Sony CDX-G3300UV [20/164] For rds operation
![Sony CDX-G3300UV [20/164] For rds operation](/views2/1412767/page20/bg14.png)
20GB
For USB device playback:
HUB NO SUPRT: USB hubs are not
supported.
NOT SUPPORT ANDROID MODE
A USB device not supporting AOA
(Android Open Accessory) 2.0 is
connected to the unit while [USB MODE] is
set to [ANDROID].
– Set [USB MODE] to [MSC/MTP] (page 13).
USB ERROR
Connect the USB device again.
USB NO DEV
Make sure the USB device or USB cable is
securely connected.
USB NO MUSIC
Connect a USB device containing playable
files (page 16).
USB NO SUPRT
For details on the compatibility of your
USB device, visit the support site on the
back cover.
USB OVERLOAD: The USB device is
overloaded.
Disconnect the USB device, then press SRC
to select another source.
The USB device has a fault, or an
unsupported device is connected.
For RDS operation:
NO AF: No alternative frequencies.
Press / (SEEK –/+) while the
program service name is flashing. The unit
starts searching for another frequency
with the same PI (program identification)
data ([PI SEEK] appears).
NO PI: No program identification. The
selected station has no PI (program
identification) data.
Select another station.
NO TP: No traffic programs.
The unit will continue searching for
available TP stations.
For steering wheel remote control
operation:
ERROR
Register again from the function where
the error occurred (page 12).
TIMEOUT
Try completing the registration while
[REGISTER] is blinking (about 6 seconds)
(page 12).
For firmware update operation:
FILE ERROR: The updater is not stored in the
USB device.
Store the updater in the USB device, then
try again (page 15).
UPDATE ERROR PRESS ENTER: Firmware
update is not completed properly.
Press ENTER to clear the message, then try
again.
During the update, do not turn the
ignition to the OFF position, nor remove
the USB device (page 15).
If these solutions do not help improve the
situation, consult your nearest Sony dealer.
If you take the unit to be repaired because of
device playback trouble, bring the device
that was used at the time the problem
began.
Содержание
- 738 936 21 1 1
- Bedienungsanleitung de 1
- Cdx g1302u cdx g1301u cdx g1300u 1
- Fm mw lw cd car audio 1
- Fm mw lw cd автомобильное аудио 1
- Istruzioni per l uso it 1
- Manual de instrucciones 1
- Mode d emploi fr 1
- Operating instructions gb 1
- Инструкция по эксплуатации 1
- Caution 2
- Disposal of waste batteries and electrical and electronic equipment applicable in the european union and other countries with separate collection systems 2
- Notice for customers the following information is only applicable to equipment sold in countries applying eu directives 2
- Disclaimer regarding services offered by third parties 3
- Warning if your car s ignition has no acc position 3
- Additional information 4
- Connection installation 4
- Getting started 4
- Listening to the radio 4
- Playback 4
- Settings 4
- Table of contents 4
- Guide to parts and controls 5
- Main unit 5
- Attaching the front panel 7
- Detaching the front panel 7
- Getting started 7
- Resetting the unit 7
- Setting the area region 7
- Setting the clock 7
- Checking the battery voltage 8
- Connecting a usb device 8
- Connecting other portable audio device 8
- Listening to the radio 9
- Perform tuning 9
- Press menu rotate the control dial to select general then press it 9
- Press mode to change the band fm1 fm2 fm3 or mw lw 9
- Receiving the stored stations 9
- Rotate the control dial to select set af on set ta on set af ta on or set af ta off then press it 9
- Rotate the control dial to select set af ta then press it 9
- Rotate the control dial to select set btm then press it 9
- Select the band then press a number button 1 to 6 9
- Setting alternative frequencies af and traffic announcement ta 9
- Storing automatically btm 9
- Storing manually 9
- To adjust the volume level during a traffic announcement 9
- To receive emergency announcements 9
- To store rds stations with the af and ta setting 9
- Tuning 9
- Using radio data system rds 9
- While receiving the station that you want to store press and hold a number button 1 to 6 until mem appears 9
- Insert the disc label side up 10
- Local link function uk only 10
- Playback 10
- Playing a disc 10
- Playing a usb device 10
- Press pty during fm reception 10
- Rotate the control dial until the desired program type appears then press it 10
- Selecting program types pty 10
- To stay with one regional program regional 10
- Type of programs 10
- Repeat play and shuffle play 11
- Searching a track by name quick browzer 11
- Searching and playing tracks 11
- Searching by skipping items jump mode 11
- Basic setting operation 12
- Canceling the demo mode 12
- General setup general 12
- Press back twice 12
- Press menu 12
- Press menu rotate the control dial to select general then press it 12
- Rotate the control dial to select set demo off then press it 12
- Rotate the control dial to select set demo then press it 12
- Rotate the control dial to select the options then press it 12
- Rotate the control dial to select the setup category then press it 12
- Settings 12
- To return to the previous display 12
- Sound setup sound 13
- Display setup display 14
- Additional information 15
- Moisture condensation 15
- Notes on cd r cd rw discs 15
- Notes on discs 15
- Playback order of audio files 15
- Precautions 15
- Updating the firmware 15
- Cd player section 16
- Cleaning the connectors 16
- Maintenance 16
- Specifications 16
- Tuner section 16
- Usb player section 16
- Ask the dealer for detailed information 17
- Copyrights 17
- Corresponding codec mp3 mp3 bit rate 8 kbps 320 kbps supports vbr variable bit rate sampling rate 16 khz 48 khz wma wma bit rate 32 kbps 192 kbps supports vbr variable bit rate sampling rate 32 khz 44 khz 48 khz flac flac bit depth 16 bit 24 bit sampling rate 44 khz 48 khz supported file system fat16 fat32 17
- Design and specifications are subject to change without notice 17
- General 17
- In 2 in 7 in w h d mounting dimensions approx 182 mm 53 mm 159 mm 7 17
- In w h d mass approx 1 kg 2 lb 11 oz package contents main unit 1 parts for installation and connections 1 set 17
- Libflac 17
- Output speaker outputs speaker impedance 4 ω 8 ω maximum power output 55 w 4 at 4 ω 17
- Power amplifier section 17
- Power requirements 12 v dc car battery negative ground earth rated current consumption 10 a dimensions approx 178 mm 50 mm 176 mm 7 17
- General 18
- Radio reception 18
- Troubleshooting 18
- Cd playback 19
- For cd playback 19
- Messages 19
- Usb device playback 19
- For firmware update operation 20
- For rds operation 20
- For steering wheel remote control operation 20
- For usb device playback 20
- Cautions 21
- Connection installation 21
- Mounting angle adjustment 21
- Parts list for installation 21
- Precautions 21
- Connection 22
- Before connecting the speakers turn the unit off use speakers with an impedance of 4 ω to 8 ω and with adequate power handling capacities to avoid damage 23
- Check your car s auxiliary power connector and match the connections of leads correctly depending on the car 23
- If you have a power antenna aerial without a relay box connecting this unit with the supplied power supply lead may damage the antenna aerial 23
- Making connections 23
- Memory hold connection 23
- Power connection diagram 23
- Speaker connection 23
- Subwoofer easy connection 23
- To the car s power connector 23
- To the car s speaker connector 23
- When the yellow power supply lead is connected power will always be supplied to the memory circuit even when the ignition switch is turned off 23
- You can use a subwoofer without a power amplifier when it is connected to a rear speaker lead 23
- Installation 24
- Removing the protection collar and the bracket 24
- Using the wired remote control 24
- Detaching and attaching the front panel 25
- Fuse replacement 25
- Mount the unit onto the bracket then attach the protection collar 25
- Mounting the unit in the dashboard 25
- Position the bracket inside the dashboard then bend the claws outward for a tight fit 25
- Resetting the unit 25
- Entsorgung von gebrauchten batterien und akkus und gebrauchten elektrischen und elektronischen geräten anzuwenden in den ländern der europäischen union und anderen ländern mit einem separaten sammelsystem für diese produkte 26
- Hinweis für kunden die folgenden informationen gelten nur für geräte die in ländern verkauft werden in denen eu richtlinien gelten 26
- Achtung 27
- Haftungsausschluss für von dritten angebotene dienste 27
- Warnhinweis wenn die zündung ihres fahrzeugs nicht über eine zubehörposition acc oder i verfügt 27
- Anschluss installation 28
- Einstellungen 28
- Inhalt 28
- Radioempfang 28
- Vorbereitungen 28
- Weitere informationen 28
- Wiedergabe 28
- Hauptgerät 29
- Lage und funktion der teile und bedienelemente 29
- Abnehmen der frontplatte 31
- Anbringen der frontplatte 31
- Drehen sie den steuerregler um europe oder russia auszuwählen und drücken sie anschließend den steuerregler 31
- Drehen sie den steuerregler um yes oder no auszuwählen und drücken sie anschließend den steuerregler 31
- Drücken sie dspl und eq länger als 2 sekunden 31
- Drücken sie enter solange set area angezeigt wird 31
- Einstellen des landes bzw der region 31
- Halten sie off gedrückt bis sich das gerät ausschaltet drücken sie die taste zum lösen der frontplatte und ziehen sie die frontplatte auf sich zu und heraus 31
- Vorbereitungen 31
- Warnton 31
- Zurücksetzen des geräts 31
- Anschließen eines usb geräts 32
- Einstellen der uhr 32
- Überprüfen der batteriespannung 32
- Anschließen eines anderen tragbaren audiogeräts 33
- Automatisches speichern von sendern btm 33
- Drehen sie den steuerregler um set btm auszuwählen und drücken sie anschließend den steuerregler 33
- Drehen sie die lautstärke an diesem gerät herunter 33
- Drücken sie menu drehen sie den steuerregler um general auszuwählen und drücken sie anschließend den steuerregler 33
- Drücken sie mode um den frequenzbereich zu wechseln fm1 fm2 fm3 oder mw lw 33
- Drücken sie src und wählen sie aux aus 33
- Radioempfang 33
- Schalten sie das tragbare audiogerät aus 33
- Schließen sie das tragbare audiogerät mit einem verbindungskabel nicht mitgeliefert an die aux eingangsbuchse stereominibuchse am gerät an 33
- Sendereinstellung 33
- So gleichen sie den lautstärkepegel des angeschlossenen geräts an andere tonquellen an 33
- Stellen sie sender ein 33
- Das radiodatensystem rds 34
- Drehen sie den steuerregler um set af on set ta on set af ta on oder set af ta off auszuwählen und drücken sie anschließend den steuerregler 34
- Drehen sie den steuerregler um set af ta auszuwählen und drücken sie anschließend den steuerregler 34
- Drücken sie menu drehen sie den steuerregler um general auszuwählen und drücken sie anschließend den steuerregler 34
- Einstellen gespeicherter sender 34
- Einstellen von alternativfrequenzen af und verkehrsdurchsagen ta 34
- Lokalsenderfunktion nur großbritannien 34
- Manuelles speichern von sendern 34
- So empfangen sie katastrophenwarnungen 34
- So speichern sie rds sender zusammen mit der af und ta einstellung 34
- So stellen sie während einer verkehrsdurchsage die lautstärke ein 34
- Unveränderter empfang eines regionalsenders regional 34
- Wählen sie den frequenzbereich aus und drücken sie eine stationstaste 1 bis 6 34
- Während des empfangs des zu speichernden senders halten sie eine stationstaste 1 bis 6 so lange gedrückt bis mem angezeigt wird 34
- Auswählen des programmtyps pty 35
- Drehen sie den steuerregler bis der gewünschte programmtyp angezeigt wird und drücken sie anschließend den steuerregler 35
- Drücken sie pty während des empfangs eines ukw senders fm 35
- Legen sie eine cd mit der beschrifteten seite nach oben ein 35
- Programmtypen 35
- Wiedergabe 35
- Wiedergabe mit einem usb gerät 35
- Wiedergeben von discs 35
- Suchen mit überspringen von elementen sprung modus 36
- Suchen nach einem titel anhand seines namens quick browzer 36
- Suchen und wiedergeben von titeln 36
- Wiedergabewiederholung und zufallswiedergabe 36
- Beenden des demo modus 37
- Einstellungen 37
- Grundlegende einstellschritte 37
- Allgemeine einstellungen general 38
- So schalten sie zur vorherigen anzeige zurück 38
- Klangeinstellungen sound 39
- Anzeigeeinstellungen display 40
- Aktualisieren der firmware 41
- Feuchtigkeitskondensation 41
- Hinweise zu cd rs cd rws 41
- Hinweise zu discs 41
- Sicherheitsmaßnahmen 41
- Weitere informationen 41
- Cd player 42
- Reinigen der anschlüsse 42
- Technische daten 42
- Usb player 42
- Wartung 42
- Wiedergabereihenfolge von audiodateien 42
- Allgemeines 43
- Ausgänge lautsprecherausgänge lautsprecherimpedanz 4 ω 8 ω maximale ausgangsleistung 55 w 4 an 4 ω 43
- Betriebsspannung 12 v gleichstrom autobatterie negative erdung nennstromaufnahme 10 a abmessungen ca 178 mm 50 mm 176 mm b h t einbaumaße ca 182 mm 53 mm 159 mm b h t gewicht ca 1 2 kg lieferumfang hauptgerät 1 montageteile und anschlusszubehör 1 satz 43
- Endverstärker 43
- Entsprechender codec mp3 mp3 bitrate 8 kbps 320 kbps unterstützt vbr variable bitrate abtastrate 16 khz 48 khz wma wma bitrate 32 kbps 192 kbps unterstützt vbr variable bitrate abtastrate 32 khz 44 1 khz 48 khz flac flac bittiefe 16 bit 24 bit abtastrate 44 1 khz 48 khz unterstütztes dateisystem fat16 fat32 43
- Libflac 43
- Nähere informationen dazu erhalten sie beim händler 43
- Urheberrechte 43
- Änderungen die dem technischen fortschritt dienen bleiben vorbehalten 43
- Allgemeines 44
- Radioempfang 44
- Störungsbehebung 44
- Cd wiedergabe 45
- Wiedergabe mit einem usb gerät 45
- Bei der cd wiedergabe 46
- Bei der wiedergabe mit einem usb gerät 46
- Meldungen 46
- Beim aktualisieren der firmware 47
- Beim rds betrieb 47
- Beim verwenden der lenkradfernbedienung 47
- Anschluss installation 48
- Einstellen des montagewinkels 48
- Sicherheitsmaßnahmen 48
- Teileliste für die installation 48
- Vorsichtsmaßnahmen 48
- Anschluss 49
- An den lautsprecheranschluss des fahrzeugs 50
- An den stromanschluss des fahrzeugs 50
- Anschluss für stromversorgung des speichers 50
- Einfaches anschließen eines tiefsttonlautsprechers 50
- Hecklautsprecher links 50
- Hecklautsprecher rechts 50
- Lautsprecheranschluss 50
- Schalten sie das gerät vor dem anschließen der lautsprecher aus verwenden sie lautsprecher mit einer impedanz zwischen 4 ω und 8 ω und mit ausreichender belastbarkeit um schäden zu vermeiden 50
- Sie können einen tiefsttonlautsprecher ohne endverstärker installieren indem sie ihn einfach an ein hecklautsprecherkabel anschließen 50
- Stellen sie die position des hilfsstromanschlusses bei ihrem fahrzeug fest und nehmen sie die anschlüsse entsprechend dem fahrzeug richtig vor 50
- Stromanschlussdiagramm 50
- Vornehmen der anschlüsse 50
- Wenn die gelbe stromversorgungsleitung angeschlossen ist wird der speicher stets auch bei ausgeschalteter zündung mit strom versorgt 50
- Wenn sie eine motorantenne ohne relaiskästchen verwenden und dieses gerät mit der mitgelieferten stromversorgungsleitung anschließen kann die antenne beschädigt werden 50
- Abnehmen der schutzumrandung und der halterung 51
- Installation 51
- Verwenden der kabelfernbedienung 51
- Abnehmen und anbringen der frontplatte 52
- Austauschen der sicherung 52
- Montieren des geräts im armaturenbrett 52
- Montieren sie das gerät an der halterung und bringen sie dann die schutzumrandung an 52
- Platzieren sie die halterung im armaturenbrett und biegen sie dann die klammern nach außen um einen sicheren halt zu gewährleisten 52
- Zurücksetzen des geräts 52
- Avis à l attention des clients les informations suivantes s appliquent uniquement aux appareils vendus dans des pays qui appliquent les directives de l union européenne 54
- Elimination des piles et accumulateurs et des équipements électriques et électroniques usagés applicable dans les pays de l union européenne et dans les autres pays disposant de systèmes de collecte sélective 54
- Attention 55
- Avertissement au cas où le contact de votre voiture ne dispose pas d une position acc 55
- Avis d exclusion de responsabilité relatif aux services proposés par des tiers 55
- Informations complémentaires 56
- Lecture 56
- Préparation 56
- Raccordement installation 56
- Réglages 56
- Table des matières 56
- Utilisation de la radio 56
- Appareil principal 57
- Emplacement des commandes 57
- Installation de la façade avant 59
- Préparation 59
- Retrait de la façade avant 59
- Réglage de l horloge 59
- Réglage de la zone région 59
- Réinitialisation de l appareil 59
- Connexion d un autre périphérique audio portatif 60
- Connexion d un périphérique usb 60
- Contrôle de la tension de la batterie 60
- Appuyez sur menu tournez la molette de réglage pour sélectionner general puis appuyez dessus 61
- Appuyez sur mode pour changer de bande fm1 fm2 fm3 ou mw po lw go 61
- Lorsque vous recevez la station que vous souhaitez mémoriser appuyez sur une touche numérique 1 à 6 et maintenez la enfoncée jusqu à ce que mem apparaisse 61
- Mémorisation automatique btm 61
- Mémorisation manuelle 61
- Procédez à la syntonisation 61
- Réception des stations mémorisées 61
- Réglage des fonctions af fréquences alternatives et ta messages de radioguidage 61
- Syntonisation 61
- Sélectionnez la bande puis appuyez sur une touche numérique 1 à 6 61
- Tournez la molette de réglage pour sélectionner set af on set ta on set af ta on ou set af ta off puis appuyez dessus 61
- Tournez la molette de réglage pour sélectionner set af ta puis appuyez dessus 61
- Tournez la molette de réglage pour sélectionner set btm puis appuyez dessus 61
- Utilisation de la radio 61
- Utilisation du système rds système de radiocommunication de données 61
- Cette fonction vous permet de sélectionner d autres stations locales de la région même si elles ne sont pas associées à vos touches numériques en cours de réception fm appuyez sur une touche numérique 1 à 6 sur laquelle une station locale est mémorisée dans les 5 secondes qui suivent appuyez de nouveau sur la touche numérique de la station locale répétez cette procédure jusqu à ce que vous captiez la station locale souhaitée 62
- En cours de réception fm appuyez sur pty 62
- Fonction de liaison locale royaume uni uniquement 62
- L appareil commence à rechercher une station diffusant le type d émission sélectionné 62
- Le niveau sera enregistré dans la mémoire pour les messages de radioguidage ultérieurs indépendamment du niveau de volume normal 62
- Lorsque la fonction af ou ta est activée les messages d urgence interrompent automatiquement la source sélectionnée en cours de diffusion 62
- Lorsque les fonctions af et regional sont activées vous ne basculez pas sur une autre station régionale ayant une fréquence plus puissante si vous quittez la zone de réception de cette émission régionale réglez set regional dans general sur set reg off en cours de réception fm page 14 cette fonction est inopérante au royaume uni et dans certaines autres régions 62
- Mémorisation des stations rds avec les réglages af et ta 62
- Réception de messages d urgence 62
- Réglage du niveau de volume pendant la diffusion d un message de radioguidage 62
- Sélection de types d émission pty 62
- Tournez la molette de réglage jusqu à ce que le type d émission souhaité apparaisse puis appuyez dessus 62
- Types d émissions 62
- Vous pouvez présélectionner les stations rds avec un réglage af ta réglez af ta puis mémorisez la station à l aide de la fonction btm ou manuellement si vous effectuez une présélection manuelle vous pouvez également présélectionner des stations non rds 62
- Écoute continue d une émission régionale regional 62
- Insérez le disque étiquette vers le haut 63
- Lecture 63
- Lecture d un disque 63
- Lecture d un périphérique usb 63
- Pour arrêter la lecture 63
- Pour retirer le périphérique 63
- Raccordez un périphérique usb au port usb page 8 63
- Réglez le volume sur cet appareil 63
- Lecture répétée et aléatoire 64
- Recherche d une plage par son nom quick browzer 64
- Recherche d éléments par saut mode saut 64
- Recherche et lecture de plages 64
- Appuyez deux fois sur retour 65
- Appuyez sur menu 65
- Appuyez sur menu tournez la molette de réglage pour sélectionner general puis appuyez dessus 65
- Configuration générale general 65
- Désactivation du mode demo 65
- Pour revenir à l affichage précédent 65
- Réglages 65
- Réglages de base 65
- Tournez la molette de réglage pour sélectionner la catégorie de configuration puis appuyez dessus 65
- Tournez la molette de réglage pour sélectionner les options puis appuyez dessus 65
- Tournez la molette de réglage pour sélectionner set demo off puis appuyez dessus 65
- Tournez la molette de réglage pour sélectionner set demo puis appuyez dessus 65
- Configuration du son sound 67
- Condensation 68
- Configuration de l affichage display 68
- Informations complémentaires 68
- Mise à jour du firmware 68
- Précautions 68
- Remarques sur les disques 68
- Entretien 69
- Nettoyage des connecteurs 69
- Ordre de lecture des fichiers audio 69
- Remarques sur les disques cd r cd rw 69
- Amplificateur de puissance 70
- Généralités 70
- Lecteur cd 70
- Lecteur usb 70
- Spécifications 70
- Copyrights 71
- Dépannage 71
- Généralités 71
- Lecture de cd 72
- Réception radio 72
- Lecture de périphériques usb 73
- Messages 73
- Pour la lecture de cd 73
- Pour la lecture de périphériques usb 73
- Pour la transmission rds 74
- Pour le fonctionnement de la mise à jour du firmware 74
- Pour utiliser la télécommande au volant 74
- Attention 75
- Liste des pièces pour installation 75
- Précautions 75
- Raccordement installation 75
- Réglage de l angle de fixation 75
- Raccordement 76
- Avant de raccorder les haut parleurs mettez l appareil hors tension utilisez des haut parleurs dont l impédance est comprise entre 4 ω et 8 ω et dont la puissance admissible est appropriée pour éviter qu ils soient endommagés 77
- Connexion aisée d un caisson de graves 77
- Lorsque le câble d alimentation jaune est raccordé le circuit mémoire est toujours alimenté même lorsque le contact est coupé 77
- Raccordement de protection de la mémoire 77
- Raccordement des haut parleurs 77
- Raccordements 77
- Schéma de raccordement électrique 77
- Si vous disposez d une antenne électrique dépourvue de relais vous risquez de l endommager si vous raccordez cet appareil à l aide du câble d alimentation fourni 77
- Vers le connecteur d alimentation du véhicule 77
- Vers le connecteur des haut parleurs du véhicule 77
- Vous pouvez utiliser un caisson de graves sans amplificateur de puissance pour autant qu il soit raccordé à un fil de haut parleur arrière 77
- Vérifiez le connecteur d alimentation auxiliaire de votre véhicule et faites correspondre correctement les raccordements en fonction du véhicule 77
- Installation 78
- Retrait du tour de protection et du support 78
- Utilisation de la télécommande filaire 78
- Montage de l appareil dans le tableau de bord 79
- Montez l appareil sur le support puis fixez le tour de protection 79
- Positionnez le support à l intérieur du tableau de bord puis pliez les griffes vers l extérieur pour un ajustement serré 79
- Remplacement du fusible 79
- Retrait et fixation de la façade avant 79
- Réinitialisation de l appareil 79
- Avviso per i clienti le seguenti informazioni riguardano esclusivamente gli apparecchi venduti in paesi in cui sono applicate le direttive ue 80
- Smaltimento delle batterie pile e accumulatori esauste e delle apparecchiature elettriche ed elettroniche a fine vita applicabile in tutti i paesi dell unione europea e negli altri paesi con sistema di raccolta differenziata 80
- Attenzione 81
- Avvertenza relativa all installazione su un auto sprovvista della posizione acc accessoria sul blocchetto di accensione 81
- Dichiarazione di non responsabilità relativa a servizi offerti da terze parti 81
- Ascolto della radio 82
- Collegamenti e installazione 82
- Impostazioni 82
- Indice 82
- Informazioni aggiuntive 82
- Operazioni preliminari 82
- Riproduzione 82
- Guida alle parti e ai comandi 83
- Unità principale 83
- Azzeramento dell apparecchio 85
- Impostazione dell area regione 85
- Installazione del pannello anteriore 85
- Operazioni preliminari 85
- Premere dspl ed eq per più di 2 secondi 85
- Premere enter mentre è visualizzato set area 85
- Rimozione del pannello anteriore 85
- Ruotare la manopola di controllo per selezionare europe o russia quindi premere la manopola 85
- Ruotare la manopola di controllo per selezionare yes o no quindi premere la manopola 85
- Segnale di avvertimento 85
- Tenere premuto off fino allo spegnimento dell apparecchio quindi premere il tasto rilascio pannello anteriore infine tirare il pannello verso di sé per estrarlo 85
- Collegamento di un altro dispositivo audio portatile 86
- Collegamento di un dispositivo usb 86
- Controllo della tensione della batteria 86
- Impostazione dell orologio 86
- Ascolto della radio 87
- Durante la ricezione della stazione che si desidera memorizzare tenere premuto un tasto numerico da 1 a 6 fino a visualizzare mem 87
- Eseguire la sintonizzazione 87
- Impostazione delle funzioni af frequenze alternative e ta notiziari sul traffico 87
- Memorizzazione automatica btm 87
- Memorizzazione di stazioni rds con impostazione af e ta 87
- Memorizzazione manuale 87
- Premere menu ruotare la manopola di controllo per selezionare general quindi premere la manopola 87
- Premere mode per cambiare banda fm1 fm2 fm3 o mw lw 87
- Ricezione dei notiziari di emergenza 87
- Ricezione delle stazioni memorizzate 87
- Ruotare la manopola di controllo per selezionare set af on set ta on set af ta on o set af ta off quindi premere la manopola 87
- Ruotare la manopola di controllo per selezionare set af ta quindi premere la manopola 87
- Ruotare la manopola di controllo per selezionare set btm quindi premere la manopola 87
- Selezionare la banda quindi premere un tasto numerico da 1 a 6 87
- Sintonizzazione 87
- Utilizzo del sistema rds sistema dati radio 87
- Funzione local link solo per il regno unito 88
- Il livello del volume viene memorizzato anche per i notiziari sul traffico successivi indipendentemente dal normale livello del volume 88
- L apparecchio avvia la ricerca di una stazione che trasmette il tipo di programma selezionato 88
- Mantenimento del programma regionale regional 88
- Premere pty durante la ricezione fm 88
- Quando sono attivate le funzioni af e regional la stazione sintonizzata non verrà sostituita da un altra stazione regionale con segnale più potente se si intende lasciare tale area di ricezione regionale impostare set regional in general su set reg off durante la ricezione fm pagina 14 questa funzione non è disponibile nel regno unito e in altre aree 88
- Questa funzione consente di selezionare altre stazioni locali della stessa area anche se non sono memorizzate in corrispondenza dei tasti numerici durante la ricezione fm premere un tasto numerico da 1 a 6 in corrispondenza del quale è memorizzata una stazione locale entro 5 secondi premere nuovamente il tasto numerico della stazione locale ripetere questa procedura fino alla ricezione della stazione locale 88
- Regolazione del livello del volume durante la ricezione di un notiziario sul traffico 88
- Ruotare la manopola di controllo fino a visualizzare il tipo di programma desiderato quindi premere la manopola 88
- Selezione del modo pty tipo di programma 88
- Tipi di programmi 88
- Collegare un dispositivo usb alla porta usb pagina 8 89
- Durante la riproduzione premere più volte ripeti o ordine casuale per selezionare il modo di riproduzione desiderato 89
- Inserire il disco lato con l etichetta rivolto verso l alto 89
- Per interrompere la riproduzione 89
- Per rimuovere il dispositivo 89
- Regolare il volume sul presente apparecchio 89
- Ricerca e riproduzione dei brani 89
- Riproduzione 89
- Riproduzione di un disco 89
- Riproduzione di un dispositivo usb 89
- Riproduzione ripetuta e in ordine casuale 89
- Disattivazione del modo demo 90
- Impostazioni 90
- Operazioni di base delle impostazioni 90
- Ricerca di un brano in base al nome quick browzer 90
- Ricerca mediante la modalità salto delle voci modo jump 90
- Impostazione generale general 91
- Per tornare al display precedente 91
- Impostazione dell audio sound 92
- Impostazione del display display 93
- Aggiornamento del firmware 94
- Formazione di condensa 94
- Informazioni aggiuntive 94
- Note sui dischi 94
- Note sui dischi cd r cd rw 94
- Precauzioni 94
- Caratteristiche tecniche 95
- Lettore cd 95
- Lettore usb 95
- Manutenzione 95
- Ordine di riproduzione dei file audio 95
- Pulizia dei connettori 95
- Sintonizzatore 95
- Amplificatore di potenza 96
- Codec corrispondenti mp3 mp3 velocità di trasmissione 8 kbps 320 kbps supporta vbr variable bit rate velocità di trasmissione variabile frequenza di campionamento 16 khz 48 khz wma wma velocità di trasmissione 32 kbps 192 kbps supporta vbr variable bit rate velocità di trasmissione variabile frequenza di campionamento 32 khz 44 1 khz 48 khz flac flac profondità in bit 16 bit 24 bit frequenza di campionamento 44 1 khz 48 khz file system supportati fat16 fat32 96
- Generali 96
- Il design e le caratteristiche tecniche sono soggetti a modifiche senza preavviso 96
- Informazioni su copyright 96
- Libflac 96
- Per ulteriori informazioni rivolgersi al rivenditore 96
- Requisiti di alimentazione batteria auto da 12 v cc massa negativa consumo di corrente nominale 10 a dimensioni circa 178 mm 50 mm 176 mm l a p dimensioni di montaggio circa 182 mm 53 mm 159 mm l a p peso circa 1 2 kg contenuto della confezione unità principale 1 elementi per l installazione e i collegamenti 1 set 96
- Uscita uscite diffusori impedenza diffusori 4 ω 8 ω potenza di uscita massima 55 w 4 a 4 ω 96
- Generali 97
- Guida alla soluzione dei problemi 97
- Ricezione radiofonica 97
- Messaggi 98
- Riproduzione di cd 98
- Riproduzione mediante un dispositivo usb 98
- Funzionamento del telecomando da volante 99
- Funzionamento rds 99
- Riproduzione di cd 99
- Riproduzione mediante un dispositivo usb 99
- Per l aggiornamento del firmware 100
- Attenzione 101
- Collegamenti e installazione 101
- Elenco dei componenti per l installazione 101
- Precauzioni 101
- Regolazione dell angolo di montaggio 101
- Connessioni 102
- Al connettore del diffusore dell auto 103
- Al connettore di alimentazione dell auto 103
- Collegamenti 103
- Collegamento dei diffusori 103
- Collegamento per la conservazione della memoria 103
- Collegamento semplice del subwoofer 103
- Controllare il connettore di alimentazione ausiliaria dell automobile e far corrispondere correttamente i collegamenti dei cavi a seconda dell automobile 103
- Diagramma dei collegamenti di alimentazione 103
- Prima di collegare i diffusori spegnere l apparecchio usare diffusori di impedenza compresa tra 4 ω e 8 ω e con capacità di potenza adeguata altrimenti i diffusori potrebbero essere danneggiati 103
- Quando il cavo di ingresso alimentazione giallo è collegato viene sempre fornita alimentazione al circuito di memoria anche quando l interruttore di accensione è spento 103
- Quando si collega l apparecchio con il cavo di alimentazione in dotazione si potrebbe danneggiare l antenna elettrica se questa non dispone di scatola a relè 103
- È possibile utilizzare un subwoofer senza un amplificatore di potenza quando è collegato a un cavo del diffusore posteriore 103
- Installazione 104
- Rimozione della staffa e della cornice protettiva 104
- Uso del telecomando cablato 104
- Azzeramento dell apparecchio 105
- Inserire la staffa nel cruscotto quindi piegare verso l esterno i morsetti per un installazione sicura 105
- Montaggio dell apparecchio sul cruscotto 105
- Montare l apparecchio sulla staffa quindi fissare la cornice protettiva 105
- Rimozione e installazione del pannello anteriore 105
- Sostituzione del fusibile 105
- Aviso para los clientes la información siguiente resulta de aplicación solo a los equipos comercializados en países afectados por las directivas de la ue 106
- Tratamiento de las baterías y equipos eléctricos y electrónicos al final de su vida útil aplicable en la unión europea y otros países con sistemas de tratamiento selectivo de residuos 106
- Advertencia si el encendido del automóvil no dispone de una posición acc 107
- Nota legal acerca de los servicios prestados por otros proveedores 107
- Precaución 107
- Ajustes 108
- Conexión instalación 108
- Escuchar la radio 108
- Información adicional 108
- Procedimientos iniciales 108
- Reproducción 108
- Tabla de contenidos 108
- Guía de elementos y controles 109
- Unidad principal 109
- Ajuste de la región 111
- Ajuste del reloj 111
- Extracción del panel frontal 111
- Montaje del panel frontal 111
- Procedimientos iniciales 111
- Reinicio de la unidad 111
- Comprobación de la tensión de la batería 112
- Conexión de otros dispositivos de audio vídeo portátiles 112
- Conexión de un dispositivo usb 112
- Ajuste de frecuencias alternativas af y anuncios de tráfico ta 113
- Almacenamiento automático btm 113
- Almacenamiento manual 113
- Efectúe la sintonización 113
- Escuchar la radio 113
- Gire el dial de control para seleccionar set af on set ta on set af ta on o set af ta off y a continuación púlselo 113
- Gire el dial de control para seleccionar set af ta y púlselo 113
- Gire el dial de control para seleccionar set btm y púlselo 113
- Mientras recibe la emisora que desea almacenar mantenga pulsado un botón numérico 1 a 6 hasta que aparezca mem 113
- Para almacenar emisoras de rds con ajuste de af y ta 113
- Para recibir anuncios de emergencia 113
- Pulse menu gire el dial de control para seleccionar general y a continuación púlselo 113
- Pulse mode para cambiar de banda fm1 fm2 fm3 o mw lw 113
- Recepción de emisoras almacenadas 113
- Seleccione la banda y a continuación toque el número de presintonía deseado 1 a 6 113
- Sintonización 113
- Utilización del sistema de datos de radio rds 113
- Durante la recepción de fm pulse pty 114
- El nivel se almacenará en la memoria para futuros anuncios de tráfico independientemente del nivel de volumen regular 114
- Esta función permite seleccionar otras emisoras locales de la zona aunque no estén almacenadas en sus botones numéricos durante la recepción fm pulse un botón numérico 1 a 6 en el que haya una emisora local almacenada antes de que transcurran 5 segundos vuelva a pulsar un botón numérico de una emisora local repita este procedimiento hasta que reciba la emisora local 114
- Función local link solo reino unido 114
- Gire el dial de control hasta que aparezca el tipo de programa que desee y a continuación púlselo 114
- La unidad busca emisoras que ofrezcan el tipo de programa seleccionado 114
- Para ajustar el nivel de volumen durante un anuncio de tráfico 114
- Para continuar recibiendo un programa regional regional 114
- Selección de tipos de programa pty 114
- Si las funciones af y regional están activadas no se cambiará a otra emisora regional con una frecuencia más intensa si abandona la zona de recepción de dicho programa regional ajuste set regional de general en set reg off durante la recepción de fm página 14 esta función no está disponible en el reino unido ni en algunas otras zonas 114
- Tipos de programas 114
- Ajuste el volumen en esta unidad 115
- Búsqueda y reproducción de pistas 115
- Conecte el dispositivo usb al puerto usb página 8 115
- Durante la reproducción pulse varias veces repetición o aleatorio para seleccionar el modo de reproducción que desee 115
- Inserte el disco etiqueta hacia arriba 115
- Para detener la reproducción 115
- Para expulsar el dispositivo 115
- Reproducción 115
- Reproducción aleatoria y repetición 115
- Reproducción de un disco 115
- Reproducción de un dispositivo usb 115
- Ajustes 116
- Búsqueda de pista por nombre quick browzer 116
- Búsqueda omitiendo elementos modo salto 116
- Cancelación del modo demo 116
- Funcionamiento de los ajustes básicos 116
- Ajustes generales general 117
- Ajustes de sonido sound 118
- Ajustes de pantalla display 119
- Actualización del firmware 120
- Condensación de humedad 120
- Información adicional 120
- Notas sobre los discos 120
- Notas sobre los discos cd r cd rw 120
- Precauciones 120
- Especificaciones 121
- Limpieza de los conectores 121
- Mantenimiento 121
- Orden de reproducción de archivos de audio 121
- Sección del reproductor de cd 121
- Sección del reproductor usb 121
- Sección del sintonizador 121
- Códec correspondiente mp3 mp3 velocidad de bits 8 kbps 320 kbps compatible con vbr velocidad de bits variable frecuencia de muestreo 16 khz 48 khz wma wma velocidad de bits 32 kbps 192 kbps compatible con vbr velocidad de bits variable frecuencia de muestreo 32 khz 44 1 khz 48 khz flac flac profundidad de bits 16 bits 24 bits frecuencia de muestreo 44 1 khz 48 khz sistema de archivos compatible fat16 fat32 122
- Derechos de autor 122
- El diseño y las especificaciones pueden variar sin previo aviso 122
- General 122
- Libflac 122
- Para obtener más información consulte al distribuidor 122
- Requisitos de alimentación batería para vehículo de 12 v cc masa negativa consumo de corriente nominal 10 a dimensiones aprox 178 mm 50 mm 176 mm an al pr dimensiones de montaje aprox 182 mm 53 mm 159 mm an al pr peso aprox 1 2 kg contenidos del paquete unidad principal 1 componentes de instalación y conexiones 1 juego 122
- Salidas salidas de altavoz impedancia de altavoz 4 ω 8 ω salida de potencia máxima 55 w 4 a 4 ω 122
- Sección del amplificador de potencia 122
- General 123
- Recepción de radio 123
- Solución de problemas 123
- Mensajes 124
- Reproducción de cd 124
- Reproducción de dispositivo usb 124
- Funcionamiento de rds 125
- Para la utilización del mando a distancia en el volante 125
- Reproducción de cd 125
- Reproducción de dispositivo usb 125
- Operación de actualización del firmware 126
- Ajuste del ángulo de montaje 127
- Conexión instalación 127
- Lista de piezas para la instalación 127
- Precauciones 127
- Conexión 128
- Al conector de alimentación del vehículo 129
- Al conector del altavoz del vehículo 129
- Antes de conectar los altavoces apague la unidad utilice unos altavoces con una impedancia de 4 ω a 8 ω y con una capacidad de administración de la potencia suficiente para evitar daños 129
- Compruebe el conector de alimentación auxiliar de su vehículo y conecte los cables correctamente en función del vehículo 129
- Conexión del altavoz 129
- Conexión del soporte de la memoria 129
- Conexión fácil de subwoofer 129
- Diagrama de conexión de la alimentación 129
- Establecimiento de conexiones 129
- Puede utilizar un subwoofer sin un amplificador de potencia si está conectado a un cable de altavoz trasero 129
- Si el cable de alimentación amarillo está conectado siempre se suministrará alimentación eléctrica al circuito de memoria aunque esté apagado el interruptor de la llave de encendido 129
- Si tiene una antena motorizada sin caja de relés la conexión de esta unidad con el cable de conexión de alimentación suministrado puede dañar la antena 129
- Desmontaje de la abrazadera de protección y el soporte 130
- Instalación 130
- Uso del control remoto con cable 130
- Coloque el soporte dentro del salpicadero y a continuación doble los ganchos hacia fuera para que queden bien ajustados 131
- Montaje de la unidad en el salpicadero 131
- Montaje y desmontaje del panel frontal 131
- Monte la unidad en el soporte y fije la abrazadera de protección 131
- Reinicio de la unidad 131
- Sustitución de fusibles 131
- Fm mw lw cd автомобильное аудио 132
- Информация для покупателей в украине 132
- Предупреждение для случаев когда в замке зажигания нет положения acc 132
- Утилизация использованных элементов питания и отслужившего электрического и электронного оборудования директива применима в странах евросоюза и других странах где действуют системы раздельного сбора отходов 132
- Отказ от ответственности в отношении услуг предоставляемых сторонними поставщиками 133
- Воспроизведение 134
- Дополнительная информация 134
- Начало работы 134
- Параметры 134
- Прослушивание радио 134
- Содержание 134
- Установка подключение 134
- Основное устройство 135
- Справочник по деталям и органам управления 135
- Нажмите и удерживайте кнопки dspl и eq более 2 секунд 137
- Нажмите и удерживайте кнопку off до тех пор пока устройство не отключится нажмите кнопку снятия передней панели а затем потяните панель на себя и снимите ее 137
- Начало работы 137
- Перезагрузка устройства 137
- Поворачивая дисковый регулятор выберите europe или russia а затем нажмите дисковый регулятор 137
- Поворачивая дисковый регулятор выберите yes или no а затем нажмите дисковый регулятор 137
- Предупредительный звуковой сигнал 137
- При отображении set area нажмите кнопку enter 137
- Снятие передней панели 137
- Установка передней панели 137
- Установка страны региона 137
- Подключение устройства usb 138
- Проверка напряжения в аккумуляторе 138
- Установка часов 138
- Автоматическое сохранение btm 139
- Выключите переносное аудиоустройство 139
- Выполните настройку 139
- Выравнивание уровня громкости подключенного устройства с другими источниками 139
- Нажимая кнопку mode измените диапазон fm1 fm2 fm3 или mw lw 139
- Нажимая кнопку src выберите aux 139
- Нажмите кнопку menu поверните дисковый регулятор для выбора general затем нажмите дисковый регулятор 139
- Настройка 139
- Поворачивая дисковый регулятор выберите set btm затем нажмите дисковый регулятор 139
- Подключение другого переносного аудиоустройства 139
- Подключите переносное аудиоустройство ко входному гнезду aux мини стереоразъему на аппарате при помощи соединительного кабеля не входит в комплект поставки 139
- Прослушивание радио 139
- Уменьшите громкость на аппарате 139
- Во время приема радиостанции которую необходимо сохранить нажмите и удерживайте номерную кнопку 1 6 пока не появится индикация mem 140
- Выберите диапазон затем нажмите номерную кнопку 1 6 140
- Для настройки громкости во время приема сообщения о текущей ситуации на дорогах 140
- Для приема экстренных сообщений 140
- Для прослушивания одной региональной программы regional 140
- Для сохранения станций rds с параметрами af и ta 140
- Нажмите кнопку menu поверните дисковый регулятор для выбора general затем нажмите дисковый регулятор 140
- Поворачивая дисковый регулятор выберите set af on set ta on set af ta on или set af ta off затем нажмите дисковый регулятор 140
- Поворачивая дисковый регулятор выберите set af ta затем нажмите дисковый регулятор 140
- Прием радиостанций сохраненных в памяти 140
- Системы радиоданных rds 140
- Сохранение вручную 140
- Установка альтернативных частот af и сообщений о текущей ситуации на дорогах ta 140
- Функция местной привязки только для великобритании 140
- Воспроизведение 141
- Воспроизведение диска 141
- Воспроизведение устройства usb 141
- Вставьте диск этикеткой вверх 141
- Выбор типов программ pty 141
- Нажмите pty во время приема в диапазоне fm 141
- Поворачивайте дисковый регулятор пока не отобразится требуемый тип программы затем нажмите дисковый регулятор 141
- Тип программ 141
- Повторное воспроизведение и воспроизведение в случайной последовательности 142
- Поиск и воспроизведение композиций 142
- Поиск композиции по названию quick browzer 142
- Основные операции настройки параметров 143
- Отмена режима demo 143
- Параметры 143
- Поиск с пропуском элементов режим перехода 143
- Для возврата к предыдущему дисплею 144
- Настройка общих параметров general 144
- Настройка звука sound 145
- Настройка дисплея display 146
- Дополнительная информация 147
- Конденсация влаги 147
- Меры предосторожности 147
- Обновление микропрограммы 147
- Примечания относительно дисков 147
- Порядок воспроизведения аудиофайлов 148
- Примечания относительно дисков cd r cd rw 148
- Уход за устройством 148
- Чистка контактов 148
- Общая информация 149
- Проигрыватель usb 149
- Раздел проигрывателя cd 149
- Технические характеристики 149
- Тюнер 149
- Усилитель мощности 149
- Libflac 150
- Авторские права 150
- Поиск и устранение неисправностей 150
- Общая информация 151
- Прием радиостанций 151
- Воспроизведение дисков cd 152
- Воспроизведение с устройства usb 152
- Воспроизведение дисков cd 153
- Воспроизведение с устройства usb 153
- Сообщения 153
- Примечания по обновлению микропрограммного обеспечения 154
- Примечания по работе пульта дистанционного управления на руле 154
- Функционирование rds 154
- Внимание 155
- Меры предосторожности 155
- Перечень деталей для установки 155
- Регулировка угла установки 155
- Установка подключение 155
- Подключение 156
- Если используется внешняя антенна с электроприводом без релейного блока подсоединение этого устройства с помощью прилагаемого провода питания может привести к повреждению антенны 157
- К разъему громкоговорителя автомобиля 157
- К разъему электропитания автомобиля 157
- Когда к устройству подсоединен желтый провод питания блок памяти будет постоянно получать питание даже при выключенном зажигании 157
- Перед подключением громкоговорителей выключите устройство во избежание повреждений используйте громкоговорители с полным сопротивлением 4 ω 8 ω и соответствующей предельно допустимой мощностью 157
- Подключение громкоговорителей 157
- Подсоединение для поддержки памяти 157
- Простое подключение сабвуфера 157
- Сабвуфер можно использовать без усилителя мощности если подключить его к проводу заднего громкоговорителя 157
- Установка соединений 157
- Если в автомобиле нет положения acc 158
- Если красный и желтый провода переставлены местами 158
- Использование проводного пульта дистанционного управления 158
- Общая схема подключения 158
- После проверки соответствия соединений и проводов импульсного источника электропитания подключите устройство к автомобильному контуру электропитания в случае возникновения каких либо вопросов или проблем связанных с подключением устройства которые не рассматриваются в настоящем руководстве обратитесь за советом к дилеру автомобильной фирмы 158
- Проверьте разъем подключения вспомогательного питания автомобиля и правильно подключите провода в зависимости от типа автомобиля 158
- Схема подключения питания 158
- Чтобы активировать проводной пульт дистанционного управления установите для str control в настройках set steering значение preset стр 14 158
- Отсоединение защитной манжеты и кронштейна 159
- Установка 159
- Установка устройства в приборной панели 159
- Замена предохранителя 160
- Перезагрузка устройства 160
- Снятие и установка передней панели 160
- Deutsch 162
- Eesti keel 162
- English 162
- Français 162
- Hrvatski 162
- Italiano 162
- Magyar 162
- Nederlands 162
- Česky 162
- Ελληνικά 162
- Български 162
- Español 163
- Latviešu 163
- Lietuvių kalba 163
- Polski 163
- Português 163
- Română 163
- Slovensky 163
- Slovenščina 163
- Srpski 163
- Svenska 163
- Türkçe 163
- Македонски 163
- 2018 sony corporation printed in thailand http www sony net 164
- Aplicación para smartphone 164
- App de smartphone 164
- App per smartphone 164
- Http www sony eu mysony 164
- Http www sony eu support 164
- Https sony net sbs 164
- Site d assistance 164
- Sitio web de soporte técnico en línea 164
- Sito di assistenza clienti 164
- Smartphone app 164
- Support site 164
- Support website 164
- Приложение для смартфонов 164
- Сайт для получения поддержки 164
Похожие устройства
- Bosch NatureCool KGV39XK2AR Инструкция по эксплуатации
- Hi HTD015552W Инструкция по эксплуатации
- Ezetil E 40 М 12/230V Gray Инструкция по эксплуатации
- Igloo Collapse&Cool 36 (165156) Инструкция по эксплуатации
- Tefal Air Force Extreme Silence 32V TY8996RO Инструкция по эксплуатации
- Philips FC8780/08 Performer Silent Инструкция по эксплуатации
- Gefest 5100-04 0001 Руководство по эксплуатации
- AEG Вентилятор Инструкция по эксплуатации
- Hotpoint-Ariston 7H PHR 640 ST (OW) Инструкция по эксплуатации
- Samsung NQ50C7535DS/WT Инструкция по эксплуатации
- AOC E2470SWDA Black Инструкция по эксплуатации
- Acer V206HQLAb Black (UM.IV6EE.A02) Инструкция по эксплуатации
- Asus VG249Q Инструкция по эксплуатации
- Samsung S32AM500NI Инструкция по эксплуатации
- Siemens ET 675 MN31D Инструкция по эксплуатации
- Bosch CMG 636BS1 Инструкция по эксплуатации
- Benq BL2711U (9H.LD2LB.QBE) Инструкция по эксплуатации
- A4Tech Fstyler FM10 Black/Blue Инструкция по эксплуатации
- Logitech Keyboard K120 (920-002506) Инструкция по эксплуатации
- Sven Standard 304 USB+HUB Black Руководство по эксплуатации