![Citizen PHU-500 [65/186] Gs r n](/img/pdf.png)
Citizen PHU-500 [65/186] Gs r n
![Citizen PHU-500 [65/186] Gs r n](/views2/1844074/page65/bg41.png)
- 64 -
GS r n
[Function] Sending status
[Code] <1D>H<72>H<n>
[Range]
n=1, 49
[Outline]
• Sends the specified status to the host.
n
Function
1, 49
Sends the Paper Sensor status.
2, 50
Sends the Drawer Kick-out Connector status.
[Caution]
• When the serial interface is used:
For DTR/DSR control:
The printer sends the status after verifying that the host is ready to receive. If the host is not ready to
receive, the printer waits for the host to become ready to receive.
For XON/XOFF control:
The printer sends the status without checking whether the host is ready to receive or busy.
• Because this command is executed when data is mapped in the receive buffer, there may be a delay
between receiving the command and sending the status depending on the condition of the receive buffer.
• If ASB (Automatic Status Back) is enabled by GS a, the host must discriminate between the status due to this
command and the status due to ASB.
• Whenever the Paper-end Sensor detects a “paper out” state, the printer goes offline, and the command is not
executed. Therefore, the printer never sends a status “No paper in Paper-end detector (0CH)”.
• At the setting of MSW3-7 OFF, paper sensor status is fixed to 00h.
Содержание
- Command reference p.1
- Revision 1 3 p.1
- Model pmu3300 p.1
- Table of contents 2 p.3
- Table of contents p.3
- Print position commands 35 p.3
- Print character commands 16 p.3
- Outline 6 p.3
- Esc pos p.3
- Detail 7 p.3
- Description of items 10 2 print control commands 11 p.3
- Control command details 6 1 how to send control commands 6 p.3
- Kanji control commands 87 p.4
- Cutter commands 71 p.4
- Commands for non volatile memory 84 p.4
- Bit image commands 50 p.4
- Bar code commands 74 p.4
- Status commands 56 p.4
- Paper detecting commands 66 p.4
- Panel switch commands 68 p.4
- Macro commands 69 p.4
- Line feed span commands 48 p.4
- Printer function setting commands 97 p.5
- Other commands 132 p.5
- Dimensional code commands 123 p.5
- Page mode 177 p.6
- Memory switch 160 p.6
- Character code table 144 p.6
- Appendix 177 p.6
- Control commands p.7
- Control command details p.7
- Citizen p.7
- Character set p.7
- Outline p.7
- Operation mode p.7
- How to send control commands p.7
- Print position commands p.8
- Print control commands p.8
- Print character commands p.8
- Esc pos command list p.8
- Detail p.8
- Command function mode gs p page p.8
- Macro commands p.9
- Line feed span commands p.9
- Cutter commands p.9
- Commands for non volatile memory p.9
- Command function mode gs p page p.9
- Bit image commands p.9
- Bar code commands p.9
- Status commands p.9
- Paper detecting commands p.9
- Panel switch commands p.9
- Printer function setting commands p.10
- Other commands p.10
- Kanji control commands p.10
- Dimensional code commands p.10
- Command function mode gs p page p.10
- Description of items p.11
- Command details p.11
- Print control commands p.12
- Aaa bbb p.13
- Ff at selection of page mode p.14
- Esc ff p.14
- Esc j n p.15
- Esc d n p.16
- Print character commands p.17
- Ａ ａ ａ ａ ａ ａ ａ ａ ａ ａ p.18
- Esc sp n p.18
- Esc s n m a p s x a m n 1 p.22
- Ａａａａａａａａａａ p.23
- Ａａａｂｂｂ p.25
- Esc e n p.25
- Ａａａｂｂｂ p.26
- Esc g n p.26
- Esc m n p.27
- Esc r n p.28
- Esc v n p.29
- Esc t n p.30
- Gs b n p.34
- Gs b n p.35
- Aaa bbb aaa bbb p.36
- Print position commands p.36
- Aaa bbb ccc p.36
- Esc n1 n2 p.37
- 100 256 a b c a b a p.37
- Esc d n k null p.38
- Esc t n p.39
- Esc w xl xh yl yh dxl dxh dyl dyh p.40
- Pmu3300 p.41
- Dxl and dxh is the case of basic calculation pitch x 203 p.41
- Esc nl nh p.42
- Esc a n p.43
- Gs nl nh p.44
- Gs l nl nh p.45
- Gs w nl nh p.46
- Pmu3300 p.47
- Gs nl nh p.48
- Line feed span commands p.49
- Esc 3 n p.50
- Esc m n1 n2 d k p.51
- Bit image commands p.51
- The specification which depend on the model 1 4 unit dpi p.52
- Support model p.52
- Pmu3300 p.52
- Normal printing data p.52
- Caution when the value of m is out of the above range the data following after n1 is processed as p.52
- After completion of bit image printing the printer returns to normal data processing mode p.52
- Gs n1 n2 d n1xn2x8 p.53
- Gs v 0 m xl xh yl yh d1 dk p.55
- ドット 512ドット p.56
- Status commands p.57
- Dle eot n p.57
- A paper jam error occurred p.58
- The cause of the error and then dle enq n 1 n 2 can be used to recover from the error however it is not possible to recover from any error due to a circuit problem e g broken wire p.58
- State or if the printer is out of paper when the paper near end sensor is enabled by esc c 4 at this time bit 5 1 p.58
- Pmu3300 p.58
- No paper jam error occurred p.58
- Head temperature falls at this time bit 6 1 p.58
- Bit 6 if a head overheat error is detected the printing is stopped until the p.58
- Bit 5 printing is stopped if the paper end detector detects a paper out p.58
- Bit 2 in case of msw3 8 on it is generated by cover open bit 3 if this error occurred because of a paper jam for example remove p.58
- Gs a n p.61
- Gs r n p.65
- Paper detecting commands p.67
- Esc c 3 n p.67
- Esc c 4 n p.68
- Panel switch commands p.69
- Esc c 5 n p.69
- Macro commands p.70
- Gs n1 n2 n3 p.71
- Cutter commands p.72
- Gs v m n 2 p.74
- Gs v m 1 gs v m n 2 p.74
- Gs v m 1 p.74
- Gs h n p.75
- Bar code commands p.75
- Gs f n p.76
- Gs h n p.77
- Gs1 databar truncated n 13 4 p.78
- Gs1 databar mnidirectional n 13 4 p.78
- Gs1 databar limited n 13 4 p.78
- Gs1 databar expanded p.78
- 2 gs k m n d1 dn p.78
- 1 gs k m d1 dk nul 2 gs k m n d1 dn p.78
- 1 gs k m d1 dk nul p.78
- This bar code consisting of numerals only has a fixed length of 13 columns the minimum height of the bar is 33 times of module size p.82
- Gs w n p.84
- Fs p n m p.85
- Commands for non volatile memory p.85
- Xl xh yl yh d1 dk 1 xl xh yl yh d1 dk n p.86
- Fs q n xl xh yl yh d1 dk 1 xl xh yl yh d1 dk n p.86
- Kanji control commands p.88
- 漢字 p.89
- 漢字漢字 p.90
- Fs 2 a1 a2 d k p.92
- Jis code system are 21 7eh jis 1 side and a1h feh jis 2 side for both p.94
- Fs c n p.94
- Byte the address is invalid p.94
- Byte if msb is not same between p.94
- Byte and p.94
- Fs s n1 n2 p.95
- 漢字 p.96
- Fs w n p.96
- Fs a pl ph fn m p.97
- Fs a pl ph fn p.97
- Fn 48 function 48 set kanji fonts p.97
- Printer function setting commands p.98
- Gs e pl ph fn p.98
- Function 104 p.98
- Function 103 p.98
- Gs e pl ph fn d1 d2 d3 p.99
- Gs e pl ph fn d1 d2 p.99
- Fn 2 function 2 end of printer function setting mode p.99
- Fn 1 function 1 transferring to printer function setting mode p.99
- Gs e pl ph fn a1 b18 b11 ak bk8 bk1 p.100
- Fn 3 function 3 setting memory switch value p.100
- A 1 2 3 4 5 6 p.100
- Setting msw 4 a 4 p.101
- Setting msw 3 a 3 p.101
- Setting msw 2 a 2 p.101
- Setting msw 1 a 1 p.101
- Pmu3300 p.101
- Platen ope p.101
- Msw 4 1 2 are valid when msw 3 4 is on setting msw 5 a 5 p.102
- Gs e pl ph fn a p.103
- Fn 4 function 4 sending the set memory switch value p.103
- A 1 2 3 4 5 p.103
- Gs e pl ph fn a1 n1l n1h ak nkl nkh p.104
- Fn 5 function 5 setting customized value p.104
- A 5 6 213 214 216 217 218 249 p.104
- A 216 select the jis shift jis specified by nl nh 256 p.106
- A 214 select the enable disable of kanji specified by nl nh 256 p.106
- A 213 selects the flow control specified by nl nh 256 when virtual p.106
- Pmu3300 p.106
- Com is set p.106
- A 6 sets printing speed to the value specified by nl nh 256 p.106
- A 5 sets printing density to the level specified by nl nh 256 p.106
- A 217 select the international character set specified by nl nh 256 p.106
- Gs e pl ph fn a p.108
- Fn 6 function 6 sending the set customized value p.108
- A 5 6 213 214 216 217 218 249 p.108
- Pmu3300 p.110
- Jis 49 1 p.110
- Byte 2nd byte 3rd byte 4th byte 5th byte p.110
- A 6 when printing speed is specified p.110
- A 5 when print density is specified p.110
- A 216 when jis shift jis is specified p.110
- A 214 when kanji is specified p.110
- A 213 when the flow control of virtual com is specified p.110
- Stored value jis shift jis p.110
- Shift jis 50 2 p.110
- Setting status sending data p.110
- Stored value emulation 1st byte 2nd byte 3rd byte 4th byte 5th byte p.111
- Setting status sending data p.111
- Esc pos 49 1 p.111
- Axiohm2 51 3 p.111
- Axiohm1 50 2 p.111
- A 249 emulation is specified p.111
- A 218 when codepage is specified p.111
- A 217 when international character set is specified p.111
- Gs e pl ph fn a d1 d2 p.112
- Fn 7 function 7 copying user defined page p.112
- Fn 8 function 8 defining data by the column format to character code page of work area p.113
- Data structure 9 17 d1 d4 d25 d3 d6 d27 p.113
- Bits 6 through 0 are not character data p.113
- Range 5 pl ph 256 65535 fn 8 y 2 at selection of font c y 3 at selection of other than font c 128 c1 c2 255 0 x 12 at selection of font a 0 x 9 at selection of font b 0 x 8 at selection of font c 0 d 255 k c2 c1 1 p.113
- Outline defines the data in column format in units of character on the code page in ram operates only in printer function setting mode p.113
- Gs e pl ph fn y c1 c2 xd1 d y x k p.113
- ビット3 0は文字データの対象にはならない p.114
- Range 5 pl ph 256 65535 fn 9 x 1 at selection of font c x 2 at selection of other than font c 128 c1 c2 255 0 y 24 at selection of font a 0 y 16 at selection of font c 0 d 255 k c2 c1 1 0 x 17 at selection of font b p.114
- Outline defines the data in raster format in units of character on the character code page in work area operates only in printer function setting mode p.114
- Gs e pl ph fn x c1 c2 y d1 d x y k p.114
- Fn 9 function 9 defining data in the raster format to the character code page of work area p.114
- Data structure data structur p.114
- D1 odd number d2 even number p.114
- Bits 3 through 0 are not character data p.114
- Gs e pl ph fn c1 c2 p.115
- Fn 10 function 10 erasing data of character code page data in work area p.115
- Gs e pl ph fn a d1 dk p.116
- Fn 11 function 11 setting communication conditions p.116
- Default p.116
- Gs e pl ph fn a p.117
- Fn 12 function 12 sending the set communication conditions p.117
- Gs e pl ph fn nl nh p.118
- Fn 103 function 103 set the printable area width fn 103 function 103 set the printable area width p.118
- Gs e pl ph fn p.119
- Fn 104 function 104 send the printable area width p.119
- Gs e pl ph fn a p.120
- Fn 255 function 255 setting all contents set by printer function setting mode to the state at shipment p.120
- Gs k pl ph fn m p.121
- Gs k pl ph fn m p.122
- Fn 49 function 49 setting printing density p.122
- Gs k pl ph fn m p.123
- Fn 50 function 50 setting printing speed p.123
- Gs k pl ph cn fn parameter p.124
- Dimensional code commands p.124
- Fn 65 function 65 setting the number of digits of pdf417 p.125
- Gs k pl ph cn fn n p.125
- Fn 66 function 66 setting the number of steps of pdf417 p.125
- Gs k pl ph cn fn n p.126
- Fn 68 function 68 setting the height of step of pdf417 p.126
- Fn 67 function 67 setting module width of pdf417 p.126
- Gs k pl ph cn fn m n p.127
- Fn 69 function 69 setting error correction level of pdf417 p.127
- Gs k pl ph cn fn m d1 dk p.128
- Gs k pl ph cn fn m p.128
- Fn 80 function 80 storing received data to 2d code data storage area p.128
- Fn 70 function 70 setting options for pdf417 p.128
- Gs k pl ph cn fn m p.129
- Fn 81 function 81 printing 2d code data in 2d code data storage area p.129
- Gs k pl ph cn fn n p.130
- Fn 67 function 167 sets the module width of qrcode p.130
- Fn 65 function 165 specifying qrcode model p.130
- Gs k pl ph cn fn n1 n2 p.130
- Gs k pl ph cn fn n p.131
- Gs k pl ph cn fn m d1 dk p.131
- Fn 80 function 180 storing received data to 2d code data storage area p.131
- Fn 69 function 169 setting qrcode error correction level p.131
- Gs k pl ph cn fn m p.132
- Fn 81 function 181 printing 2d code data in 2d code data storage area p.132
- Other commands p.133
- Dle enq n p.133
- Dle dc4 fn m t specification of fn 1 p.134
- Dle dc4 fn d1 d7 specification of fn 8 p.135
- Ff can esc ff esc s esc t esc w gs w gs p.138
- Gs a pl ph n m p.140
- Gs i n p.141
- Pmu3300 p.142
- Gs p x y p.143
- Codepage 00h to 7fh pc864 arabic p.154
- Codepage 00h to 7fh thai code 11 p.156
- Codepage 00h to 7fh thai code 18 p.157
- Memory switches p.161
- Memory switch p.161
- Msw1 2 input buffer p.164
- Msw1 1 setting the power on notify p.164
- Details of memory switches p.164
- Msw1 4 receive error character p.165
- Msw1 3 busy condition p.165
- Msw1 8 init signal p.166
- Msw1 7 dsr signal p.166
- Msw1 5 cr code p.166
- Msw2 3 buffering p.167
- Msw2 2 auto cutter operation p.167
- Msw2 4 full columns print p.168
- Msw2 8 pne sensor p.168
- Msw2 5 cover close return p.168
- Msw3 6 time out cut pmu3300 only p.169
- Msw3 2 clearing cover open error p.169
- Msw3 1 auto cutter return p.169
- Ct s300 unique p.169
- Msw3 8 cover open during printing p.170
- Msw3 7 cbm compatible mode p.170
- Msw4 8 forcible partial cut p.171
- Msw4 3 paper feed cut at closing cover p.171
- Msw7 5 flow control p.174
- Msw7 4 parity p.174
- Msw7 3 stop bit p.174
- Msw7 2 data length p.174
- Msw7 1 baud rate p.174
- Ct s801 ct s851 ct s601 ct s651 ct s251 unique p.176
- Msw9 4 jis ct s280 ct s281 ct s310 ct s310ii ct s2000 ct s4000 p.176
- Msw9 3 kanji p.176
- Msw9 2 international character p.176
- Msw9 1 code page p.176
- Values set by each command in standard mode and page mode p.178
- Overview p.178
- Explanation on page mode p.178
- Appendix p.178
- Mapping of print data in the print area p.179
- Double height character p.180
- Page mode lesson p.181
- Example of using page mode p.181
- 0 0 200 p.181
- Can command p.183
- Abcdefghijklmnop p.183
- 0 0 200 p.183
- Qrst1234567890 p.183
- Page mode lesson p.183
- Identification of send status p.185
Похожие устройства
-
Citizen PHU-500Инструкция по монтажу -
Citizen PHU-500Руководство по эксплуатации -
Citizen PHU-500Техническое описание -
Citizen PMU2300IIРуководство по эксплуатации -
Citizen PMU2300IICommand Reference -
Citizen CBM-920IIРуководство по эксплуатации -
Citizen CBM-920IIБрошюра -
Citizen CBM-920IIТехническое описание -
Citizen CL-S521Руководство по эксплуатации -
Citizen CL-S521Autocutter -
Citizen CL-S521Quick Settings and Error Manual -
Citizen CL-S521Compatible Network Cards