Daikin D2CND035A4AB [10/12] Error codes

Daikin D2CND028A1AA [10/12] Error codes
7 Error codes
Operation manual
10
D2CND028+035A1/4AA + D2TND028+035A4AA
Wall-mounted condensing boiler
3P469438-5D – 2017.06
# Problem Solution
12-65 Ignition SCOT
actuators fault does
not take place
Perform reset if needed. If problem
repeats, contact your service agent.
12-66 Ion base value
exceeds lower factory
limit
Perform reset. If problem repeats,
contact your service agent.
12-67 Ion base value
exceeds upper
factory limit
Perform reset. If problem repeats,
contact your service agent.
12-68 Ion base value differs
excessively from
previous value
Perform reset if needed. If problem
repeats, contact your service agent.
12-69 Offset adaption at
limit
Boiler continues operation but
contact your service agent.
12-70 Offset adaption not
executable
Boiler continues operation but
contact your service agent.
13-64 Fan speed error Perform reset if needed. If problem
repeats, contact your service agent.
13-65 Fan speed error Perform reset. If problem repeats,
contact your service agent.
16-64 Flue temperature
signalise overheating
Check flue gas discharge path.
Perform reset if needed. If problem
repeats, contact your service agent.
1J-64 High limit thermostat
signalise overheating
Check the valves of the radiators
in the heating circuit.
Check the combi boiler water
pressure. If it is low, fill the heating
circuit with water.
Perform reset. If problem repeats,
contact your service agent.
80-01 Return temperature
sensor fault
Perform reset. If problem repeats,
contact your service agent.
81-01 Flow temperature
sensor fault
Perform reset. If problem repeats,
contact your service agent.
81-65 Domestic hot water
solar temperature
sensor fault
Boiler continues operation but solar
sensor is defective. Contact your
service agent.
8A-46 Freeze protection Unit does not operate if flow
temperature sensor reads value less
than 1°C. Wait until the error code is
removed from the screen.
8H-64 Flow temperature
steep rise
Make sure radiator valves are open
enough to circulate water. Your
boiler will operate again after a while.
If problem repeats, contact your
service agent.
8H-65 Flow-return
temperature
difference too much
Make sure radiator valves are open
enough to circulate water. If problem
repeats, contact your service agent.
E1-64 Flame detection
before burner
operation
Perform reset. If problem repeats,
contact your service agent.
E1-65 Internal SCOT
system error
Perform reset if needed. If problem
repeats, contact your service agent.
E1-66 Calibration conditions
fault
No reset needed. Wait burner to
restart. If problem repeats, contact
your service agent.
E1-67 Missing calibration Perform reset. If problem repeats,
contact your service agent.
E1-68 Ion base value is
outside the factory
limits or saved
incorrectly
Perform reset. If problem repeats,
contact your service agent.
# Problem Solution
E1-69 Parameter CRC error Perform reset. If problem repeats,
contact your service agent.
E1-70 Parameter CRC error Perform reset. If problem repeats,
contact your service agent.
E1-71 EK lockout failure Permanent error. Contact your
service agent.
E1-72 SCOT flame amplifier Perform reset if needed. If problem
repeats, contact your service agent.
E1-73 Internal PCB error Perform reset if needed. If problem
repeats, contact your service agent.
H9-01 Outside sensor fault Boiler continues operation but
outside sensor is defective. Contact
your service agent.
HC-01 Domestic hot water
temperature sensor
fault
Boiler continues operation but you
must contact your service agent.
HJ-08 High system pressure Discharge water down to 0.8bar.
(You can bleed the radiators.)
HJ-09 Low system pressure Increase the system pressure to
0.8bar
HJ-10 Water pressure
sensor fault
Contact your service agent.
J6-01 Flow temperature
sensor overheating
(Can be a blocking
error or a lockout
error)
Check the valves of the radiators
in the heating circuit.
Check the combi boiler water
pressure. If it is low, fill the heating
circuit with water.
Perform reset if needed. If problem
repeats, contact your service
agent.
J6-20 Return temperature
sensor overheating
(Can be a blocking
error or a lockout
error)
Perform reset if needed. If problem
repeats, contact your service agent.
J6-21 Return temperature is
higher than flow
temperature
No reset needed, burner operates
itself after a small amount of time. If
problem repeats, contact your
service agent.
JJ-64 Flue temperature
sensor fault
Perform reset. If problem repeats,
contact your service agent.
U2-01 Supply voltage is
below low limit
Contact your service agent.
U2-01 Supply voltage is
above high limit
Your boiler will continue operation
but you must contact your service
agent.
U4-65 Opentherm room
thermostat
connection is
defective
Your boiler will continue operation
but Opentherm room thermostat is
out of operation. Contact your
service agent.
U4-66 CAN-bus timeout If problem repeats, contact your
service agent.
U4-67 Remote reset
supervision
Switch off - switch on power mains. If
problem repeats, contact your
service agent.
UA-64 Blocking during BCC
update process
Contact your service agent.
UA-65 PCB requires a BCC
update
Contact your service agent.
UA-66 BCC-ID of internal
EEPROM is
inconsistent
Contact your service agent.
UA-67 BCC is missing Contact your service agent.

Содержание

Скачать