by a new one to prevent damages incidents fire as a result of bad electric contact A specialist must do the job See also GFCI operation description FAILURE Heating indicator light doesn t light up water is not heated 3 The wall where the electric water heater is to be mounted must withstand at least the double weight of the water heater fully filled with water there must be no cracks and other damages on the wall Otherwise it is necessary to take measures to strengthen the mounting the hot water discharge cock 5 The drain pipe connected to the depressurization hole must be directed downward POSSIBLE CAUSES Contact a repairer TIMBERK sendee broken center 2 Temperature limiter was actuated or was not switched on Switch on the temperature switch following instructions on its activation papp 15 Contact a repairer TIMBERK service center 1 Water teed is cut off 1 Wait until water supply is restored 2 Water pressure is too low 2 Switch on the water heater again when 3 Water supply exhaust valve is closed Wncr temperature is too Water temperature control system is Contact a repairer TIMBERK service high damaged center Water leakage Seal at thepoint of pipe connection is broken Replace the joint seal Breaking ofthe internal tank corrosion Contact a repairer TIMBERK service Seal at thepoint ofthe heating element center Witcr flows from the Controller for FS5 FS6 lines TROUBLESHOOTING METHOD 1 Temperature adjustment device is normal water pressure restores 3 Open water supply exhaust valve appliance s case 4 The check relief valve supplied with the water heater must be installed on the water heater s cold water inlet pipe see Fig 1 2 3 4 11 WIRING DIAGRAM 3 Temperature limiter is broken Water doesn t flow from 2 In a place or on a wall where there is a possible water contact the power outlet installation height must be not less than 1 8 m Fig 17 connection is broken Heating indicator light lights up but water is not 1 Temperature adjustment device is broken 1 Contact a repairer TIMBERK service center 2 Insufficient time for heating 2 Wail until waler is heated heated 3 Heating element is broken 3 Contact a repairer TIMBERK service center 6 Since water temperature in the water heater can reach 75 C you shouldn t place your body parts under hot water upon the first activation To prevent burns adjust the outgoing water temperature properly 7 To drain water from the internal tank properly you need to use the drain hole only for FS2 FS4 FS6 series it is necessary to unscrew a plug covering the drain hole water can also be drained through a check relief valve unscrew the check relief valve drain knob screw and set the drain knob to the upper position at that hot water discharge cock must be open and cold water supply cock must be closed see Fig 14 Never drain water if its temperature is over 50 C since it may result in burns 8 If a flexible power cable is damaged then you must use power cables supplied by the manufacturer to replace it A qualified electrician must replace a power cable 28 www timberk ru storage water heater 10 TROUBLESHOOTING Table 3 Possible malfunctions and troubleshooting methods Error codes E1 no water inside the tank nevertheless the heating element is heated so called dry heating E2 power surge E3 current leakage E4 overheating NOTE Technical and any other characteristics of the appliance can be revised Such changes may be introduced without warning and prior notice to the consumers The manufacturer shall not be liable for changes in the appliance s wiring diagram that may be implemented without notice to the consumers www timberk ru storage water heater 29

Скачать