![Icom IC-F3GT [13/16] Other functions](/img/pdf.png)
Icom IC-F3GT [13/16] Other functions
![Icom IC-F4GT [13/16] Other functions](/views2/1074491/page13/bgd.png)
22
7
OTHER FUNCTIONS
21
6
SmarTrunk II
TM
OPERATION
DD
Clear channel alerting
*1
If all channels are busy, the transceiver automatically begins
searching for an open channel and beeps every ten seconds. When
two short beeps (low-pitched, then high-pitched) are heard, a chan-
nel is available. Push [M], [M] immediately to redial the last num-
ber.
DD
Emergency call
*2
Push [0], [M] to initiate an emergency call.
• Contact your Dealer for details.
DD
Placing a telephone call
*2
Enter the phone number followed by [1], [M].
• A high-pitched beep indicates that the number is accepted.
• When the called party answers, push the [PTT] switch to talk, and
release it to listen.
DD
Calling another local system subscriber
*2
Enter the subscriber number followed by [3], [M].
• A high-pitched beep indicates that the number is accepted.
• You hear ringing, then two short beeps when the subscriber an-
swers.
• If the other subscriber is on another call or out of range, you hear
a fast busy signal and the call terminates automatically.
*1: This function is available for the IC-F3GS/IC-F4GS when the
[Y]/[Z] keys are assigned the [M]/[ # ] key functions.
*2: This function is available for the IC-F3GT/GS,IC-F4GT/GS
only.
Use the Turbo SpeeDial function instead.
For additional operating instructions, contact your Dealer or
System Operator.
‘‘
DTMF PAGER/CODE SQUELCH
When you install optional the UT-108 DTMF DECODER UNIT into
the transceiver, DTMF pager function or code squelch function will
be available.
DD
DTMF pager
This function uses DTMF tones for calling and can be used as a
“common pager” to inform you that one of your group has called
even if the operator is temporarily away from the transceiver.
• When the connection code is received, a beep sounds, then “ ”
flashes and shows the called stations code number.
• Called stations code number are memorised automatically, and
are easy to re-call with “ID-MR select function”.
DD
Code squelch
This conveniently eliminates unwanted audio and is useful in group
activities or security related activities where unwanted output can
be a problem. The function is similar to a CTCSS tone squelch.
In order to use the above functions, cloning is necessary via a PC
using the optional CS-F3G cloning software. Using this software,
the transceiver’s model, individual RX Code CH, TX Code CH, Spe-
cial Tone Link2 (must be ‘E’) on 5Tone screen, 5Tone Signaling
Form on Memory-CH screen, Log, RX C-No, Key&Display, Com-
mon AutoReset TimerB, and other settings related to operation can
be set. Refer to the HELP file that comes with the CS-F3G
CLONING SOFTWARE for available settings.
Содержание
- 1 32 kamiminami hirano ku osaka 547 0003 japan 1
- A 5621d 1ex r printed in japan 1999 icom inc 1
- Count on us 1
- If3gt gs 1
- If4gt gs 1
- Instruction manual 1
- Uhf transceiver 1
- Vhf transceiver 1
- Avoid using or placing the transceiver in direct sunlight or in areas with temperatures below 14 f 10 c or above 122 f 50 c 2
- Do not modify the transceiver for any reason 2
- Do not push the ptt when not actually desiring to transmit 2
- Fcc caution changes or modifications to this transceiver not expressly approved by icom inc could void your authority to op erate this transceiver under fcc regulations 2
- Foreword 2
- Important 2
- Keep the transceiver from the heavy rain and never immerse it in the water the transceiver construction is water resistant not water proof 2
- R caution never hold the transceiver so that the antenna is very close to or touching exposed parts of the body especially the face or eyes while transmitting the transceiver will perform best if the microphone is 2 to 4 in 5 to 10 cm away from the lips and the transceiver is vertical 2
- R caution never operate the transceiver with a headset or other audio accessories at high volume levels 2
- R caution never short the terminals of the battery pack 2
- Save this instruction manual this instruction manual contains important operating instructions for the transceiver 2
- Table of contents 2
- Thank you for purchasing the ic f3gt gs ic f4gt gs fm trans ceiver read all instructions carefully and completely before using the transceiver 2
- The use of non icom battery packs chargers may impair transceiver performance and invalidate the warranty 2
- Panel description 3
- S1 red 3
- S2 black 3
- Speaker 3
- Switches controls keys and connectors 3
- Accessories 4
- Accessory attachment 4
- Function display 4
- Battery cautions 5
- Battery pack replacement 5
- Battery packs 5
- Battery charging 6
- Battery case option 7
- Charging note 7
- General 8
- Programmable functions 8
- Conventional operation 10
- Receiving and transmitting 10
- Call procedure 11
- D penalty timer once the time out timer is activated transmission is further inhibited for a period determined by the penalty timer 11
- D time out timer after continuous transmission for a pre programmed period the time out timer is activated causing the transceiver to stop transmit ting and automatically select receive 11
- Depending on programming you may be able to send 5 tone codes manually 11
- Manual 5 tone codes 11
- Push the tx code switch to activate the function then enter the de sired transmit code up to 7 digits using the keypad activate the call function to transmit the 5 tone code blinking indicates keypad entry is acceptable 11
- Q select the desired tx code channel or 5 tone code according to your system operator s instructions this may not be necessary depending on programming refer to the next page for selection w push the call switch assigned to one of the dealer programma ble switches p0 p1 p2 p3 s1 and s2 e after transmitting a 5 tone code the remainder of your commu nication can be carried out in the normal fashion 11
- The selected code channel containing a pre programmed 5 tone code is transmitted when using the call function 11
- Transmitting notes 11
- Tx code channel selection 11
- When your system employs tone signalling excluding ctcss and dtcs the call procedure may be necessary prior to voice trans mission the tone signalling employed may be a selective calling system which allows you to call specific station s only and prevent unwanted stations from contacting you 11
- Your radio may be programmed for tx code channel selection in this case you can choose a tx code channel to be transmitted when using the call function p 7 push the tx code channel switch assigned to one of the dealer programmable switches to activate the function then enter digits via the keypad to select the desired tx code channel 11
- Basic operation 12
- Operation 12
- Smartrunk i 12
- Dtmf pager code squelch 13
- Other functions 13
- Cloning 14
- Maintenance 14
- Note transceiver to transceiver cloning can not be done between 40ch version and 100ch version or cpu rev and rev 14
- Optional ut 96 ut 105 ut 108 ut 109 ut 110 ut 111 and ut 113 installation 14
- Option 15
- Options 15
Похожие устройства
- Ardo C 640G6 Инструкция по эксплуатации
- Icom IC-F4GT Инструкция по эксплуатации
- Ardo A 540 G6 Инструкция по эксплуатации
- Olympus TG-1 Silver Инструкция по эксплуатации
- Icom IC-F30GT Инструкция по эксплуатации
- Ardo PL 998 Инструкция по эксплуатации
- Icom IC-F40GT Инструкция по эксплуатации
- Ardo 66 GG40 VX Инструкция по эксплуатации
- Samsung ST77 Red Инструкция по эксплуатации
- Icom IC-F30LT Инструкция по эксплуатации
- Ardo 66 GG40 X Инструкция по эксплуатации
- Samsung ST77 Silver Инструкция по эксплуатации
- Icom IC-F40LT Инструкция по эксплуатации
- Ardo 66 GG40 W Инструкция по эксплуатации
- Sony SAL 1855 Инструкция по эксплуатации
- Icom IC-F33GT Инструкция по эксплуатации
- Ardo C 6640 G6 Инструкция по эксплуатации
- Sony SAL30 M28 Инструкция по эксплуатации
- Icom IC-F43GT Инструкция по эксплуатации
- Ardo A 56V4 ED Инструкция по эксплуатации