Home
Главная
Hander
Шлифовальная Машина
HBS-730
Инструкция по эксплуатации Страница: 2

Hander HBS-730 [2/34] English

Hammer drill

INTENDED USE

This tool is intended for hammer drilling in brick,

concrete and stone as well as for drilling in wood,

metal, ceramic and plastic. Tools with electronic

speed control and left/right rotation are also suitable

for screwdriving and thread cutting

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1 On/Off switch with speed control

2 Switch locking button

3 Wheel for maximum speed control

4 Switch for changing direction of rotation

5 Switch for selecting drilling function

6 Auxiliary handle

SAFETY

WARNING! Read all instructions. Failure to follow

all instructions listed below may result in electric

shock, fire and/or serious injury.

● Wear ear protectors with hammer drills (exposure

to noise can cause hearing loss)

● Use auxiliary handles supplied with the tool (loss

of control can cause personal injury)

● Avoid damage that can be caused by screws,

nails and other elements in your workpiece; remove

them before you start working

● Always keep the cord away from moving parts of

the tool

● When you put away the tool, switch off the motor

and ensure that all moving parts have come to a

complete standstill

● Use completely unrolled and safe extension cords

with a capacity of 16 Amps (UK 13 Amps)

● In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the

plug

● SBM Group can assure flawless functioning of

the tool only when original accessories are used

● Use only accessories with an allowable speed

matching at least the highest no-load speed of the

tool

● This tool should not be used by people under the

age of 16 years

● Be careful not to drill or drive into areas where

electrical wires may be contacted

● If the cord is damaged or cut through while

working, do not touch the cord, but immediately

disconnect the plug

● Never use tool when cord is damaged; have it

replaced by a qualified person

● Always check that the supply voltage is the same

as the voltage indicated on the nameplate of the

tool (tools with a rating of 230V or 240V can also be

connected to a 220V supply)

● If the drill bit becomes unexpectedly jammed

(causing a sudden, dangerous reaction),

immediately switch off the tool

● Be aware of the forces that occur as a result of

jamming (especially when drilling metals); always

hold the tool firmly with both hands and take a

secure stance

● Always disconnect plug from power source before

making any adjustment or changing any accessory

● Holding the tool

- keep the ventilation slots uncovered

- do not apply too much pressure on the tool; let the

tool do the work for you

Your machine is double insulated in

accordance with EN 50144; therefore

no earthwire is required.

MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work

on the motor.

Regularly clean the machine housing with a soft

cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt.If the dirt

does not come off use a soft cloth moistened with

soapy water. Never use solvents such as petrol,

alcohol, ammonia water, etc. These solvents may

damage the plastic parts.

The machine requires no additional lubrication.

Should a fault occur, e.g. after wear of a part,

please contact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage

during transport, it is delivered in a sturdy

packaging. Most of the packaging materials can be

recycled. Take these materials to the appropriate

recycling locations. Take your unwanted machines

to your local SBM Group dealer. Here they will be

disposed of in an environmentally safe way.

English

1 3

max 60-80%

100%

Belt sander

INTENDED USE

This tool is intended for dry sanding with high removal

performance of wood, plastic, metal, etc.

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1 On/off switch

2 Knob for locking on/off switch

3 Lever for changing sanding belt

4 Arrow

5 Knob for adjusting belt centering

6 Dustbag

SAFETY

WARNING! Read all instructions. Failure to follow all in-

structions listed below may result in electric shock, ﬁ re

and/or serious injury.

● Avoid damage that can be caused by screws, nails

and other elements in your workpiece; remove them

before you start working

● Always keep the cord away from moving parts of the

tool; direct the cord to the rear away from the tool

● When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

● Use completely unrolled and safe extension cords

with a capacity of 16Amps (U.K. 13 Amps)

● In case of electrical or mechanical malfunction, imme-

diately switch off the tool and disconnect the plug

● SBM GROUP can assure ﬂ awless functioning of the

tool only when original accessories are used

● This tool should not be used by people under the age

of 16 years

● The noise level when working can exceed 85 dB(A);

wear ear protection

● If the cord is damaged or cut through while working,

do not touch the cord, but immediately disconnect the

plug

● Never use tool when cord is damaged; have it re-

placed by a qualiﬁ ed person

● Always check that the supply voltage is the same as

the voltage indicated on the nameplate of the tool (tools

with a rating of 230V or 240V can also be connected to

a 220V supply)

● This tool is not suitable for wet sanding

● Do not work materials containing asbestos (as-

bestos is considered carcinogenic)

● Take protective measures when during work dust

can develop that is harmful to one’s health, com-

bustible or explosive (some dusts are considered car-

cinogenic); wear a dust mask and work with dust/chip

extraction when connectable

● When sanding metal, sparks are generated; do not

use dustbox/dustbag/vacuum cleaner and keep other

persons and combustible material from work area

● Do not touch the running sanding belt

● Do not continue to use worn, torn or heavily clogged

sanding belts

● Wear protective gloves, safety glasses, close-ﬁ tting

clothes and hair protection (for long hair)

● Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K.

ONLY):

● Do not connect the blue (= neutral) or brown (= live)

wire in the cord of this tool to the earth terminal of the

plug

● If for any reason the old plug is cut off the cord of

this tool, it must be disposed of safely and not left unat-

tended

● before the sanding surface reaches the workpiece,

you should switch on the tool

● before switching off the tool, you should lift it from

the workpiece

Your machine is double insulated in accord-

ance with EN 50144; therefore no earthwire is

required.

MAINTENANCE

Make sure that the machine is not live when

carrying out maintenance work on the motor.

Regularly clean the machine housing with a soft cloth,

preferably after each use. Keep the ventilation slots free

from dust and dirt.If the dirt does not come off use a soft

cloth moistened with soapy water. Never use solvents

such as petrol, alcohol, ammonia water, etc. These sol-

vents may damage the plastic parts.

The machine requires no additional lubrication.

Should a fault occur, e.g. after wear of a part, please

contact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during

transport, it is delivered in a sturdy packaging. Most of

the packaging materials can be recycled. Take these

materials to the appropriate recycling locations. Take

your unwanted machines to your local SBM Group

dealer. Here they will be disposed of in an environmen-

tally safe way.

English

Hander HBS-730 [2/34] English

Содержание

Похожие устройства