![Haier AC092FEBHA [11/12] Settings of heating temperature compensation usage of switch sw03](/img/pdf.png)
Haier AC092FEBHA [11/12] Settings of heating temperature compensation usage of switch sw03
![Haier AC322FEAHA [11/12] Settings of heating temperature compensation usage of switch sw03](/views2/1822091/page11/bgb.png)
10
Finishing and amendment
Wires (cables between power supply and air conditioner) MUST keep clear of valves in gas
side of distribution tube and distribution tubewithout heatproof materials.
Melting of wire skin can cause electric shock, leakage and fire hazard.
1.Wrap tapes on distribution tube of refrigerant, wires in air conditioner room and drainage pipe
after finishing these engineering.
2.Fix them on the wall with supporting frame after wrapping tapes.
3.Control wire should be fixed on distribution tube which is wrapped by heatproof materials.
Improve efficiency of cooling and heating
Adjust wind direction
Requirement
Donít handle horizontal swing leaves manually to prevent defect ouccring.
Refer to ìoperation manualî to know how to operate.
To upward or downward directions, adjust swing leaves of horizontal orientation. To prevent
short cut of air flow, horizontal leaves can only swing within a certain range.
Settings of heating temperature compensation (usage of switch SW03)
Enhance air circulation with other equipment and make hot air near the ceiling blow downward.
Poor heating effect due to reasons such as installation position of indoor subassembly and room
structure can be changed in the following way to amend heating temperature.
<How to adjust>
There is code switch SW03 on PC board of indoor assembly. Adjust TA (temperature amendment)
as the following table.
Usage of emergency switch (usage of switch SW04)
(SW03)
Position of code swith
(restricted to position
1and 2 only)
Setting before
leaving factory
Increased value of
temperature
For trial run of indoor blower fan after finishing installation,
dial code of emergency switch (SW04) to ìONî side.
Ability setting of indoor subassembly (Usage of switch SW05)
Default ability of indoor subassembly has been set well
before leaving factory. It can be set according to ability
of indoor subassembly after changing circuit board.
Relation between ability setting and combination of
ON/OFF switches is as following table:
Ability setting SW05.
1 2 3 4
Note: O:ON X:OFF
Power
setting
Set
power
!
Notice
2
Содержание
- Safety precautions 2
- Notice 3
- Selection of installation place 3
- Installation in under ceiling 4
- Installation of air conditioner 4
- Installation of suspending bolts 4
- Prior to installation 4
- Directly use angle iron to set supporting angle iron use inlet hinge joint inlet plug or inlet bolt 5
- Fasten hexagon bolt and fix the air conditioner 5
- Insert hexagon bolt into carved fillet 5
- Install beam wood on the girder and set suspending bolts 5
- Installation of air conditioner 5
- Installation of air conditionert 5
- Installation of attached hexagon bolt 5
- Installation position of suspending bolts 5
- Installation status of supporting frame 5
- Internal suspension ac092 122 142 162feaha ac092 122 142 162febha 5
- Internal suspension ac182 242 282feaha ac182 242 282febha 5
- Please refer to positions of suspending bolts printed on installation paste board of ac092 122 142 162feaha ac092 122 142 162febha type 5
- Steel structure old concrete building 5
- Wood building new concrete building 5
- Installation of floor console 6
- Refrigerant distribution tube 7
- Requirentents 8
- Undulation 8
- Electric wiring 9
- Remote controller wire 9
- Code switch aw02 on base board of indoor unit has the function of setting centralized control address group number group number can be set by changing ì on offî status in ì 1 6î code positions code switch sw02 and its dialing codes are shown as following diagram 10
- One set of remote controller can control a group of 16 indoor unit at the most refer to electrical wiring layout items for wiring layout between indoor unit arrange wires between remote controller and indoor unit according to the following sequence 1 set number setting switch sw01 on pc board of each indoor unit with number 1 as ì 1î number 2 as ì 2î ö ö the machine directly connecting remote controller must be set as number 1î number 1 is the host while others are subsidiaries 2 connect terminals a b c of the remote controller with that of number 1 indoor unit respectively according to same numbers 3 connect terminals b c of number 1 indoor unit with that of number 2 respectively according to same numbers 4 connect terminals b c of number 2 indoor unit with that of number 3 respectively according to same numbers 5 by analogy of the above stop until connecting to terminals b c of number 16 at the maximum 6 disassemble short connection wire to cn12 terminal on control base board of numb 10
- Operation control 10
- Relation between combination of ì on offî status in ì 1 6î code positions and group number are shown as in right table when ì 7î position of sw02 is in ì offî status group number can be set either by dialing codes on sw02 or with circuit controller while ì 7î position of sw02 is in ì onî status group number can only be set either by dialing codes on sw02 10
- Requirement 10
- Setting of group number of indoor subassemblies 10
- Solution of group control 10
- Wires of remote controller between indoor unit should be power cord more than 1mm with length less than 500 m total length from remote controller to number 16 machine 10
- Settings of heating temperature compensation usage of switch sw03 11
- Usage of emergency switch usage of switch sw04 11
- Disorders in trial run 12
- Notice 12
- Requirement 12
- Trial run 12
Похожие устройства
- Haier AC092FEBHA Инструкция по эксплуатации
- Haier AC122FEAHA Инструкция по монтажу
- Haier AC122FEAHA Инструкция по эксплуатации
- Haier AC122FEBHA Инструкция по монтажу
- Haier AC122FEBHA Инструкция по эксплуатации
- Haier AC162FEAHA Инструкция по монтажу
- Haier AC162FEAHA Инструкция по эксплуатации
- Haier AC162FEBHA Инструкция по монтажу
- Haier AC162FEBHA Инструкция по эксплуатации
- Haier AC182FEAHA Инструкция по монтажу
- Haier AC182FEAHA Инструкция по эксплуатации
- Haier AC182FEBHA Инструкция по монтажу
- Haier AC182FEBHA Инструкция по эксплуатации
- Haier AC242FEAHA Инструкция по монтажу
- Haier AC242FEAHA Инструкция по эксплуатации
- Haier AC242FEBHA Инструкция по монтажу
- Haier AC242FEBHA Инструкция по эксплуатации
- Haier AC282FEAHA Инструкция по монтажу
- Haier AC282FEAHA Инструкция по эксплуатации
- Haier AC282FEBHA Инструкция по монтажу