![Hyundai H-SA1004 Red [3/15] Before you start](/img/pdf.png)
Hyundai H-SA1004 Red [3/15] Before you start
![Hyundai H-SA1004 Red [3/15] Before you start](/views2/1080123/page3/bg3.png)
3
Before you start
• Do not run wiring underneath or outside
the car since exposure to the elements may
cause the insulation to deteriorate rapidly,
resulting in short-circuits and/or intermittent
operation.
• All cables should be run beneath carpets
and inside trim pieces.
• To help minimize interference, it is best to
run the power cables along the opposite side of
the audio (RCA) cables.
• Whenever wires pass through metal,
rubber or plastic grommets must be used to
prevent the metal from wearing through the
installation and causing a short.
• Whenever possible, use cable ties,
mounting clamps and similar wiring aids.
(available from an electrical supply or auto parts
store) Adding stress relief loops to wiring is also
advisable to prevent straining or breakage.
• It is best to test the system before the
amplifier is mounted and interior of car is
reassembled.
• If the temperature inside your car reaches
extreme levels(such as by sitting locked up
for several hours in the hot sun or exposed to
a very cold winter's day) the amplifier may go
into protection mode and shut off. Leave the
unit off until the ambient temperature returns
to normal.
• The amplifier operates with any vehicle
using a 12 volt negative ground system. If you
are not sure of the type of electrical system in
your vehicle, consult your authorized dealer or
qualified mechanic.
• Never ground the speaker leads and never
allow the speaker leads to come in contact
with each other. The Speaker wire should be at
least 16 gauge or lower.
• Remote turn on wire must be switched by
the radio. If the radio does not have a remote
turn on or antenna output, connect to wire that
has a positive 12 volts output when the key is
turned to the accessory position. If the amplifier
does not turn off the battery will die.
• Do not listen to high volumes for extended
periods of time or hearing damage may occur.
Continuous exposure to sound
pressure levels over 100 dB may cause
permanent hearing loss. High-powered
autosound system may produce soundn
pressure levels well over 130 dB. Use common
sense and practice safe sound.
Содержание
- Before you start 2
- Dear customer 2
- Important safeguards 2
- Utilization of the product 2
- Before you start 3
- Connection 4
- Installation 4
- Installation connection 4
- Power connection 4
- Channel bridged mode configuration 5
- Channel stereo configuration 5
- Installation connection 5
- Speaker connection 5
- This amplifier can operate in one two three or four channel mode the minimum impedance for single channel bridged operation is 4 or 8 ohms mono operation 2 4 ohm tri channel power is referred to stereo and mono at the same time minimum impedance remains the same for three channel front subwoofer systems when proper passive crossovers are 5
- Used connect right and left speaker wire to corresponding speaker output terminals of the amplifier be sure to have the positive wire from the speaker connected to the positive speaker terminal of the amplifier and the negative wire from the speaker must connect with the negative terminal of the amplifier reversing any of the connections will result in the speaker cones moving out of phase which causes bass cancellation 5
- Adjustment 6
- Installation connection 6
- General information 7
- Troubleshooting 7
- Accessories 8
- General information 8
- Specifications 8
- Меры предосторожности 9
- Перед началом эксплуатации 9
- Уважаемый покупатель 9
- Утилизация изделия 9
- Перед началом эксплуатации 10
- Подключение 11
- Подключение питания 11
- Установка 11
- Установка подключение 11
- Канальный мостовой режим 12
- Канальный режим 2 мостовой 12
- Канальный стереорежим 12
- Ом строго соблюдая полярность подклю чите провода правого и левого динамиков к соответствующим разъемам усилителя при неправильной полярности динамики бу дут работать в противофазе что приведет к гашению низких частот басов 12
- Подключение динамиков 12
- Установка подключение 12
- Этот усилитель может работать в режимах от одного до четырех каналов минимальная нагрузка при работе на одном канале при мостовом подключении составляет 4 8 ом при монорежиме 2 4 12
- Настройки 13
- Управление устройством 13
- Общая информация 14
- Руководство по устранению неисправностей 14
- Аксессуары 15
- Общая информация 15
- Технические характеристики 15
Похожие устройства
- Prology DVS-260 Инструкция по эксплуатации
- Bomann HLO 2280 CB Инструкция по эксплуатации
- Rolsen MG1770SA Инструкция по эксплуатации
- Prology DVU-1500 Инструкция по эксплуатации
- Bomann KW 1413 CB Инструкция по эксплуатации
- Rolsen MG1770SN Инструкция по эксплуатации
- Bomann KW 1421 CB Инструкция по эксплуатации
- Rolsen MG1770T Инструкция по эксплуатации
- Jabra Active Stereo Black Инструкция по эксплуатации
- Bomann KW 1420 CB Инструкция по эксплуатации
- Jabra Active Stereo Wh Инструкция по эксплуатации
- Bomann KW 1416 CB Инструкция по эксплуатации
- Rolsen MG2180M Инструкция по эксплуатации
- Bomann KW 1415 CB Инструкция по эксплуатации
- Jabra Active Stereo Y Инструкция по эксплуатации
- Rolsen MG2180S Инструкция по эксплуатации
- Bomann KW 1411 CB Инструкция по эксплуатации
- Rolsen MG2180T Инструкция по эксплуатации
- Bomann KM 379 CB Инструкция по эксплуатации
- Rolsen MG2380M Инструкция по эксплуатации
Скачать
Случайные обсуждения