Candy CBTD 7A1TE-S [20/124] Le linge

Candy CBTD 7A1TE-S [20/124] Le linge
20
Ne séchez pas des vêtements non
lavés dans le sèche-linge.
ATTENTION NE chez PAS les
tissus qui ont été traités avec des
liquides de nettoyage à sec.
ATTENTION Quand elles sont
c h a u ffées, l e s mousses
alvéolaires peuvent dans certains
cas brûler par combustion
spontanée Les articles en mousse
caoutchouc (mousse de latex), les
bonnets de douche, le textile
imperméable, les articles
caoutchoutés et les vêtements ou
coussins rembourrés de mousse
c
aoutchouc NE DOIVENT PAS
être séchés dans le sèche-linge.
Reportez-vous toujours aux
étiquettes dentretien du linge pour
rifier le mode de séchage
recommandé.
Les vêtements doivent être
essorés en machine ou à la main
avant d’être placés dans le che-
linge. Les vêtements qui
dégoulinent NE DOIVENT PAS
être mis dans le sèche-linge.
Enlevez les briquets et les
allumettes des poches et veillez à
ne JAMAIS utiliser des liquides
inflamma
bles à proximité de la
machine.
Les rideaux en fibres de verre ne
doivent JAMAIS être placés dans
cette machine. La contamination
dautres vêtements par les fibres
de verre peut entraîner des
irritations de la peau.
Les articles qui ont été souillés par
des substances telles que huile de
cuisson, acétone, alcool, pétrole,
kérosène, produit anti-taches,
térébenthine, cire et décapant pour
Le Linge
cire doivent être lavés à l'eau
chaude avec une quantité
supplémentaire de détergent
av
ant d'être séchés dans le
sèche-linge.
Les agents adoucissants, et
autres produits similaires,
d o i v e n t ê t r e u t i l i s é s
conformément aux instructions
fournies par le fabricant du
produit.
Ventilation
La pièce se trouve le sèche-
linge doit avoir une ventilation
adéquate de manière à ce que
les gaz des appareils qui
brûlent d’autres combustibles,
y compris les cheminées, ne
soient pas attirés dans la pièce
pendant que le sèche-linge est
en marche
Installez l'arrière de l'appareil
près d'un mur ou d'une surface
verticale.
Il doit y avoir un espace
minimum de 12 mm entre la
machine et quelconque
obstacle. L'entrée et la sortie
d'air doivent être dégagées.
Pour as
surer une ventilation
adéquate, l'espace entre le
bas de la machine et le sol ne
doit pas être obstrué.
Lair d’ échappement ne doit
pas être évacué par un conduit
qui est également utilisé pour
é v a c u e r l e s f u m é e s
déchappement dappareils
qui brûlent du gaz ou d’autres
combustibles.
15
NEXT TIME Regular usage
Every time you want to manage the
machine through the App, first you have to
enable the Smart Touch mode by turning
the knob to the Smart Touch indicator.
Make sure you have unlocked your phone
(from stand-by mode) and you have
activated the NFC function; then, follow the
steps mentioned earlier.
If you want to start a dry cycle, load
the laundry and close the door.
Select the desired function in the App (e.g.:
starting a programme, the Smart Check-
up cycle, update statistics, etc…).
Follow the instructions on the phone
display, KEEPING IT ON the Smart Touch
logo on the machine dashboard, when
requested to do so by the App.
NOTES:
Place your smartphone so that the NFC
antenna on its back matches the position
of the Smart Touch logo on the appliance
(as illustrate below).
If you do not know the position of your NFC
antenna, slightly move the smartphone in a
circular motion over the Smart Touch logo
until the App confirms the connection. In
order for the data transfer to be successful,
it is essential TO KEEP THE SMARTPHONE
ON THE DASHBOARD DURING THESE THE
FEW SECONDS OF THE PROCEDURE; a
message on the device will inform about the
correct outcome of the operation and
advise you when it is possible to move the
smartphone away.
Thick cases or metallic stickers on your
smartphone could affect or prevent the
transmission of data between machine
and telephone. If necessary, remove them.
The replacement of some components of
the smartphone (e.g. back cover, battery,
etc...) with non-original ones, could result
in the NFC antenna removal, preventing
the full use of the App.
The management and the control of the
machine via App is only possible "by
proximity": it is therefore not possible to
perform remote operations (e.g.: from
another room; outside of the house).
WIRELESS PARAMETERS
With this the Candy Hoover Group Srl,
declares that this appliance marked with
complies with the essential
requirements of the Directive 2014/53/EU.
To receive a copy of the declaration of
c o n f o r m i t y, p l e a s e c o n t a c t t h e
manufacturer at:
www.candy-group.com
Wireless Standard
ISO/IEC 14443 Type A and NFC Forum Type 4
Frequency band
Magnetic field limit
13,553-13,567 MHz (centre frequency 13,560 MHz)
< 42dBμA/m (at 10 meters)
Parameter
Specifications
EN
15
NEXT TIME Regular usage
Every time you want to manage the
machine through the App, first you have to
enable the Smart Touch mode by turning
the knob to the Smart Touch indicator.
Make sure you have unlocked your phone
(from stand-by mode) and you have
activated the NFC function; then, follow the
steps mentioned earlier.
If you want to start a dry cycle, load
the laundry and close the door.
Select the desired function in the App (e.g.:
starting a programme, the Smart Check-
up cycle, update statistics, etc…).
Follow the instructions on the phone
display, KEEPING IT ON the Smart Touch
logo on the machine dashboard, when
requested to do so by the App.
NOTES:
Place your smartphone so that the NFC
antenna on its back matches the position
of the Smart Touch logo on the appliance
(as illustrate below).
If you do not know the position of your NFC
antenna, slightly move the smartphone in a
circular motion over the Smart Touch logo
until the App confirms the connection. In
order for the data transfer to be successful,
it is essential TO KEEP THE SMARTPHONE
ON THE DASHBOARD DURING THESE THE
FEW SECONDS OF THE PROCEDURE; a
message on the device will inform about the
correct outcome of the operation and
advise you when it is possible to move the
smartphone away.
Thick cases or metallic stickers on your
smartphone could affect or prevent the
transmission of data between machine
and telephone. If necessary, remove them.
The replacement of some components of
the smartphone (e.g. back cover, battery,
etc...) with non-original ones, could result
in the NFC antenna removal, preventing
the full use of the App.
The management and the control of the
machine via App is only possible "by
proximity": it is therefore not possible to
perform remote operations (e.g.: from
another room; outside of the house).
WIRELESS PARAMETERS
With this the Candy Hoover Group Srl,
declares that this appliance marked with
complies with the essential
requirements of the Directive 2014/53/EU.
To receive a copy of the declaration of
c o n f o r m i t y, p l e a s e c o n t a c t t h e
manufacturer at:
www.candy-group.com
Wireless Standard
ISO/IEC 14443 Type A and NFC Forum Type 4
Frequency band
Magnetic field limit
13,553-13,567 MHz (centre frequency 13,560 MHz)
< 42dBμA/m (at 10 meters)
Parameter
Specifications
EN
15
NEXT TIME Regular usage
Every time you want to manage the
machine through the App, first you have to
enable the Smart Touch mode by turning
the knob to the Smart Touch indicator.
Make sure you have unlocked your phone
(from stand-by mode) and you have
activated the NFC function; then, follow the
steps mentioned earlier.
If you want to start a dry cycle, load
the laundry and close the door.
Select the desired function in the App (e.g.:
starting a programme, the Smart Check-
up cycle, update statistics, etc…).
Follow the instructions on the phone
display, KEEPING IT ON the Smart Touch
logo on the machine dashboard, when
requested to do so by the App.
NOTES:
Place your smartphone so that the NFC
antenna on its back matches the position
of the Smart Touch logo on the appliance
(as illustrate below).
If you do not know the position of your NFC
antenna, slightly move the smartphone in a
circular motion over the Smart Touch logo
until the App confirms the connection. In
order for the data transfer to be successful,
it is essential TO KEEP THE SMARTPHONE
ON THE DASHBOARD DURING THESE THE
FEW SECONDS OF THE PROCEDURE; a
message on the device will inform about the
correct outcome of the operation and
advise you when it is possible to move the
smartphone away.
Thick cases or metallic stickers on your
smartphone could affect or prevent the
transmission of data between machine
and telephone. If necessary, remove them.
The replacement of some components of
the smartphone (e.g. back cover, battery,
etc...) with non-original ones, could result
in the NFC antenna removal, preventing
the full use of the App.
The management and the control of the
machine via App is only possible "by
proximity": it is therefore not possible to
perform remote operations (e.g.: from
another room; outside of the house).
WIRELESS PARAMETERS
With this the Candy Hoover Group Srl,
declares that this appliance marked with
complies with the essential
requirements of the Directive 2014/53/EU.
To receive a copy of the declaration of
c o n f o r m i t y, p l e a s e c o n t a c t t h e
manufacturer at:
www.candy-group.com
Wireless Standard
ISO/IEC 14443 Type A and NFC Forum Type 4
Frequency band
Magnetic field limit
13,553-13,567 MHz (centre frequency 13,560 MHz)
< 42dBμA/m (at 10 meters)
Parameter
Specifications
EN
15
NEXT TIME Regular usage
Every time you want to manage the
machine through the App, first you have to
enable the Smart Touch mode by turning
the knob to the Smart Touch indicator.
Make sure you have unlocked your phone
(from stand-by mode) and you have
activated the NFC function; then, follow the
steps mentioned earlier.
If you want to start a dry cycle, load
the laundry and close the door.
Select the desired function in the App (e.g.:
starting a programme, the Smart Check-
up cycle, update statistics, etc…).
Follow the instructions on the phone
display, KEEPING IT ON the Smart Touch
logo on the machine dashboard, when
requested to do so by the App.
NOTES:
Place your smartphone so that the NFC
antenna on its back matches the position
of the Smart Touch logo on the appliance
(as illustrate below).
If you do not know the position of your NFC
antenna, slightly move the smartphone in a
circular motion over the Smart Touch logo
until the App confirms the connection. In
order for the data transfer to be successful,
it is essential TO KEEP THE SMARTPHONE
ON THE DASHBOARD DURING THESE THE
FEW SECONDS OF THE PROCEDURE; a
message on the device will inform about the
correct outcome of the operation and
advise you when it is possible to move the
smartphone away.
Thick cases or metallic stickers on your
smartphone could affect or prevent the
transmission of data between machine
and telephone. If necessary, remove them.
The replacement of some components of
the smartphone (e.g. back cover, battery,
etc...) with non-original ones, could result
in the NFC antenna removal, preventing
the full use of the App.
The management and the control of the
machine via App is only possible "by
proximity": it is therefore not possible to
perform remote operations (e.g.: from
another room; outside of the house).
WIRELESS PARAMETERS
With this the Candy Hoover Group Srl,
declares that this appliance marked with
complies with the essential
requirements of the Directive 2014/53/EU.
To receive a copy of the declaration of
c o n f o r m i t y, p l e a s e c o n t a c t t h e
manufacturer at:
www.candy-group.com
Wireless Standard
ISO/IEC 14443 Type A and NFC Forum Type 4
Frequency band
Magnetic field limit
13,553-13,567 MHz (centre frequency 13,560 MHz)
< 42dBμA/m (at 10 meters)
Parameter
Specifications
EN
15
NEXT TIME Regular usage
Every time you want to manage the
machine through the App, first you have to
enable the Smart Touch mode by turning
the knob to the Smart Touch indicator.
Make sure you have unlocked your phone
(from stand-by mode) and you have
activated the NFC function; then, follow the
steps mentioned earlier.
If you want to start a dry cycle, load
the laundry and close the door.
Select the desired function in the App (e.g.:
starting a programme, the Smart Check-
up cycle, update statistics, etc…).
Follow the instructions on the phone
display, KEEPING IT ON the Smart Touch
logo on the machine dashboard, when
requested to do so by the App.
NOTES:
Place your smartphone so that the NFC
antenna on its back matches the position
of the Smart Touch logo on the appliance
(as illustrate below).
If you do not know the position of your NFC
antenna, slightly move the smartphone in a
circular motion over the Smart Touch logo
until the App confirms the connection. In
order for the data transfer to be successful,
it is essential TO KEEP THE SMARTPHONE
ON THE DASHBOARD DURING THESE THE
FEW SECONDS OF THE PROCEDURE; a
message on the device will inform about the
correct outcome of the operation and
advise you when it is possible to move the
smartphone away.
Thick cases or metallic stickers on your
smartphone could affect or prevent the
transmission of data between machine
and telephone. If necessary, remove them.
The replacement of some components of
the smartphone (e.g. back cover, battery,
etc...) with non-original ones, could result
in the NFC antenna removal, preventing
the full use of the App.
The management and the control of the
machine via App is only possible "by
proximity": it is therefore not possible to
perform remote operations (e.g.: from
another room; outside of the house).
WIRELESS PARAMETERS
With this the Candy Hoover Group Srl,
declares that this appliance marked with
complies with the essential
requirements of the Directive 2014/53/EU.
To receive a copy of the declaration of
c o n f o r m i t y, p l e a s e c o n t a c t t h e
manufacturer at:
www.candy-group.com
Wireless Standard
ISO/IEC 14443 Type A and NFC Forum Type 4
Frequency band
Magnetic field limit
13,553-13,567 MHz (centre frequency 13,560 MHz)
< 42dBμA/m (at 10 meters)
Parameter
Specifications
EN
15
NEXT TIME Regular usage
Every time you want to manage the
machine through the App, first you have to
enable the Smart Touch mode by turning
the knob to the Smart Touch indicator.
Make sure you have unlocked your phone
(from stand-by mode) and you have
activated the NFC function; then, follow the
steps mentioned earlier.
If you want to start a dry cycle, load
the laundry and close the door.
Select the desired function in the App (e.g.:
starting a programme, the Smart Check-
up cycle, update statistics, etc…).
Follow the instructions on the phone
display, KEEPING IT ON the Smart Touch
logo on the machine dashboard, when
requested to do so by the App.
NOTES:
Place your smartphone so that the NFC
antenna on its back matches the position
of the Smart Touch logo on the appliance
(as illustrate below).
If you do not know the position of your NFC
antenna, slightly move the smartphone in a
circular motion over the Smart Touch logo
until the App confirms the connection. In
order for the data transfer to be successful,
it is essential TO KEEP THE SMARTPHONE
ON THE DASHBOARD DURING THESE THE
FEW SECONDS OF THE PROCEDURE; a
message on the device will inform about the
correct outcome of the operation and
advise you when it is possible to move the
smartphone away.
Thick cases or metallic stickers on your
smartphone could affect or prevent the
transmission of data between machine
and telephone. If necessary, remove them.
The replacement of some components of
the smartphone (e.g. back cover, battery,
etc...) with non-original ones, could result
in the NFC antenna removal, preventing
the full use of the App.
The management and the control of the
machine via App is only possible "by
proximity": it is therefore not possible to
perform remote operations (e.g.: from
another room; outside of the house).
WIRELESS PARAMETERS
With this the Candy Hoover Group Srl,
declares that this appliance marked with
complies with the essential
requirements of the Directive 2014/53/EU.
To receive a copy of the declaration of
c o n f o r m i t y, p l e a s e c o n t a c t t h e
manufacturer at:
www.candy-group.com
Wireless Standard
ISO/IEC 14443 Type A and NFC Forum Type 4
Frequency band
Magnetic field limit
13,553-13,567 MHz (centre frequency 13,560 MHz)
< 42dBμA/m (at 10 meters)
Parameter
Specifications
EN
15
NEXT TIME Regular usage
Every time you want to manage the
machine through the App, first you have to
enable the Smart Touch mode by turning
the knob to the Smart Touch indicator.
Make sure you have unlocked your phone
(from stand-by mode) and you have
activated the NFC function; then, follow the
steps mentioned earlier.
If you want to start a dry cycle, load
the laundry and close the door.
Select the desired function in the App (e.g.:
starting a programme, the Smart Check-
up cycle, update statistics, etc…).
Follow the instructions on the phone
display, KEEPING IT ON the Smart Touch
logo on the machine dashboard, when
requested to do so by the App.
NOTES:
Place your smartphone so that the NFC
antenna on its back matches the position
of the Smart Touch logo on the appliance
(as illustrate below).
If you do not know the position of your NFC
antenna, slightly move the smartphone in a
circular motion over the Smart Touch logo
until the App confirms the connection. In
order for the data transfer to be successful,
it is essential TO KEEP THE SMARTPHONE
ON THE DASHBOARD DURING THESE THE
FEW SECONDS OF THE PROCEDURE; a
message on the device will inform about the
correct outcome of the operation and
advise you when it is possible to move the
smartphone away.
Thick cases or metallic stickers on your
smartphone could affect or prevent the
transmission of data between machine
and telephone. If necessary, remove them.
The replacement of some components of
the smartphone (e.g. back cover, battery,
etc...) with non-original ones, could result
in the NFC antenna removal, preventing
the full use of the App.
The management and the control of the
machine via App is only possible "by
proximity": it is therefore not possible to
perform remote operations (e.g.: from
another room; outside of the house).
WIRELESS PARAMETERS
With this the Candy Hoover Group Srl,
declares that this appliance marked with
complies with the essential
requirements of the Directive 2014/53/EU.
To receive a copy of the declaration of
c o n f o r m i t y, p l e a s e c o n t a c t t h e
manufacturer at:
www.candy-group.com
Wireless Standard
ISO/IEC 14443 Type A and NFC Forum Type 4
Frequency band
Magnetic field limit
13,553-13,567 MHz (centre frequency 13,560 MHz)
< 42dBμA/m (at 10 meters)
Parameter
Specifications
EN

Содержание

Скачать