Icom IC-F4GT Инструкция по эксплуатации онлайн
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan
A-5621D-1EX-r
Printed in Japan
© 1999 Icom Inc.
Count on us!
IC-F3/4GS series
INSTRUCTION MANUAL
UHF TRANSCEIVER
iF4GT/GS
This device complies with Part 15 of the FCC rules. Oper-
ation is subject to the following two conditions: (1) This de-
vice may not cause harmful interference, and (2) this
device must accept any interference received, including in-
terference that may cause undesired operation.
iF3GT/GS
VHF TRANSCEIVER
2
3
4
5
6
789
0
1
P0
P1
P2 P3
Содержание
- 1 32 kamiminami hirano ku osaka 547 0003 japan 1
- A 5621d 1ex r printed in japan 1999 icom inc 1
- Count on us 1
- If3gt gs 1
- If4gt gs 1
- Instruction manual 1
- Uhf transceiver 1
- Vhf transceiver 1
- Avoid using or placing the transceiver in direct sunlight or in areas with temperatures below 14 f 10 c or above 122 f 50 c 2
- Do not modify the transceiver for any reason 2
- Do not push the ptt when not actually desiring to transmit 2
- Fcc caution changes or modifications to this transceiver not expressly approved by icom inc could void your authority to op erate this transceiver under fcc regulations 2
- Foreword 2
- Important 2
- Keep the transceiver from the heavy rain and never immerse it in the water the transceiver construction is water resistant not water proof 2
- R caution never hold the transceiver so that the antenna is very close to or touching exposed parts of the body especially the face or eyes while transmitting the transceiver will perform best if the microphone is 2 to 4 in 5 to 10 cm away from the lips and the transceiver is vertical 2
- R caution never operate the transceiver with a headset or other audio accessories at high volume levels 2
- R caution never short the terminals of the battery pack 2
- Save this instruction manual this instruction manual contains important operating instructions for the transceiver 2
- Table of contents 2
- Thank you for purchasing the ic f3gt gs ic f4gt gs fm trans ceiver read all instructions carefully and completely before using the transceiver 2
- The use of non icom battery packs chargers may impair transceiver performance and invalidate the warranty 2
- Panel description 3
- S1 red 3
- S2 black 3
- Speaker 3
- Switches controls keys and connectors 3
- Accessories 4
- Accessory attachment 4
- Function display 4
- Battery cautions 5
- Battery pack replacement 5
- Battery packs 5
- Battery charging 6
- Battery case option 7
- Charging note 7
- General 8
- Programmable functions 8
- Conventional operation 10
- Receiving and transmitting 10
- Call procedure 11
- D penalty timer once the time out timer is activated transmission is further inhibited for a period determined by the penalty timer 11
- D time out timer after continuous transmission for a pre programmed period the time out timer is activated causing the transceiver to stop transmit ting and automatically select receive 11
- Depending on programming you may be able to send 5 tone codes manually 11
- Manual 5 tone codes 11
- Push the tx code switch to activate the function then enter the de sired transmit code up to 7 digits using the keypad activate the call function to transmit the 5 tone code blinking indicates keypad entry is acceptable 11
- Q select the desired tx code channel or 5 tone code according to your system operator s instructions this may not be necessary depending on programming refer to the next page for selection w push the call switch assigned to one of the dealer programma ble switches p0 p1 p2 p3 s1 and s2 e after transmitting a 5 tone code the remainder of your commu nication can be carried out in the normal fashion 11
- The selected code channel containing a pre programmed 5 tone code is transmitted when using the call function 11
- Transmitting notes 11
- Tx code channel selection 11
- When your system employs tone signalling excluding ctcss and dtcs the call procedure may be necessary prior to voice trans mission the tone signalling employed may be a selective calling system which allows you to call specific station s only and prevent unwanted stations from contacting you 11
- Your radio may be programmed for tx code channel selection in this case you can choose a tx code channel to be transmitted when using the call function p 7 push the tx code channel switch assigned to one of the dealer programmable switches to activate the function then enter digits via the keypad to select the desired tx code channel 11
- Basic operation 12
- Operation 12
- Smartrunk i 12
- Dtmf pager code squelch 13
- Other functions 13
- Cloning 14
- Maintenance 14
- Note transceiver to transceiver cloning can not be done between 40ch version and 100ch version or cpu rev and rev 14
- Optional ut 96 ut 105 ut 108 ut 109 ut 110 ut 111 and ut 113 installation 14
- Option 15
- Options 15
Похожие устройства
- Ardo A 540 G6 Инструкция по эксплуатации
- Olympus TG-1 Silver Инструкция по эксплуатации
- Icom IC-F30GT Инструкция по эксплуатации
- Ardo PL 998 Инструкция по эксплуатации
- Icom IC-F40GT Инструкция по эксплуатации
- Ardo 66 GG40 VX Инструкция по эксплуатации
- Samsung ST77 Red Инструкция по эксплуатации
- Icom IC-F30LT Инструкция по эксплуатации
- Ardo 66 GG40 X Инструкция по эксплуатации
- Samsung ST77 Silver Инструкция по эксплуатации
- Icom IC-F40LT Инструкция по эксплуатации
- Ardo 66 GG40 W Инструкция по эксплуатации
- Sony SAL 1855 Инструкция по эксплуатации
- Icom IC-F33GT Инструкция по эксплуатации
- Ardo C 6640 G6 Инструкция по эксплуатации
- Sony SAL30 M28 Инструкция по эксплуатации
- Icom IC-F43GT Инструкция по эксплуатации
- Ardo A 56V4 ED Инструкция по эксплуатации
- Sony SAL35 F18 Инструкция по эксплуатации
- Icom IC-F121 Инструкция по эксплуатации