![Daikin RXYQ30PYNKE [6/24] Introduction](/img/pdf.png)
Daikin RXYQ30PYNKE [6/24] Introduction
![Daikin RXYQ36PYNK [6/24] Introduction](/views2/1790733/page6/bg6.png)
2 English
• Install the indoor and outdoor units, power cord and connecting
wires at least 1 meter away from televisions or radios to prevent
picture interference and noise.
(Depending on the incoming signal strength, a distance of 1 meter
may not be sufficient to eliminate noise.)
• Remote controller (wireless kit) transmitting distance can be
shorter than expected in rooms with electronic fluorescent lamps
(inverter or rapid start types).
Install the indoor unit as far away from fluorescent lamps as pos-
sible.
• Make sure to provide for adequate measures in order to prevent
that the outdoor unit be used as a shelter by small animals.
Small animals making contact with electrical parts can cause mal-
functions, smoke or fire. Please instruct the customer to keep the
area around the unit clean.
• Do not install the air conditioner in the following locations:
1. Where there is a high concentration of mineral oil spray or
vapour (e.g. a kitchen).
Plastic parts will deteriorate, parts may fall off and water leak-
age could result.
2. Where corrosive gas, such as sulphurous acid gas, is pro-
duced.
Corroding of copper pipes or soldered parts may result in
refrigerant leakage.
3. Near machinery emitting electromagnetic radiation.
Electromagnetic radiation may disturb the operation of the
control system and result in a malfunction of the unit.
4. Where flammable gas may leak, where there is carbon fibre or
ignitable dust suspensions in the air, or where volatile flamma-
bles such as paint thinner or gasoline are handled.
Operating the unit in such conditions may result in fire.
1-2 Special notice of product
[CLASSIFICATION]
This air conditioner comes under the term “appliances not accessible
to the general public”.
[REFRIGERANT]
VRVIII System use R410A refrigerant.
• The refrigerant R410A requires that strict precautions be
observed for keeping the system clean, dry and tightly sealed.
Read the chapter “REFRIGERANT PIPING” carefully and follow
these procedures correctly.
A.Clean and dry
Strict measures must be taken to keep impurities (including
SUNISO oil and other mineral oils as well as moisture) out of
the system.
B.Tight sealed
Take care to keep the system tight when installing.
R410A contains no chlorine, does not destroy the ozone layer
and so does not reduce the earth’s protection against harmful
ultraviolet radiation.
R410A will contribute only slightly to the greenhouse effect if
released into the atmosphere.
• Since R410A is a mixed refrigerant, the required additional refrig-
erant must be charged in its liquid state. (If the system is charged
with refrigerant in its gaseous state, due to composition change,
the system will not function normally.)
[DESIGN PRESSURE]
Since design pressure is 4.0MPa or 40bar (for R407C units: 3.3MPa
or 33bar),the wall thickness of pipes should be more carefully
selected in accordance with the relevant local and national regula-
tions.
1-3 Disposal requirements
Dismantling of the unit, treatment of the refrigerant, of oil and of other
parts must be done in accordance with relevant local and national
legislation.
2. INTRODUCTION
• RXYQ-P series are designed for outdoor installation and used for
cooling and heatpump applications. Outdoor units come in three
standard sizes, and with a single system through a multi system
combining up to three outdoor units, rated cooling capacity from
17.7 kW to 81.6 kW and rated heating capacity from 25.0 kW to
112.5 kW can be achieved.
• The RXYQ-P units can be combined with Daikin VRV series
indoor units for air conditioning purposes. Always use appropriate
indoor units compatible with R410A. To lean which models of
indoor units are compatible with R410A, refer to the product cat-
alogs.
To combine with other refrigerant indoor unit will cause malfunc-
tion.
2-1 Combination
The indoor units can be installed in the following range.
〈
Outdoor unit
〉
〈
Total capacity of indoor units
〉〈
Total quantity of indoor units
〉
RXYQ8PTLK(E) · PYNK(E)
...........100 ~260 13 units
RXYQ10PTLK(E) · PYNK(E)
..........125 ~325 16 units
RXYQ12PTLK(E) · PYNK(E)
..........150 ~390 19 units
RXYQ16PTLK(E) · PYNK(E)
..........200 ~520 26 units
RXYQ18PTLK(E) · PYNK(E)
..........225 ~585 29 units
RXYQ20PTLK(E) · PYNK(E)
..........250 ~650 32 units
RXYQ22PTLK(E) · PYNK(E)
..........275 ~715 35 units
RXYQ24PTLK(E) · PYNK(E)
..........300 ~780 39 units
RXYQ26PTLK(E) · PYNK(E)
..........325 ~845 42 units
RXYQ28PTLK(E) · PYNK(E)
..........350 ~910 45 units
RXYQ30PTLK(E) · PYNK(E)
..........375 ~975 48 units
RXYQ32PTLK(E) · PYNK(E)
..........400 ~1040 52 units
RXYQ34PTLK(E) · PYNK(E)
..........425 ~1105 55 units
RXYQ36PTLK(E) · PYNK(E)
..........450 ~1170 58 units
Note
• Be sure to connect an R410A indoor unit.
See the catalog for indoor unit models which can be connected.
• At above is the total capacity and total number of units of the
indoor units when configured in a standard combination. See the
technical reference for details on total capacity and total number
of indoor units when using a configuration other than the standard
combination. The standard combination are as follows.
<Combination unit>
<Independent unit>
RXYQ8PTLK(E) · PYNK(E) RXYQ8PTLK(E) · PYNK(E)
RXYQ10PTLK(E) · PYNK(E) RXYQ10PTLK(E) · PYNK(E)
RXYQ12PTLK(E) · PYNK(E) RXYQ12PTLK(E) · PYNK(E)
RXYQ16PTLK(E) · PYNK(E) RXYQ8PTLK(E) · PYNK(E)+ RXYQ8PTLK(E) · PYNK(E)
RXYQ18PTLK(E) · PYNK(E) RXYQ8PTLK(E) · PYNK(E)+ RXYQ10PTLK(E) · PYNK(E)
RXYQ20PTLK(E) · PYNK(E) RXYQ8PTLK(E) · PYNK(E)+ RXYQ12PTLK(E) · PYNK(E)
RXYQ22PTLK(E) · PYNK(E) RXYQ10PTLK(E) · PYNK(E)+ RXYQ12PTLK(E) · PYNK(E)
RXYQ24PTLK(E) · PYNK(E) RXYQ12PTLK(E) · PYNK(E)+ RXYQ12PTLK(E) · PYNK(E)
RXYQ26PTLK(E) · PYNK(E) RXYQ8PTLK(E) · PYNK(E)+ RXYQ8PTLK(E) · PYNK(E)+ RXYQ10PTLK(E) · PYNK(E)
RXYQ28PTLK(E) · PYNK(E) RXYQ8PTLK(E) · PYNK(E)+ RXYQ10PTLK(E) · PYNK(E)+ RXYQ10PTLK(E) · PYNK(E)
RXYQ30PTLK(E) · PYNK(E) RXYQ8PTLK(E) · PYNK(E)+ RXYQ10PTLK(E) · PYNK(E)+ RXYQ12PTLK(E) · PYNK(E)
RXYQ32PTLK(E) · PYNK(E) RXYQ10PTLK(E) · PYNK(E)+ RXYQ10PTLK(E) · PYNK(E)+ RXYQ12PTLK(E) · PYNK(E)
RXYQ34PTLK(E) · PYNK(E) RXYQ10PTLK(E) · PYNK(E)+ RXYQ12PTLK(E) · PYNK(E)+ RXYQ12PTLK(E) · PYNK(E)
RXYQ36PTLK(E) · PYNK(E) RXYQ12PTLK(E) · PYNK(E)+ RXYQ12PTLK(E) · PYNK(E)+ RXYQ12PTLK(E) · PYNK(E)
• If the total capacity of the connected indoor units exceeds the
capacity of the outdoor unit, cooling and heating performance
may drop when running the indoor units. See the capacity table in
the Engineering Data Book for details.
• There are restrictions on the refrigerant pipe connecting order
between outdoor unit in the case of the multi system.
Install so that the following restrictions are satisfied.
<Restrictions>
The capacities of outdoor units A, B and C must fulfill the following
conditions.
A ≥ B ≥ C
to indoor unit
Outdoor
unit A
Outdoor
unit B
Outdoor
unit C
Outdoor unit
multi connection
piping kit
(first branch)
Outdoor unit multi
connection piping kit
(second branch)
01_EN_3P226891-7A.fm Page 2 Tuesday, June 3, 2008 2:35 PM
Содержание
- Installation manual 1
- System air conditioner 1
- Figure 1 2
- Figure 10 figure 11 figure 12 figure 13 2
- Figure 14 2
- Figure 15 2
- Figure 2 2
- Figure 3 2
- Figure 4 2
- Figure 5 2
- Figure 6 2
- Figure 7 2
- Figure 8 2
- Figure 9 2
- Figure 16 3
- Figure 17 3
- Figure 18 3
- Figure 19 figure 20 3
- Figure 21 3
- Figure 22 3
- Figure 23 3
- Figure 24 3
- Figure 25 3
- Figure 26 3
- Figure 27 4
- Figure 28 4
- Figure 29 figure 30 4
- Figure 31 figure 32 4
- Figure 33 4
- Figure 34 4
- Figure 35 4
- 1 safety precautions 5
- Contents 5
- English 1 5
- First of all 5
- Installation manual 5
- 1 combination 6
- 2 special notice of product 6
- 3 disposal requirements 6
- English 6
- Introduction 6
- 2 standard supplied accessories 7
- 3 option accessory 7
- 4 technical and electrical specifications 7
- 5 main components 7
- 6 installation process 7
- English 3 7
- Selection of location 7
- 1 selection of piping material and refrigerant branching kit 8
- English 8
- Inspecting and handling the unit 8
- Placing the unit 8
- Refrigerant piping 8
- 2 protection against contamination when installing pipes 9
- 3 pipe connection 9
- 4 connecting the refrigerant piping 9
- A b 25 9
- Cutting location 9
- English 5 9
- Gas side accessory pipe 2 9
- Gas side piping field supply 9
- Change as shown in the figure below rising height 200 mm or more 10
- Change to pattern 1 or pattern 2 10
- English 10
- Front connections 10
- If 2 m or more 10
- If less than 2m 10
- Less than 2m 10
- M or more 10
- Oil remains in the stopping outdoor unit 10
- Outdoor unit gas pipe 10
- Pattern 1 10
- Pattern 2 10
- Prohibited pattern 10
- To indoor unit 10
- Unit a 10
- Unit b 10
- English 7 11
- 5 example of connection 12
- English 12
- Example of connection 12
- Example refrigerant branch using refnet header 12
- Example refrigerant branch using refnet joint 12
- Pipe size selection 12
- Refrigerant branch kit selection 12
- _en_3p226891 7a fm page 8 tuesday june 3 2008 2 35 pm 12
- Diameter of above case 13
- English 9 13
- How to calculate the additional refrigerant to be charged 13
- Note 1 13
- Note 2 13
- Note 3 13
- 1 power circuit safety device and cable requirements 14
- 2 wiring connection example for whole system 14
- A power circuit see the following table must be provided for con nection of the unit this circuit must be protected with the required safety devices i e a main switch a slow blow fuse on each phase and an earth leakage circuit breaker when using residual current operated circuit breakers be sure to use a high speed type 1 second or less 200ma rated residual operating current use copper conductors only use insulated wire for the power cord select the power supply cable type and size in accordance with relevant local and national regulations 14
- All field wiring and components must be installed by a licensed electrician and must comply with relevant local and national reg ulations be sure to use a dedicated power circuit never use a power sup ply shared by another appliance 14
- Caution 14
- English 14
- Ex combining the rxyq30ptlk e using rxyq8ptlk e rxyq10ptlk e and rxyq12ptlk e 14
- Field wiring 14
- Minimum circuit amp of rxyq10ptlk e in table above 41 a minimum circuit amp of rxyq12ptlk e in table above 41 a accordingly the minimum circuit amp of the rxyq30ptlk e 32 41 41 115 a multiplying the result above by 1 115 1 127 a so the recommended fuse capacity would be 130 a 14
- Note electrical wiring must be done in accordance with the wiring dia grams and the description herein do not operate until refrigerant piping work is completed if operated before complete the piping work the compressor may be broken down never remove thermistor sensor or etc when connecting power wiring and transmission wiring if operated with thermistor sensor or etc removed the compres sor may be broken down this product have reversed phase protection detector that only works when the power is turned on if there exists black out or the power goes on and off which the product is operating attach a reversed phase protection circuit locally running the product in reversed phase may break the compressor and other parts attach the power wire securely introducing power with a missing n phase or with a mistaken n phase will break the unit never connect the power supply in reversed phase the unit can not operate normally in reversed phase if you connect in reversed phase replace two of the 14
- Note make sure the weak electric wiring i e for the remote control ler between units etc and the power wiring do not pass near each other keeping them at least 50 mm apart proximity may cause electrical interference malfunctions and breakage be sure to connect the power wiring to the power wiring termi nal block and secure it as described in 7 5 power wiring connection procedure 14
- Note the above table indicates power specifications for standard combi nations see 2 introduction if using anything other than the above combinations in a multi sys tem calculate using the following procedure minimum circuit amp value add the minimum circuit amp values for each independent unit 14
- Only proceed with wiring work after blocking off all power always ground wires in accordance with relevant local and national regulations this machine includes an inverter device connect earth and leave charge to eliminate the impact on other devices by reducing noise generated from the inverter device and to prevent leaked current from being charged in the outer hull of the product do not connect the ground wire to gas pipes sewage pipes light ning rods or telephone ground wires gas pipes can explode or catch fire if there is a gas leak sewage pipes no grounding effect is possible if hard plastic pip ing is used telephone ground wires and lightning rods dangerous when struck by lightning due to abnormal rise in electrical potential in the grounding be sure to install an earth leakage circuit breaker this unit uses an inverter so install the earth leakage circuit breaker that be capable of handling high harmonics in order to prevent malfunctioning of the earth leakage circuit breaker i 14
- Refer to figure 19 1 power supply 2 main switch 3 earth leakage circuit breaker 4 fuse 5 outdoor unit 6 cool heat selector 7 remote controller 8 indoor unit 14
- Specifications for local wiring are in compliance with iec60245 use wire type h05vv when protected pipes are used use wire type h07rn f when protected pipes are not used 14
- 3 leading wire procedure 15
- 4 transmission wiring connection procedure 15
- 5 power wiring connection procedure 15
- English 11 15
- 1 preparations 16
- 6 procedure for wiring inside units 16
- Air tight test and vacuum dry ing 16
- Air tight test and vacuum drying 16
- Crimp style terminal 16
- Cup washer 16
- Cut out section 16
- English 16
- Power wire crimp style terminal 16
- Resin hook 16
- Terminal block crip style terminal wire narrow wire thick 16
- 1 before working 17
- 2 air tight test and vacuum drying method 17
- Additional refrigerant charge and check operation 17
- Checking of device and instal lation conditions 17
- Checking of device and installation conditions 17
- English 13 17
- Pipe insulation 17
- English 18
- H h i h h h h 18
- J h h h h h h 18
- J h h h i h i 18
- J h h i h h h 18
- J h j h j j h 18
- 2 procedure of adding refrigerant charging and check operation 19
- Cooling mode 19
- English 15 19
- Heating mode 19
- Outdoor temp 0 c db 43 c db indoor temp 10 c db 32 c db less than above range 19
- English 20
- H h i h h h h 20
- H j h h h 20
- I i i i i i i 20
- I j j i i i i 20
- J j h h i h i 20
- J j j h i h i 20
- English 17 21
- J h h h h h h h h 21
- J h h h h h h h j 21
- J h h i h h h h h 21
- J h h i h h h h i 21
- 1 before test run 22
- 1 onsite settings with the power off 22
- 2 onsite settings with the power on 22
- 2 test run 22
- 3 checks after test run 22
- Caution for refrigerant leaks 22
- English 22
- Onsite settings 22
- Test run 22
- English 19 23
Похожие устройства
- Daikin RXYQ32PTLK Инструкция по эксплуатации
- Daikin RXYQ32PTLK Инструкция по монтажу
- Daikin RXYQ32PTLKE Инструкция по эксплуатации
- Daikin RXYQ32PTLKE Инструкция по монтажу
- Daikin RXYQ32PYNK Инструкция по эксплуатации
- Daikin RXYQ32PYNK Инструкция по монтажу
- Daikin RXYQ32PYNKE Инструкция по эксплуатации
- Daikin RXYQ32PYNKE Инструкция по монтажу
- Daikin RXYQ34PTLK Инструкция по эксплуатации
- Daikin RXYQ34PTLK Инструкция по монтажу
- Daikin RXYQ34PTLKE Инструкция по эксплуатации
- Daikin RXYQ34PTLKE Инструкция по монтажу
- Daikin RXYQ34PYNK Инструкция по монтажу
- Daikin RXYQ34PYNK Инструкция по эксплуатации
- Daikin RXYQ34PYNKE Инструкция по эксплуатации
- Daikin RXYQ34PYNKE Инструкция по монтажу
- Daikin RXYQ36PTLK Инструкция по эксплуатации
- Daikin RXYQ36PTLK Инструкция по монтажу
- Daikin RXYQ36PTLKE Инструкция по эксплуатации
- Daikin RXYQ36PTLKE Инструкция по монтажу