Citizen CMP-30II — управление режимами печати: инициализация и переворот [23/71]

Содержание

• Model cmp 30 series p.1
• Mobile thermal printer p.1
• Esc command manual p.1
• Table of contents p.2
• Command function p.4
• Command notation p.6
• Command description p.6
• B is binary p.6
• H is hexadecimal p.6
• Width 1 the printer executes print buffer full printing of the current line and p.7
• This command sets the print position to the beginning of the line p.7
• This command is ignored unless the next tab position has been set p.7
• The printing position to printing area width 1 p.7
• The default setting of the horizontal tab position for the paper roll is font p.7
• Spacing p.7
• Prints the data in the print buffer and feeds one line based on the current line p.7
• Print and line feed p.7
• Moves the print position to the next tab position p.7
• If this command is received when the printing position is at printing area p.7
• If the next horizontal tab position exceeds the printing area the printer sets p.7
• Horizontal tab processing from the beginning of the next line p.7
• Horizontal tab positions are set using esc d p.7
• Commands p.7
• A 12 x 24 every 8th character 9th 17th 25th column p.7
• When automatic line feed is enabled this command functions the same as p.8
• This command sets the print position to the beginning of the line p.8
• This command is enabled only in page mode p.8
• The printing area set by esc w is reset to the default setting p.8
• The printer does not execute paper cutting p.8
• The currently specified printable area it is deleted p.8
• The buffer data is deleted after being printed p.8
• The automatic line feed is ignored p.8
• Sets the print starting position to the beginning of the line p.8
• Prints the data in the print buffer and returns to standard mode p.8
• Lf when automatic line feed is disabled this command is ignored p.8
• In page mode delete all the print data in the current printable area p.8
• If data that existed in the previously specified printable area also exists in p.8
• This command is executed even when the printer is offline the receive p.9
• Byte data p.9
• The printer transmits the status without confirming whether the host p.9
• Buffer is full or there is an error status p.9
• The printer transmits the current status each status is represented by one p.9
• According to the following parameters p.9
• The printer executes this command upon receiving it p.9
• Status transmitted by the dle eot command and the asb status must be p.9
• Real time status transmission p.9
• N 7 cancel card reader mode p.9
• N 5 msr status request p.9
• N 4 transmit paper roll sensor status p.9
• N 3 transmit error status p.9
• N 2 transmit off line status p.9
• N 1 transmit printer status p.9
• N 1 printer status p.9
• Dle eot p.9
• When auto status back asb is enabled using the gs a command the p.9
• Differentiated p.9
• Transmits the selected printer status specified by n in real time p.9
• Computer can receive data p.9
• To recover p.10
• Recover by correcting the cause of the error and executing dle enq n 1 n p.10
• Printing stops p.10
• Print head temperature drops sufficiently or when the paper roll cover is open p.10
• N 3 error status p.10
• N 2 off line status p.10
• Bit 6 when printing is stopped due to high print head temperature until the p.10
• Bit 5 becomes on when the paper end sensor detects paper end and p.10
• Bit 3 if these errors occur due to paper jams or the like it is possible to p.10
• 2 if an error due to a circuit failure e g wire break occurs it is impossible p.10
• N 5 msr status request p.11
• N 4 continuous paper sensor status p.11
• Mode ms read mode p.11
• During printing bit 6 is on p.11
• Selected card reader p.11
• Read ms p.11
• N 7 if printer is in ms read mode it becomes normal mode and doesn t p.11
• N 7 continuous paper sensor status p.11
• N 5 the data from printe are as follows p.11
• This command is executed even when the printer is offline the receive buffer p.12
• This command is effective only when an auto cutter error occurs p.12
• The printer starts processing data upon receiving this command p.12
• Responds to a request from the host computer p.12
• Real time status transmission p.12
• N specifies the requests as follows p.12
• Is full or there is an error status with a serial interface model p.12
• Dle enq p.12
• 1 n 2 is received p.12
• The right side character spacing for double width mode is twice the normal p.13
• Depending on starting position of the printable area as follows p.13
• The maximum right side spacing is 35 83 mm 255 180 any setting p.13
• After printing the printer does not clear the buffered data setting value for p.13
• Sets the character spacing for the right side of the character to p.13
• Set right side character spacing p.13
• Printable area using esc t the vertical motion unit y is used p.13
• Printable area using esc t the horizontal motion unit x is used p.13
• Normal value p.13
• N x horizontal or vertical motion units p.13
• In standard mode the horizontal motion unit is used p.13
• In page mode the horizontal or vertical motion unit differs in page mode p.13
• In page mode prints all buffered data in the printable area collectively p.13
• ② when the starting position is set to the upper right or lower left of the p.13
• ① when the starting position is set to the upper left or lower right of the p.13
• Exceeding the maximum is converted to the maximum automatically p.13
• When characters are enlarged the right side character spacing is n times p.13
• Esc t and esc w and the position for buffering character data p.13
• This command sets values independently in each mode standard and page p.13
• Esc sp p.13
• This command is enabled only in page mode p.13
• Esc ff p.13
• This command does not affect the setting of characters p.13
• Esc commands p.13
• The line spacing can be set independently in standard mode and in page p.14
• Sets the line spacing to n x vertical or horizontal motion unit inches p.14
• Set line spacing p.14
• Selects approximately 4 3 mm 1 6 spacing p.14
• Select default line spacing p.14
• Position of the printable area p.14
• Line space is equivalent to approximately 4 3 mm 1 6 p.14
• In standard mode the vertical motion until y is used p.14
• In page mode this command function as follows depending on the starting p.14
• Amount of more than 1016 mm 40 is set the printer feeds the paper only p.14
• ② when the starting position is set to the upper right or lower left of p.14
• ① when the starting position is set to the upper left or lower right to p.14
• The printable area using esc t the vertical motion unit y is used p.14
• The printable area using esc t the horizontal motion unit x is p.14
• The maximum paper feed amount is 1016 mm 40 even if a paper feed p.14
• Underline mode can also be turned on or off by using esc note however p.15
• Turns underline mode on or off based on the following values of n p.15
• Turn underline mode on off p.15
• This command does not affect printing p.15
• The printer cannot underline 90 clockwise rotated characters and p.15
• The printer can underline all characters including right side character p.15
• That the last received command is effective p.15
• Spacing but cannot underline the space set by ht p.15
• Mode is turned off does not change the default underline thickness is 1 dot p.15
• Following data is not underlined and the underline thickness set before the p.15
• Changing the character size does not affect the current underline thickness p.15
• White black inverted characters p.15
• When underline mode id turned off by setting the value of n to 0 or 48 the p.15
• Last received command effective p.16
• Hex 1b 21 n p.16
• Gs can also select character size however the setting of the last received p.16
• Format p.16
• Esc e can also turn on or off emphasized mode however the setting of p.16
• Esc can also turn on or off underline mode however the setting of the p.16
• Emphasized mode is effective for alphanumeric and all print modes except p.16
• When some characters in a line are double or more height all the characters p.16
• Details p.16
• When both double height and double width modes are selected quadruple p.16
• Description p.16
• The thickness of the underline is selected by esc regardless of the p.16
• Decimal 27 33 n p.16
• The printer can underline all characters but cannot underline the space set p.16
• Command is effective p.16
• Character size p.16
• The last received command is effective p.16
• By ht or 90 clockwise rotated characters p.16
• Size characters are printed p.16
• Ascii esc n p.16
• Selects print mode s using n as follows p.16
• Select print mode s p.16
• On the line are aligned at the baseline p.16
• Select cancel user defined character set p.17
• ② when the starting position is set to the upper right or lower left of p.17
• Nl 255 p.17
• ① when the starting position is set to the upper left or lower right of p.17
• Nh 255 p.17
• X vertical or horizontal motion unit inches p.17
• N is available only for the least significant bit p.17
• When the user defined character set is canceled the internal character set p.17
• Is automatically selected p.17
• When the lsb of n is 1 the user defined character set is selected p.17
• In page mode the horizontal or vertical motion unit differs depending on the p.17
• Emphasized mode is effective only for alphanumeric p.17
• When the lsb of n is 0 the user defined character set is canceled p.17
• The printable area using esc t the vertical motion unit y is used p.17
• The printable area using esc t the horizontal motion unit x is p.17
• The distance from the beginning of the line to the print position is p.17
• Subsequent characters are to be printed p.17
• Starting position of the printable area as follows p.17
• Settings outside the specified printable area are ignored p.17
• Sets the distance from the beginning of the line to the position at which p.17
• Set absolute print position p.17
• Selects or cancels the user defined character set p.17
• Accommodate the amount of data p.20
• To 0 to not print a dot p.20
• The nl and nh indicate the number of dots of the bit image in the horizontal p.20
• Selects a bit image mode using m for the number of dots specified by nl and p.20
• Select bit image mode p.20
• Required by the data sent with the esc command the following will be p.20
• Processed as normal data p.20
• Performed on the line in question but the printing cannot exceed the p.20
• Nh as follows p.20
• Maximum printable area p.20
• M 0 1 32 33 p.20
• Line the excess data is ignored p.20
• If the width of the printing area set by gs l and gs w less than the width p.20
• If the values of m is out of the specified range nl and data following are p.20
• If the bit image data input exceeds the number of dots to be printed on a p.20
• Direction the number of dots is calculated by nl nh x 256 p.20
• ① the width of the printing area is extended to the right to p.20
• D indicates the bit image data set a corresponding bit of 1 to print a dot or p.20
• This command deletes the pattern defined for the specified code in the font p.22
• This command cancels the pattern defined for the character code specified p.22
• Selected by esc p.22
• If a user defined character has not been defined for the specified character p.22
• For the internal character is printed p.22
• Code the printer ignores this command p.22
• Cancels user defined characters p.22
• Cancel user defined characters p.22
• By n after the user defined character is canceled the corresponding pattern p.22
• Only the lowest bit of n is valid p.23
• Initialize printer p.23
• In upside down printing mode the printer rotates the line to be printed by p.23
• When this command is input in page mode the printer performs only internal p.23
• Flag operations p.23
• When the lsb of n is 1 upside down printing mode is turned on p.23
• Clears the data in the print buffer and resets the printer mode to the mode p.23
• When the lsb of n is 0 upside down printing mode is turned off p.23
• And then prints it p.23
• Turns upside down printing mode on or off p.23
• Turns on off upside down printing mode p.23
• This command is enabled only when processed at the beginning of a line in p.23
• This command does not affect printing in page mode p.23
• The nv bit image data is not cleared p.23
• The macro definition is not cleared p.23
• The data of the nv user memory is not cleared p.23
• The data in the receive buffer is not cleared p.23
• That was in effect when the power was turned on p.23
• Standard mode p.23
• This command has no effect in page mode p.25
• If this command is input in page mode the printer performs only internal flag p.25
• This command executes justification in the printing area p.25
• Beginning of the line p.25
• The width of normal characters p.25
• Aligns all the data in one line to the specified position p.25
• The horizontal tab position is stored as a value of character width x n p.25
• The command is enabled only when processed at the beginning of the line p.25
• Set is horizontal tab positions p.25
• Set horizontal tab positions p.25
• Select justification p.25
• Right side character spacing and double width characters are set with twice p.25
• Operation p.25
• N specifies the column number for setting a horizontal tab position from the p.25
• N selects the justification as follows p.25
• N 2 48 n 50 p.25
• Measured from the beginning of the line the character width includes the p.25
• K indicates the total number of horizontal tab positions to be set p.25
• This command justifies the space area according to p.25
• In standard mode p.25
• The esc command can also select the character fonts however the p.29
• Setting of the last received command is effective p.29
• Selects character fonts p.29
• Select character font p.29
• N 0 1 48 49 p.29
• Selects an international character set n from the following table p.30
• Select an international character set p.30
• Depending on the starting position of the printing area p.32
• Commands using vertical motion units esc sp esc esc p.32
• Commands using vertical motion units esc 3 esc j gs gs p.32
• Commands using horizontal motion units esc sp esc esc p.32
• Commands using horizontal motion units p.32
• ① if the starting position is the upper left or lower right of the printing p.32
• Area set by esc w p.32
• When the command is input in standard mode the printer executes only p.32
• Area data is buffered in the paper feed direction p.32
• This command sets the position where data is buffered within the printing p.32
• Area data is buffered in the direction perpendicular to the paper p.32
• Select the print direction and starting position in page mode p.32
• Select print direction in page mode p.32
• Parameters for horizontal or vertical motion units x or y differ as follows p.32
• N specifies the print direction and starting position as follows p.32
• N 3 48 n 51 p.32
• Internal flag operation this command does not affect printing in standard p.32
• If the starting position is the upper right or lower left of the printing p.32
• Feed direction p.32
• Selects a page n from the character code table p.33
• Select character code table p.33
• Clockwise rotated characters p.34
• Characters in the opposite directions from double height and double width p.34
• Always effective p.34
• When underline mode is turned on the printer does not underline 90 p.34
• Turns 90 clockwise rotation mode on or off p.34
• Turn 90 clockwise rotation mode on off p.34
• This command affects printing in standard mode however the setting is p.34
• N is used as follows p.34
• N 1 48 n 49 p.34
• Double width and double height commands in 90 rotation mode enlarge p.34
• Commands in normal mode p.34
• This command affects printing in standard mode however the setting is p.35
• N is used as follows p.35
• N 1 48 n 49 p.35
• Double width and double height commands in 90 rotation mode enlarge p.35
• Commands in normal mode p.35
• Clockwise rotated characters p.35
• Characters in the opposite directions from double height and double width p.35
• Always effective p.35
• When underline mode is turned on the printer does not underline 90 p.35
• Turns 90 clockwise rotation mode on or off p.35
• Turn 90 clockwise rotation mode on off p.35
• Print and eject label p.36
• Gs commands p.36
• Cmp 20 does not support p.36
• Table 2 character height table 2 character height p.37
• Table 1 character width p.37
• Selects the character height using bits 0 to 3 and selects the character width p.37
• Selection p.37
• Select character size p.37
• In standard mode the vertical direction is the paper feed direction and the p.37
• If n is outside of the defined range this command is ignored p.37
• Horizontal direction is perpendicular to the paper feed direction however p.37
• As follows p.37
• 1 vertical number of times 8 1 horizontal number of times 8 p.37
• Using bits 4 to 7 p.37
• This command is effective for all characters except for hri characters p.37
• ④ printer is reset or the power is turned off p.40
• ③ fs q is executed p.40
• Underline or character size white black reverse printing except for upside p.40
• This command is not affected by print modes emphasized double strike p.40
• This command is ignored if a downloaded bit image has not been defined p.40
• The print buffer p.40
• The following figure shows the relationship between the downloaded bit p.40
• Prints a downloaded bit image using the mode specified by m p.40
• Print down loaded bit image p.40
• M selects a mode from the table below p.40
• M 3 48 m 51 p.40
• In standard mode this command is effective only when the on data exists in p.40
• Image and the printed data p.40
• The contents of the macro can be defined up to 2048 bytes if the macro p.41
• Definition and clears the definition p.41
• Starts or ends macro definition p.41
• Start end macro definition p.41
• Operation macro definition ends when this command is received during p.41
• Macro is not defined when the power is turned on p.41
• Macro definition starts when this command is received during normal p.41
• Macro definition p.41
• If the printing area width set by gs l and gs w is less than one line p.41
• ② if the printing area width cannot be extended by one line in vertical p.41
• If the printer receives gs again immediately after previously receiving gs p.41
• ① the printing area width is extended to the right up to one line in p.41
• If the downloaded bit image to be printed exceeds the printable area the p.41
• Executes a macro p.41
• When gs is received during macro definition the printer ends macro p.41
• Execute macro p.41
• Vertical the following processing is performed only on the line in question p.41
• Excess data is not printed p.41
• Vertical in this case printing does not exceed the printable area p.41
• Esc can be included in the contents of the macro definition p.41
• The printer remains in the macro undefined state p.41
• Down mode p.41
• The left margin is reduced to accommodate one line in vertical p.41
• Definition exceeds 2048 bytes excess data is not stored p.41
• The defined contents of the macro are not cleared by esc therefore p.41
• Enables or disables asb and specifies the status items to include using n as p.44
• Enable disable automatic status back p.44
• Each status transmission represents the current status p.44
• Consecutive except for the xoff code p.44
• When using dle eot gs i or gs r the status transmitted by these p.44
• Commands and asb status must be differentiated p.44
• Changes the disabled status items may change in this case because p.44
• When the printer is turned on p.44
• Buffer there may be a time lag between data reception and status p.44
• Transmits the status when this command is executed the printer p.44
• Automatically transmits the status whenever the enabled status item p.44
• Transmission p.44
• The host is ready to receive data the four status bytes must be p.44
• The following four status bytes are transmitted without confirming whether p.44
• Since this command is executed after the data is processed in the receive p.44
• Printer data reception and transmission is possible at the first time from p.44
• If the asb is enabled as a default the printer transmits the status when the p.44
• If any of the status items in the table above are enabled the printer p.44
• If all status items are disabled the asb function is also disabled p.44
• Follows p.44
• First byte printer information p.45
• Bit 6 when printing is stopped due to high print head temperature until the p.45
• Bit 3 if these errors occur due to paper jams or the like it is possible to p.45
• 2 if an error due to a circuit failure e g wire break occurs it is p.45
• The status to be transmitted are as follows p.45
• Second byte printer information p.45
• Recover by correcting the cause of the error and executing dle enq n 1 n p.45
• Print head temperature drops sufficiently or when the paper roll cover is open p.45
• Impossible to recover p.45
• Turn white black reverse printing mode p.46
• This command is available for built in characters and user defined p.46
• This command does not affect the space between lines p.46
• This command does not affect bit image user defined bit image barcode p.46
• Third byte paper sensor information p.46
• Spacing set by esc sp p.46
• Only the lsb of n is effective p.46
• Hri characters and spacing skipped by h t esc and esc p.46
• Fourth byte paper sensor information p.46
• During printing bit 6 is on p.46
• Characters p.46
• White black reverse mode has a higher priority than underline mode even p.46
• When white black reverse printing mode is on it also applied to character p.46
• When the lsb of n is 1 white black reverse printing mode is turned on p.46
• When the lsb of n is 0 white black reverse printing mode is turned off p.46
• Turns on or off white black reverse printing mode p.46
• Selects the printing position of hri characters when printing a bar code p.48
• Selects a font for the hri characters used when printing a bar code p.48
• Select printing position of hri characters p.48
• N selects the printing position as follows p.48
• N selects the font from the following table p.48
• N 3 48 n 51 p.48
• N 0 1 48 49 p.48
• Hri means human readable interpretation p.48
• Hri characters are printed using the font specified by gs f p.48
• Hri characters are printed of the position specified by gs h p.48
• Font for human readable interpretation hri characters p.48
• ② m 73 n and d depends on the code system used p.49
• ① m 6 k and d depends on the code system used p.49
• Set bar code height p.49
• Selects a bar code system and prints the bar code p.49
• Select the height of the bar code p.49
• Print bar code p.49
• N specifies the number of dots in the vertical direction p.49
• M selects a bar code system as follows p.49
• If bar code width exceeds the printing area the printer does not print the bar code but moves p.50
• When the bar code system used is upc a or upc e the printer prints the bar code data after p.50
• Following data as normal data in this case the data buffer position does not change p.50
• When the bar code system used is jan 8 the printer prints the bar code after receiving 8 p.50
• Following data as normal data p.50
• When the bar code system used is jan 13 the printer prints the bar code after receiving 13 p.50
• Details in page mode details in page mode this command develops bar code data in the print buffer but does not print it after p.50
• Character data as bar code data p.50
• When code93 when code93 m 72 is used p.50
• Bytes bar code data and processes the following date as normal data p.50
• This command ends with a nul code p.50
• Bytes bar code data and processes the following data as normal data p.50
• The printer prints an hri character as start character at the beginning of the hri character p.50
• Bar code p.50
• The number of data for itf bar code must be even numbers when an odd number of data is p.50
• The data buffer position to the left side out of the printing area p.50
• Refer to figure 3 2 for bar code data buffer position p.50
• Receiving 12 bytes bar code data and processes the following data as normal data p.50
• Processing bar code data this command moves the print position to the right side dot of the p.50
• N indicates the number of bar code data and the printer processes n bytes from the next p.50
• Input the printer ignores the last received data p.50
• If n is outside of the specified range the printer stops command processing and processes the p.50
• If d is out of the specified range the printer stops command processing and processes the p.50
• Code a code b or code c which selects the first code set p.51
• ② special characters are defined by combining two characters and one character p.51
• ① the top of the bar code data string must be code set selection character any of p.51
• When using the code 128 in this printer take the following points into account for data p.51
• When code 128 m 73 is used p.51
• Transmission p.51
• The printer prints an hri character as a stop character at the end of the hri character p.51
• String p.51
• Refer to appendix j for the information of the code 128 bar code and is code table p.51
• Example printing gs k 72 7 67 111 100 101 13 57 51 p.51
• If combination of and the following character does not apply any special character the p.52
• Hri character for the function character is space p.52
• H are space p.52
• Gs k 73 10 123 66 78 111 46 123 67 12 34 56 p.52
• Example example data for printing no 123456 p.52
• Command processing and processes the following data as normal data p.52
• Be sure to keep spaces on both right and left sides of a bar code p.52
• Using code c p.52
• The printer does not print hri characters that correspond to the shift characters or code set p.52
• The asc character is defined by transmitting twice consecutively ⅱ p.52
• Spaces are different depending on the types of the bar code p.52
• Selection characters p.52
• Printer stops command processing and processes the following data as normal data p.52
• In this example the printer first prints no using code b then prints the following numbers p.52
• If the top of the bar code data is not the code set selection character the printer stops p.52
• If the printer receives characters that cannot be used in the special code set the printer stops p.52
• X 255 0 y 255 p.53
• Nl 0 nh 0 p.53
• When x and y are set to 0 the default setting of each value is used p.53
• Nh 255 p.53
• Vertical direction is the paper feed direction p.53
• Left margin printing width p.53
• This command is effective only of the beginning of a line p.53
• Inches and approximately 25 y mm 1 y inches respectively p.53
• This command does not affect printing in page made p.53
• If this command is input in page made the printer performs only internal flag p.53
• The left margin is set to nl nh 256 horizontal motion unit inches p.53
• If the setting exceeds the printable area the maximum value of the printable p.53
• The horizontal motion unit x is used for calculating the left margin p.53
• Area is used p.53
• The horizontal direction is perpendicular to the paper feed direction and the p.53
• The calculated result is truncated to the minimum value of the mechanical p.53
• Sets the left margin using nl and nh p.53
• Sets the horizontal and vertical motion units to approximately 25 x mm 1 x p.53
• Set left margin p.53
• Set horizontal and vertical motion units p.53
• Printable area p.53
• Operations p.53
• Nl 255 p.53
• Paper sensor status n 1 49 p.55
• N5 50 flow control p.55
• N4 49 n4 51 stop bits p.55
• N3 50 parity bits p.55
• N2 data length p.55
• N2 49 data length p.55
• N1 baud rate p.55
• N1 52 baud rate p.55
• N0 1 reserved p.55
• However if you use 7bit data you need to use parity bit if you set the parity p.55
• Gs s c p.55
• Goes off line and does not execute this command therefore bits 2 and 3 p.55
• Do not transmit the status of paper end p.55
• The status types to be transmitted are shown below p.55
• Change serial communication option p.55
• Set the serial option of the printer you can set baud rate data length p.55
• Bits 2 and 3 when the paper end sensor detects a paper end the printer p.55
• Parity bit stop bit flow control etc p.55
• Bit as none it will not work correctly p.55
• Gs s p p.56
• N time input time is minute input value is available from 1 60min p.57
• M 3 48 m 51 p.57
• K xl xh x 256 x yl yh x 256 k 0 p.57
• Yl yh select the number of data bytes xl xh 256 in the vertical direction p.57
• In standard mode this command is effective only when there is no data in p.57
• Yl 255 p.57
• In case the printer is under power save mode you need to send dummy p.57
• Xl xh selects the number of data bytes xl xh 256 in the horizontal p.57
• However when the usb cable is connected with the host the printer does p.57
• Xl 255 p.57
• Gs v 0 p.57
• Xh 255 p.57
• For the bit image p.57
• Usually send null 0 after send the dummy data host should wait for p.57
• Dummy data p.57
• This waiting time is required to protect the printer during the change from p.57
• Direction for the bit image p.57
• The value of m selects the mode as follows p.57
• Data to return the printer for normal mode for the dummy data sending p.57
• Selects raster bit image mode p.57
• Around 200ms for processing after that host can send the data for printing p.57
• Save mode you need to press the power button or need to send any p.57
• Print raster bit image p.57
• Power save mode to wake up the printer p.57
• Not go into power save mode or does not turn into power off mode p.57
• Multi level bar codes are as follows p.61
• Code39 itf codabar p.61
• Binary level bar codes are as follows p.61
• Upc a upc e jan13 ean13 jan8 ean8 code93 code128 p.61
• Set the horizontal size of the bar code p.61
• Set bar code width p.61
• N specifies the bar code width as follows p.61
• When you select the code page it will be saved in nv memory this is saved p.62
• The saved code page has been applied p.62
• Selects a page m from the character code table p.62
• N is the number of the image p.62
• Fs e p p.62
• Fs commands p.62
• Erase nv bit image p.62
• Delete the image stored in nv memory p.62
• Define code page p.62
• Although you power off the printer accordingly if you power on the printer p.62
• Underline thickness is not changed the default underline thickness is 1 dot p.67
• Changes p.67
• Underline printing is no longer performed but the previously specified p.67
• After the underline mode for characters is turned off by setting n to 0 p.67
• Underline mode on off p.67
• Turns underline mode for characters on or off based on the following values p.67
• Turns on underline mode for characters 2 dot thick p.67
• Turns on underline mode for characters 1 dot thick p.67
• Turns off underline mode for characters p.67
• The specified line thickness does not change even when the character size p.67
• The printer can underline all characters including right and left side p.67
• Sets the print mode for characters using n as follows p.67
• Set double width height p.67
• Received command is effective p.67
• N 2 48 n 50 p.67
• It is possible to turn underline mode on or off using fs and the last p.67
• Clockwise rotated characters p.67
• Character spacing but cannot underline the space set by ht and 90 p.67
• When both double width and double height modes are set including right p.68
• The thickness of the underline is that specified by fs regardless of the p.68
• The printer can underline all characters including right and left side p.68
• The last received command is effective p.68
• Select ms track p.68
• Select card reader mode p.68
• Of the last received command is effective p.68
• N read track data p.68
• N 52 n 36 p.68
• It is possible to turn under line mode on or off using fs and the setting p.68
• It is possible to emphasize the character using fs w or gs the setting of p.68
• Clockwise rotated characters p.68
• Characters on the line are aligned at the baseline p.68
• Character spacing but cannot underline the space set by ht and 90 p.68
• Character size p.68
• And left side character spacing quadruple size characters are printed p.68
• When some of the characters in a line are double or more height all the p.68
• Track iii data length 106 byte p.69
• Track ii data length 37 byte p.69
• Track i data length 76byte p.69
• Magnetic card read out put format p.69