Haier HSU-09C03/U(ZXF) [6/107] Caution
![Haier HSU-12C03/U(ZXF) [6/107] Caution](/views2/1808706/page6/bg6.png)
3
Domestic Air Conditioner
Warning
Be sure to use an exclusive power circuit for the equipment, and follow the technical standards related to
the electrical equipment, the internal wiring regulations and the instruction manual for installation when
conducting electrical work.
Insufficient power circuit capacity and improper electrical work can cause an electrical shock or fire.
Be sure to use the specified cable to connect between the indoor and outdoor units. Make the
connections securely and route the cable properly so that there is no force pulling the cable at the
connection terminals.
Improper connections can cause excessive heat generation or fire.
When connecting the cable between the indoor and outdoor units, make sure that the terminal cover does
not lift off or dismount because of the cable.
If the cover is not mounted properly, the terminal connection section can cause an electrical shock,
excessive heat generation or fire.
Do not damage or modify the power cable.
Damaged or modified power cable can cause an electrical shock or fire. Placing heavy items on the
power cable, and heating or pulling the power cable can damage the cable.
Do not mix air or gas other than the specified refrigerant (R-410A / R22) in the refrigerant system.
If air enters the refrigerating system, an excessively high pressure results, causing equipment damage
and injury.
If the refrigerant gas leaks, be sure to locate the leak and repair it before charging the refrigerant. After
charging refrigerant, make sure that there is no refrigerant leak.
If the leak cannot be located and the repair work must be stopped, be sure to perform pump-down and
close the service valve, to prevent the refrigerant gas from leaking into the room. The refrigerant gas itself
is harmless, but it can generate toxic gases when it contacts flames, such as fan and other heaters,
stoves and ranges.
When replacing the coin battery in the remote controller, be sure to disposed of the old battery to prevent
children from swallowing it.
If a child swallows the coin battery, see a doctor immediately.
Caution
Installation of a leakage breaker is necessary in some cases depending on the conditions of the
installation site, to prevent electrical shocks.
Do not install the equipment in a place where there is a possibility of combustible gas leaks.
If a combustible gas leaks and remains around the unit, it can cause a fire.
Be sure to install the packing and seal on the installation frame properly. If the packing and seal are not
installed properly, water can enter the room and wet the furniture and floor.
For
integral
units only
HSU-09,12H03/U(ZXF) Introduction
Содержание
- On off 1
- Caution in repair 4
- Introduction 4
- Safety cautions 4
- Warning 4
- Cautions regarding products after repair 5
- Domestic air conditioner 5
- Hsu 09 12h03 u zxf introduction 5
- Warning 5
- Caution 6
- Domestic air conditioner 6
- Hsu 09 12h03 u zxf introduction 6
- Warning 6
- Caution 7
- Domestic air conditioner 7
- Hsu 09 12h03 u zxf introduction 7
- Inspection after repair 7
- Warning 7
- Domestic air conditioner 8
- Hsu 09 12h03 u zxf introduction 8
- Icon type of information description 8
- Icons are used to attract the attention of the reader to specific information the meaning of each icon is described in 8
- The table below 8
- Using icons 8
- Using icons list 8
- Functions and control 14
- Hsu 09 12 h03 u zxf functions and control 14
- Main functions and control specifications 14
- Hsu 09 12 h03 u zxf functions and control 15
- Hsu 09 12 h03 u zxf functions and control 16
- Minutes 16
- Hours t 1 hour ts 2 ts 1 1 hours 17
- Hsu 09 12 h03 u zxf functions and control 17
- Off t hour 17
- T ts 3hours 3hours ts 2 ts 3 ts 4 1 hour 17
- Timer function 18
- Function of main thermistor 19
- B25 50 4200k 3 20
- Domestic air conditioner 20
- Hsu 09 12 h03 u zxf functions and control 20
- R25 23k 3 20
- Room sensor 20
- Value of thermistor 20
- Domestic air conditioner 21
- Hsu 09 12 h03 u zxf functions and control 21
- Domestic air conditioner 22
- Hsu 09 12 h03 u zxf functions and control 22
- Domestic air conditioner 23
- Hsu 09 12 h03 u zxf functions and control 23
- B25 50 3700k 3 24
- Domestic air conditioner 24
- Hsu 09 2h03 u zxf 24
- Pipe sensor 24
- R25 10k 3 24
- Domestic air conditioner 25
- Hsu 09 2h03 u zxf 25
- Domestic air conditioner 26
- Hsu 09 2h03 u zxf 26
- Domestic air conditioner 27
- Hsu 09 2h03 u zxf 27
- System configuration 28
- Cautions 29
- Contain no fluorochloric hydrocarbon 29
- Disposal of the old air conditioner 29
- Disposal of the packaging of your new air conditioner 29
- Instruction 29
- Safety instructions and warnings 29
- Cautions 30
- Specifications 30
- The machine is adaptive in following situation 30
- Caution 31
- Cautions 31
- Installation 31
- Safety instruction 31
- Warning 31
- Caution 32
- Cautions 32
- Domestic air conditioner 32
- Hsu 09 12h03 u zxf system configuration 32
- Warning 32
- Domestic air conditioner 33
- Hsu 09 12h03 u zxf system configuration 33
- Indoor unit 33
- Outdoor unit 33
- Parts and functions 33
- Parts and functions 34
- Parts and functions 35
- Health operation 36
- Operation 36
- Remote controller 36
- Auto operation 37
- Fan speed selection 37
- Operation 37
- Remote controller 37
- Select operation mode 37
- Select temp setting 37
- Unit start 37
- Unit stop 37
- Cool operation 38
- Fan speed selection 38
- Operation 38
- Remote controller 38
- Select operation mode 38
- Select temp setting 38
- Unit start 38
- Unit stop 38
- Dry operation 39
- Fan speed selection 39
- Operation 39
- Remote controller 39
- Select operation mode 39
- Select temp setting 39
- Unit start 39
- Unit stop 39
- About fan operation 40
- Fan operation 40
- Fan speed selection 40
- Operation 40
- Remote controller 40
- Select operation mode 40
- Unit start 40
- Unit stop 40
- Fan speed selection 41
- Heat operation 41
- Operation 41
- Remote controller 41
- Select operation mode 41
- Select temp setting 41
- Unit start 41
- Unit stop 41
- Air flow direction adjustment 42
- For each press of button air flow direction on remote controller displays as follows according to different operation modes 42
- For each press of button remote controller displays as follows remote controller 42
- Left and right air flow direction 42
- Operation 42
- Remote controller 42
- Remote controller cool dry fan 42
- Status display of air sending 42
- The horizontal louvers will swing according to the above positions note when restart after remote turning off the remote controller will automatically memorize the previous set swing position 42
- The vertical flap will swing according to the above positions 42
- Up and down air flow direction 42
- Domestic air conditioner 43
- Hsu 09 12h03 u zxf system configuration 43
- Operation 43
- Remote controller 43
- Sleep operation 43
- Cancel timer mode 44
- Confirming your setting 44
- Operation 44
- Remote controller 44
- Time setting 44
- Timer on off operation 44
- Operation 45
- Remote controller 45
- Timer on off operation 45
- In power operation status 46
- Operation 46
- Power operation 46
- Power soft operation 46
- Remote controller 46
- Selecting of soft operation 46
- Soft operation 46
- To cancel power operation 46
- To cancel soft operation 46
- Health airflow operation 47
- Operation 47
- Press on off to starting 47
- Remote controller 47
- The cancel of the health airflow function 47
- The setting of health airflow function 47
- Emergency and test operation 48
- Emergency operation 48
- Operation 48
- Removal of the restriction of emergency or test operation 48
- Test operation 48
- Close doors and windows during operation 49
- Do not block the air inlet or outlet 49
- For smart use of the air conditioner 49
- If the unit is not to be used for a long time turn off the power supply main switch 49
- Maintenance 49
- Setting of proper room temperature 49
- Use the louvers effectively 49
- Use the timer effectively 49
- Air filter cleaning 50
- Attach the filter 50
- Clean the filter 50
- Close the inlet grille 50
- Do not use the following for cleaning 50
- For smart use of the air conditioner 50
- Indoor body 50
- Maintenance 50
- Open the inlet grille by pulling it upward 50
- Remote controller 50
- Remove the filter 50
- Warning 50
- Attach old air purifying filter 51
- Attach the standard air filter 51
- Close the inlet grille 51
- Common sense 51
- Detach old air purifying filter 51
- Detach the standard air filter 51
- Maintenance 51
- Open the lnlet grille 51
- Replancement of air purifying filter 51
- Maintenance 52
- To keep your air conditioner in good condition after season 52
- Before setting in high season 53
- Caution 53
- Cleaning the standard air filter 53
- Connecting the earthing cable 53
- Do not block the air inlet or outlet 53
- Earthing 53
- Maintenance 53
- No wet hand 53
- Plug in 53
- Before asking for service check the following first 54
- Trouble shooting 54
- Cautio 56
- Correct the connection 56
- E1 room temperature sensor failure e2 indoor heat exchange sensor failure 56
- Troubleshooting 56
- E e e 4 4 4 57
- Fan motor ac motor or related abnormality 57
- Indoor eeprom error 57
- Domestic air conditioner 58
- Hsu 09 12h03 u zxf service diagnosis 58
- Troubleshooting 58
- Drawing for the installation of indoor and outdoor units 59
- H03 u zxf 59
- Installation 59
- Necessary tools for installation 59
- Fix the unit to concrete or block with bolts 10mm and nuts firmly and horizontally when fitting the unit to wall surface roof or rooftop fix a supporter surely with nails or wires in consideration of earthquake and strong wind 60
- Fixing of outdoor unit 60
- Floor fixing dimensions of the outdoor unit unit mm 60
- Freshair 3 freshair 2 hsu 09h03 u zxf hsu 12h03 u zxf 60
- H03 u zxf 60
- Hsu 09c03 u zxf hsu 12c03 u zxf 60
- Hsu 18c03 u zxf 60
- If vibration may affect the house fix the unit by attaching a vibration proof mat 60
- Indoor unit 60
- Outdoor unit 60
- Power source 60
- Selection of installation place 60
- Selection of pipe 60
- Carry out based on the neighboring pillars or lintels the mounting plate must be fixed horizontally otherwise condensed water may overflow the water container then temporarily fasten the plate with one steel nail 2 make sure once more the proper level of the plate by hanging a thread with a weight from the central top of the plate then fasten securely the plate with the attachment steel nail 3 find the wall hole location a using a measuring tape 61
- Drawing of pipe 61
- Fitting of the mounting plate and positioning of the wall hole 61
- Fix to side bar and lintel a mounting bar which is separately sold and then fasten 61
- Indoor unit 61
- Installation of the indoor unit 61
- Left left rear piping 61
- Making a hole on the wall and fitting the piping hole cover 61
- Rear piping 61
- Refer to the previous article when the mounting plate is first fixed for the position of wall hole 61
- The plate to the fixed mounting bar 61
- When the mounting plate is first fixed 61
- When the mounting plate is fixed side bar and lintel 61
- Connecting the indoor outdoor electric cable 62
- Fixing the indoor unit body 62
- Indoor unit 62
- Removing the wiring cover 62
- When connecting the cable after installing the indoor unit 62
- When connecting the cable before installing the indoor unit 62
- Easily demount cleaning of indoor unit 63
- Indoor unit 63
- Installation instruction on the indoor part of the fresh air device optional 63
- See the installation from the fresh air sets for the installation of outdoor unit 63
- Attaching drain elbow 64
- Connection 64
- Connection of pipes 64
- H03 u zxf 64
- Half union flare nut 64
- Installation of outdoor unit 64
- Outdoor unit 64
- Spanner torque wrench 64
- Flare nut 65
- Outdoor unit 65
- Purging method 65
- Check for installation and test run 66
- Check items for test run 66
- Correct incorrect 66
- Cutting and flaring work of piping 66
- Flare tooling die 66
- On drainage 66
- Pipe cutting is carried out with a pipe cutter and burs must be removed after inserting the flare nut flaring work is carried out 66
- Please install the drain hose so as to be downward slope without fail please don t do the drainage as shown below 66
- Please kindly explain to our customers how to operate through the instruction manual 66
- Please pour water in the drain pan of the indoor unit and confirm that drainage is carried out surely to outdoor in case that the attached drain hose is in a room please apply heat insulation to it without fail 66
- Power source installation 66
- The power source must be exclusively used for air conditioner over i0a in the case of installing an air conditioner in a moist place please install an earth leakage breaker for installation in other places use a circuit breaker as far as possible 66
- Fresh air pipe 1 full energy recovery exchanger 67
- Packing list 67
- Refresh system installation manual 67
- Bend connector 68
- Full energy recovery exchanger 68
- Room air pipe 68
- According to the drawing install the full energy recovery exchanger on the corresponding place of the outdoor unit and fix the fittings on the outdoor unit cover with the screws 69
- Fixation screw 69
- Fresh air exit 69
- Fresh air filter 69
- Fresh entrance 69
- Installation manual 69
- Outdoor unit 69
- Room air entrance connect room air pipe 69
- Room air exit 69
- The main unit installation 69
- Pipeline installation 70
- Small size outdoor unit installation sketch 70
- Caution 71
- Grouding block 71
- Power block installation 71
- Power phase string and c o n t r o l i n g b l o c k w i t h pyrocondensation jacket pipe 71
- Pyroshrink insulation jacket 71
- There are two terminal blocks f and g on the full energy recovery exchanger f block is power phase string and controlling block which connects with power string g block is the ground connecting block which connects the zero string end in the terminal box 71
- There is anti water jacket pyroshrink pipe on the block connector of the controling string and the power phase string please confirm whether it is fastened after connecting 71
- Indoor unit 72
- Installation of indoor unit 72
- 0 outdoor panel 94
- Appendix 104
- Hsu 09 12 h03 u zxf appendix 104
- Piping diagrams 104
Похожие устройства
- Haier HSU-12C03/U(ZXF) Инструкция по монтажу
- Haier HSU-12C03/U(ZXF) Инструкция по эксплуатации
- Haier HSU-12C03/U(ZXF) Сервис мануал
- Haier HSU-18C03/U(ZXF) Инструкция по монтажу
- Haier HSU-18C03/U(ZXF) Инструкция по эксплуатации
- Haier HSU-18C03/U(ZXF) Сервис мануал
- Haier HBU-18CC03 Инструкция по эксплуатации
- Haier AB182ACMCA Инструкция по эксплуатации
- Haier AU182AFMCA Инструкция по эксплуатации
- Haier HBU-18HC03 Инструкция по эксплуатации
- Haier HBU-18HC03 Сервис мануал
- Feron CL592 (41643) Инструкция по эксплуатации
- Feron CL592 (41643) Презентация
- Feron CL590 (41635) Инструкция по эксплуатации
- Feron CL590 (41635) Презентация
- Feron CL574 (41652) Инструкция по эксплуатации
- Feron CL574 (41652) Презентация
- Feron CL572 (41647) Инструкция по эксплуатации
- Feron CL572 (41647) Презентация
- Feron CL572 (41648) Инструкция по эксплуатации