![Daikin EKRTCTRL1 [15/24] Air temperature probe assembly](/img/pdf.png)
Daikin EKRTCTRL1 [15/24] Air temperature probe assembly
![Daikin EKRTCTRL1 [15/24] Air temperature probe assembly](/views2/1795132/page15/bgf.png)
15
S
I
U
B
C
D
A
A
INN-FR-B20
H4
COMM
Y2Y1
H2
DISPLAY INN-DU4
H2
NEV1 NEV2
ASCII
GRID
S1
D
AIR
RTU
M1
AIR
B
C
ZOT
MOTOR
6V DC
230V AC
HRS
RS
L N
NL
EKRTCTRL2
5.3
5.4
EN
To position the temperature probe (ref. A):
- pass the probe through the hole on the shoulder (ref. B)
- insert the probe into the lower hole (ref. C)
- fix the probe on the relevant hook (ref. D)
Air temperature probe assembly
EKRTCTRL2 Connections
H2* water temperature probe (10 kΩ)
AIR air temperature probe (10 kΩ)
M1 DC inverter fan motor
S1 grill safety micro-switch
Y1
water solenoid valve (230V/ 50Hz 1A output
voltage)
Y2
Mobile flap connection.
230V/ 50Hz 1A output voltage.
L-N
230V/50Hz electrical power supply
* If after switching the power on the board
detects the H2 probe, start-up occurs in normal
conditions with the minimum water temperature
when heating (30°C) and maximum when
cooling (20°C).
The board also has a function when there is no
probe, in such cases the fan stop minimum and
maximum thresholds are ignored.
Содержание
- Daikin altherma 1
- Heat pump convector options 1
- Installation manual 1
- By following the suggestions contained in this manual the product you have purchased will operate without problems giving you optimum room temperatures with minimum energy costs 2
- Daikin europe n v 2
- Symbols 2
- We are sure you will be happy with it because it represents the state of the art in the technology of home air conditioning 2
- We would first of all like to thank you for having chosen one of our products 2
- General 4
- General warnings 4
- Assembly 5
- Assembly set up and connection of on board control panels 5
- Close the box with the 4 screws ref h 5
- Connect the electrics tidy cables and fix them with the three clevises supplied ref g 5
- Connect the water probe to the h2 connector on the device 5
- Connected 5
- Ekrtctrl1 5
- For versions with hydraulic connections on the right refer to the relevant paragraph 5
- Place the screw head covers in their housing on the control panel 5
- Refit the vanity plate on the side of the unit 5
- Slide the control panel into its housing in the upper part of the device and fix it with the two fixing screws ref a to install the connection box 5
- The board also has a function when there is no water probe in such cases the fan stop thresholds are ignored 5
- The regulation also works without a water probe 5
- The water temperature probe controls the temperature inside the batteries and determines when the fan starts according to pre set parameters minimum operation in winder and maximum in summer check that they are correctly inserted into the compartment on the battery 5
- Tighten the upper screws on the control panel 5
- Cp presence contact input connection only for ekrtctrl1 6
- Set up of auxiliary dip switch functions b and c 6
- Air temperature probe assembly only for ekrtctrl1 7
- Ekrtctrl1 8
- Ekrtctrl1 connections 8
- Continuous modulation circuit board for connecting remote thermostat 9
- Ekwhctrl0 9
- Error signals 9
- Led indications ref a 9
- Ekwhctrl0 10
- Ekwhctrl0 connections 10
- Ekwhctrl1 11
- Wall mounted remote control panel assembly ekwhctrl1 11
- Cp occupancy contact input connection 12
- Spring loaded terminal connections ab and cp 12
- Ekwhctrl1 connections 13
- Assembly 14
- Assembly and connections for on board control panel ekrtctrl2 14
- Ekrtctrl2 14
- Air temperature probe assembly 15
- Ekrtctrl2 15
- Ekrtctrl2 connections 15
- Setup menu 16
- Setup menu for ekrtctrl1 ekwhctrl1 ekrtctrl2 setup menu for ekrtctrl1 ekwhctrl1 ekrtctrl2 16
- Adjust the value in a range of 9 c to 12 c at 17
- Adjusting the brightness of the display 17
- After 30 seconds from the last action the control goes 17
- Cc cooling close 17
- Co cooling open 17
- Cp clean contact default 17
- Display operation 17
- Factory reset 17
- Increase and decrease the brightness with the icons 17
- Off and the settings is memorised 17
- Probe t regulation offset room temperature probe 17
- Select no to keep the current settings 17
- Select ys to reset the settings 17
- Settings of the digital input 17
- The adjustment range is from 9 to 12 17
- The brightness adjustment range is from 00 to 01 17
- Variations of 0 1 c 17
- Sensor offset settings humidity probe 18
- Assembly 19
- Assembly and connections for on board control panel ekpcbo 19
- Ekpcbo 19
- Ekpcbo 20
- Ekpcbo connections 20
- Warnings table 20
- Ekrtctrl1 ekrtctrl2 21
- Motor connection in versions with hydraulic connections on the right ekreplh 21
- Versions with connections on the right 21
Похожие устройства
- Daikin EKRTCTRL2 Инструкция по эксплуатации
- Daikin EKRTCTRL2 Инструкция по монтажу
- Daikin EKWHCTRL0 Инструкция по эксплуатации
- Daikin EKWHCTRL0 Инструкция по монтажу
- Daikin EKWHCTRL1 Инструкция по эксплуатации
- Daikin EKWHCTRL1 Инструкция по монтажу
- Whirlpool MT 225 Service Manual
- Whirlpool MT 225 Устройство и электрические схемы
- Whirlpool MT 225 Основные компоненты СВЧ печи
- Whirlpool MT 245 Service Manual
- Whirlpool MT 245 Устройство и электрические схемы
- Whirlpool MT 245 Основные компоненты СВЧ печи
- Daikin EXTENSIONZONEA Инструкция по монтажу
- Daikin FWXT10AATV3 Инструкция по эксплуатации
- Daikin FWXT15AATV3 Инструкция по эксплуатации
- Daikin FWXT20AATV3 Инструкция по эксплуатации
- Alpine SWD-2000 Руководство пользователя
- Alpine SPX-17MB Руководство пользователя
- Alpine SPX-177R Руководство пользователя
- Alpine SPX-137R Руководство пользователя