Haier HWF10DW1 [12/13] General information and tips
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Haier HWF10DW1 [12/13] General information and tips

Haier HWF10DW1 [12/13] General information and tips
2322
Troubleshooting Troubleshooting
In case of power failure
The current programme and its setting will save. When
power supply is restored operation will resume . To
cancel it, touch “Start/Pause“ and then “Power“ for
about 3 sec. If there is a power failure during a wash
cycle your washer will stop and the door will remain
locked. You can unlock the washer door to remove
your clothes by pening the pump filter cover at the
bottom right of your washer. Simply place a coin or
flathead screwdriver in the slot of the cover and slide it
sidewards, then pull the door release tab. Do not
attempt to do this if the water level in the washer is
above the level of the door. When power is restored
you will need to restart your machine by simply
pressing the POWER button. The washer
will
remember where in the cycle it was up to. to advise the
meaning of the content.
Troubleshooting without displ ay code
Problem Cause Solution
Washing machine
fails to operate
1. Power failure
2. Machine hasn’t been seitched
on.
3. Door is not properly closed.
4. Programme is not yet started
1. Check power supply.
2. Switch the machine on.
3. Close the door p roperly.
4. Press “START/PAUSE”
button.
Washing machine
will not fill with
wate.
1. No water
2. Inlet hose is kin ked.
3. Inlet hose fil ter is blocked.
4. Water pressure is less than
0.03Mpa.
5. Door is not properly closed.
6. Water supply failure.
1. Check water tap.
2. Check in let hos e.
3. Unblock inlet hose fil ter.
4. Check water pressure.
5. Close the door p roperly.
6. Ensure the water supply.
Machine is
draining while
being filled.
1. Height of d rain hose is below
80cm.
2. Drain hose end could reach
into water.
1. Make sure that drain hose is
properly installed.
2. Make sure the drain hose is
not in water.
Drainage failure.
1. Drain hose is bloc ked.
2. Pump filter is blocked.
3. Drain hose end is higher than
100cm above floor level.
1. Unblock drain hose.
2. Clean pump filter.
3. Make sure that drain hose is
properly installed.
Problem Cause Solution
Strong vibration
while spinning.
1. Not all t ransportation bolts
have been removed.
2. Appliance has no solid
position.
3. Machine load is not correct.
1. Remove all transportation
bolts.
2. Ensure solid ground and
a levelled position.
3. Check load weight and
balance.
Operation stops
for a period of
time.
1. Applian ce displays error code.
2. Problem due to load pattern.
3. Programme performs soaking
cycle.
1. Consider displ ay codes.
2. Reduce or adjust load.
3. Cancel programme and
restart.
Operation stops
before completi-
ng wash cycle.
Water or electric failure.
Check power and water
supply.
Excessive foam
floats drum and/or
detergent drawer.
1. Detergent is not a appropriate.
2. Excessive use of detergent in
manually dosage.
1. Check detergent recom-
mendations.
2. Reduce amount of dete-
rgent.
Spinning fails Unbalance of laundry. Check machine load.Run the
Spin programme again.
General information and tips:
If too much foam is visible during spin cycle, the motor will stop and drain
pump will activate for 90 seconds. If that elimination of foam fails up to 3
times, programme ends without spinning.
Automatic adjust-
ment
Washing programme
This is normal and doesn‘t
of washing
duration will be adjusted. aff ect functionality.
time

Содержание

Похожие устройства

Скачать